1. Manuals
  2. Brands
  3. Gigabyte Manuals
  4. Motherboard
  5. GA-8IE533
  6. User manual

Gigabyte GA-8IE533 User Manual

P4 titan 533 motherboard
Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
When you installing AGP card, please make sure the follow
ing notice is fully understood and practiced. If your AGP
card has "AGP 4X notch"(show below), please make sure
your AGP card is AGP 4X (1.5V).
Caution: AGP 2X(3.3V) card is not supported by Intel
845
®
(E/G)/ Intel
850(E) . You might experience system unable to
®
boot up normally. Please insert an AGP 4X/8X(1.5V) card
Example 1: Diamond Vipper V770 golden finger is compatible
with 2X/4X mode AGP slot. It can be switched between AGP 2X
(3.3V) or 4X(1.5V) mode by adjusting the jumper. The factory
default for this card is 2X(3.3V).
GA-8IE533
The
(or any AGP 4X
only) motherboards might not function properly, if you install this card
without switching the jumper to 4X(1.5) mode in it.
Example 2: Some ATi Rage 128 Pro graphics cards made by
"Power Color", the graphics card manufacturer & some SiS 305
cards, their golden finger is compatible with 2X/4X mode AGP
slot, but they support 2X(3.3V) only.
GA-8IE533
The
(or any AGP
4X only) motherboards might not function properly, If you install this
card in it.
Note : Although Gigabyte's AG32S(G) graphics card is based on
ATi Rage 128 Pro chip, the design of AG32S(G) is compliance
with AGP 4X (1.5V) specification. Therefore, AG32S (G)will work
fine with Intel
845(E/G) / 850(E) based motherboards.
®

Advertisement

Table of Contents
loading

Related Manuals for Gigabyte GA-8IE533

Summary of Contents for Gigabyte GA-8IE533

  • Page 1 4X only) motherboards might not function properly, If you install this card in it. Note : Although Gigabyte's AG32S(G) graphics card is based on ATi Rage 128 Pro chip, the design of AG32S(G) is compliance with AGP 4X (1.5V) specification. Therefore, AG32S (G)will work fine with Intel 845(E/G) / 850(E) based motherboards.
  • Page 2 M The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. M Third-party brands and names are the property of theirrespective owners.

  • Page 3: Declaration Of Conformity

    EN 60335 Safety of household and similar electrical appliances (Stamp) (full address) GA-8IE533 o EN 61000-3-2* Disturbances in supply systems cause T EN 60555-2 by household appliances and similar electrical equipment “Harmonics” o EN 61000-3-3*...
  • Page 4 (2) this device must accept any inference received, including that may cause undesired operation. Representative Person’s Name: Signature: Eric Lu Date: G.B.T. INC. (U.S.A.) 17358 Railroad Street City of Industry, CA 91748 (818) 854-9338/ (818) 854-9339 Motherboard GA-8IE533 ERIC LU August 23 ,2002...
  • Page 5 GA-8IE533 P4 Titan 533 Motherboard USER'S MANUAL Pentium 4 Processor Motherboard ® Rev. 1001 12ME-8IE533-1001...

  • Page 6: Table Of Contents

    Item Checklist ...3 WARNING! ...3 Chapter 1 Introduction ...4 Features Summary ... 4 GA-8IE533 Motherboard Layout ... 6 Chapter 2 Hardware Installation Process ...7 Step 1: Install the Central Processing Unit (CPU) ... 8 Step 1-1 CPU Installation ... 8 Step 1-2 : CPU Heat Sink Installation ...
  • Page 7 Power Management Setup ... 33 PnP/PCI Configurations... 36 PC Health Status ... 37 Frequency/Voltage Control ... 39 Top Performance... 41 Load Fail-Safe Defaults ... 42 Load Optimized Defaults ... 43 Set Supervisor/User Password ... 44 Save & Exit Setup ... 45 Exit Without Saving ...

  • Page 8: Item Checklist

    þ Quick PC Installation Guide o RAID Manual WARNING! Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electricity, you should follow some precautions whenever you work on your computer.

  • Page 9: Chapter 1 Introduction

    Chapter 1 Introduction Features Summary Form Factor — 29.3cm x 20.0cm ATX size form factor, 4 layers PCB. — Socket 478 for Intel — Intel Pentium — Support Intel — 2nd cache depend on CPU Chipset — Chipset 845E HOST/AGP/Controller —...
  • Page 10 CPU, chipset and most of the peripherals. Whether your system can run under these specific bus frequencies properly will depend on your hardware configurations, including CPU, Chipsets,SDRAM,Cards… .etc. GA-8IE533 Motherboard - 6 -...

  • Page 11: Ga-8Ie533 Motherboard Layout

    GA-8IE533 Motherboard Layout KB_MS ATX_12V CPU_FAN AC 97 SUR_CEN P4 Titan533 I T8712 BIOS SPDIF SPDI F _ IN SOC KET478 Intel 845E PCI1 PCI2 ICH4 PCI3 PCI4 PCI5 PWR_LE D F_PA NEL F_U SB1 F_U SB2 Front USB 2.0...

  • Page 12: Chapter 2 Hardware Installation Process

    Step 3- Install expansion cards Step 4- Connect ribbon cables, cabinet wires, and power supply Step 5- Setup BIOS software Step 6- Install supporting software tools Step4 Step 4 Step3 GA-8IE533 Motherboard Step 2 Step1 Step 4 Step 4 - 8 -...

  • Page 13: Step 1: Install The Central Processing Unit (Cpu)

    Step 1: Install the Central Processing Unit (CPU) Step 1-1: CPU Installation Angling the rod to 65 1. Angling the rod to 65-degree maybe feel a kind of tight , and then continue pull the rod to 90-degree when a noise “ cough” made.

  • Page 14: Step 1-2 : Cpu Heat Sink Installation

    M Make sure the CPU fan power cable is plugged in to the CPU fan connector, this completes the installation. M Please refer to CPU heat sink user’ s manual for more detail installation procedure. GA-8IE533 Motherboard 2. Make sure the CPU fan is plugged to the CPU fan connector, than install complete.

  • Page 15: Step 2: Install Memory Modules

    Step 2: Install memory modules The motherboard has 3 dual inline memory module (DIMM) sockets, but it can only support a maximum of 4 banks of DDR memory. DDR sockets 1 uses 2 banks, DDR sockets 2&3 share the remaining 2 banks. Please refer to the following tables for possible memory configurations supported. The BIOS will automatically detects memory type and size.

  • Page 16: Step 3: Install Expansion Cards

    7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS. 8. Install related driver from the operating system. AGP Card GA-8IE533 Motherboard Please carefully pull out the small white- drawable bar at the end of the AGP slot when you try to install/ Uninstall the AGP card.

  • Page 17: Step 4: Connect Ribbon Cables, Cabinet Wires, And Power Supply

    Step 4: Connect ribbon cables, cabinet wires, and power supply Step 4-1 : I/O Back Panel Introduction u PS/2 Keyboard and PS/2 Mouse Connector PS/2 Mouse Connector (6 pin Female) PS/2 Keyboard Connector (6 pin Female) v USB Connector USB 0 USB 1 ØThis connector supports standard PS/2 keyboard and PS/2 mouse.

  • Page 18: Audio Connectors

    (Rear Speaker) If you want the detail information for 2-/4-/6-channel audio setup installation, please refer to "2-/4-/6-Channel Audio Function Introduction ". GA-8IE533 Motherboard ØThis connector supports 2 standard COM ports and 1 Parallel port. Device like printer can be connected to Parallel port ; mouse and modem etc can be connected to Serial ports.

  • Page 19: Step 4-2 :Connectors & Jumper Setting Introduction

    Step 4-2 :Connectors & Jumper Setting Introduction 1) CPU_FAN 2) SYS_FAN 3) ATX_12V 4) ATX Power 5) FDD 6) IDE1/IDE2 7) RAM_LED 8) PWR_LED 9) F_PANEL 10) F_USB1/F_USB2 11) SPDIF 12) SPDIF_IN 13) SUR_CEN 14) CD_IN 15) AUX_IN 16) F_AUDIO 17) CI 18) BAT - 15 -...
  • Page 20 +12V 5V SB (Stand by +5V) Power Good 3.3V 3.3V GA-8IE533 Motherboard Ø Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running under abnormal condition or damaged by overheating.The CPU fan connector supports Max. current up to 600mA .
  • Page 21 5)Floppy Connector] 6)IDE1 / IDE2 Connector (Primary/Secondary] IDE2 IDE1 7)RAM_LED 8)PWR_LED Ø Important Notice: The red stripe of the ribbon cable must be the same side with the Pin1. Ø Important Notice: Please connect first harddisk to IDE1 and connect CD_ROM to IDE2. The red stripe of the ribbon cable must be the same side with the Pin1.
  • Page 22 10)F_ USB1 / F_USB2 (Front USB Connector, Yellow Connector) F_USB1 F_USB2 GA-8IE533 Motherboard Ø Be careful with the polarity of the front USB connector. Check the pin assignment while you connect the front USB cable. Please contact your nearest dealer for optional front USB cable.
  • Page 23 11)SPDIF 12)SPDIF_IN 13)SUR_CEN SUR OUTR BASS_OUT CENTER_OUT SUR OUTL 14)CD_IN (CD Audio Line In Connector) CD-L CD-R Ø The SPDIF output is capable of providing digital audio to external speakers or com pressed AC3 data to an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input function.
  • Page 24 Front Audio (L) Rear Audio (L) 17 ) CI Signal 18) BAT (Battery) GA-8IE533 Motherboard Ø Connect CD-ROM or DVD-ROM audio out to the connector. Ø If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper.

  • Page 25: Chapter 3 Bios Setup

    Chapter 3 BIOS Setup BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the pow er is turned off. ENTERING S ETUP Aft e r pow er on the computer, pressing <Del>...

  • Page 26: The Main Menu (For Example: Bios Ver. :F1)

    This setup page includes all the items in standard compatible BI OS. Advanced B IOS Features This setup page includes all the items of Award special enhanced features. GA-8IE533 Motherboard Top Performance Load Fail-Safe Defaults Load Optimi z ed Defaults...

  • Page 27: Pc Health Status

    Integrated Peri pherals This setup page includes all onboard peripherals. Power Management S etup This setup page includes all the items of Green function features. PnP/PCI Confi gurations This setup page includes all the configurations of PCI & PnP I SA resources. PC Health Status This setup page is the System auto detect Temperature, voltage, fan, speed.

  • Page 28: Standard Cmos Features

    The times format in <hour> <minute> <second>. The time i s calcul a ted base on the 24-hour milit a ry - time cl o ck. For ex ample, 1 p.m. i s 13:00:00. GA-8IE533 Motherboard Thu, Feb 21 2002...
  • Page 29 F IDE Primary Mas ter, S lave / Secondary Master, Slave The category identi f ies the ty pes of hard disk from dri v e C to F that has been installed in the computer. There are t w o ty pes: auto type, and manual ty pe. Manual t y pe is user-definable; Auto ty pe w hich w ill automatically detect HDD type.

  • Page 30: Base Memory

    Extended Memory The BIOS determines how much extended memory is present during the P OST. This is the amount of memory located above 1 MB in the CPU’ s memory address map. GA-8IE533 Motherboard - 26 -...

  • Page 31: Advanced Bios Features

    Advanced BIOS Features CMOS Setup Utili t y -Copy right (C) 1984-2002 Aw ard Soft w are Adv anced BI O S Feat u res First Boot Dev ice Second Boot Dev ice Third Boot Dev ice Boot Up Floppy Seek DRAM Data Integrit y Mode Init Display First hhigf: Mov e Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F1:General Help...

  • Page 32: Boot Up Floppy Seek

    AGP VGA card and a PCI VGA card on board. Set I n it Display First to PCI Slot. 8PCI Set I n it Displ a y First to AGP. (Default value) 8AGP GA-8IE533 Motherboard - 28 -...

  • Page 33: Integrated Peripherals

    Integrated Peripherals CMOS Setup Utili t y -Copy right (C) 1984-2002 Aw ard Soft w are Integrated Peripherals On-Chip Pri m ary PCI IDE On-Chip Secondary PCI IDE IDE1 Conductor Cable IDE2 Conductor Cable USB Controller USB Key board Support USB Mouse Support AC97 Audio Onboard Serial Port 1...
  • Page 34 ATA33). FUSB Control ler Disable this option if you are not using the onboard U SB feature. Enabl e d USB Controller. (Default value) 8Enabled Disabl e d USB Controller. 8Disabled GA-8IE533 Motherboard - 30 -...
  • Page 35 F US B Keyboard S upport When a USB keyboard is installed, please set at Enabled. Enabled USB Key board Support. 8Enabled Disabled USB Key board Support. (Default value) 8Disabled F US B Mouse Support Enabl e d USB Mouse Support. 8Enabled Disabled USB Mouse Support.
  • Page 36 Enabl e Midi port and address is 300. 8300 Enabl e Midi port and address is 330.(Default Value) 8330 F Midi Port IRQ Midi Port use I R Q 5. Midi Port use IRQ10. (Default Value) GA-8IE533 Motherboard - 32 -...

  • Page 37: Power Management Setup

    Power Management Setup CMOS Setup Utili t y -Copy right (C) 1984-2002 Aw ard Soft w are Pow er Management Setup ACPI Suspend Ty pe Pow er LED in S1 State Soft - Off by PWR-BTTN PME Ev ent Wake Up ModemRingOn Resume by Al a rm ø...

  • Page 38: Acpi Suspend Type

    You can set "Resume by Alarm" item to enabled and key in Data/time to pow er on sy st e m. Disable this function. (Default Value) 8Disabled Enable alarm function to POWER ON sy stem. 8Enabled GA-8IE533 Motherboard - 34 -...
  • Page 39 If RTC Al a rm Lead To Pow er On is Enabl e d. Date ( of Month) Alarm : Time ( hh: mm: ss) Alarm : F Power On By Mouse Disabled this funct i on. (Default v alue) 8Disabled 8Mouse Cl i ck Set mouse double cl i ck to pow er on sy st e m.

  • Page 40: Pnp/Pci Configurations

    8Auto Set 3,4,5,7,9,10,11,12,15 to PCI3. 83,4,5,7,9.,10,11,12,15 FPCI4 IRQ Ass ignment Auto assign IRQ to PCI 4. (Def a ult v alue) 8Auto Set 3,4,5,7,9,10,11,12,15 to PCI4. 83,4,5,7,9.,10,11,12,15 GA-8IE533 Motherboard [Auto] Item Help [Auto] Menu Lev el [Auto] [Auto] F7:Optimized Defaults...

  • Page 41: Pc Health Status

    PC Health Status CMOS Setup Utili t y -Copy right (C) 1984-2002 Aw ard Soft w are PC Health Status Reset Case Open St a tus Case Opened VCORE Vcc18 +3.3V +12V Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning SYSTEM FAN Fai l Warning...

  • Page 42: Cpu Warning Temperature

    Fan Warning Function Disable. (Def a ult v alue) 8Disabled Fan Warning Function Enable. 8Enabled C SYSTEM FAN Fai l Warni ng Fan Warning Function Disable. (Def a ult v alue) 8Disabled Fan Warning Function Enable. 8Enabled GA-8IE533 Motherboard - 38 -...

  • Page 43: Frequency/Voltage Control

    Frequency/Voltage Control CMOS Setup Utili t y -Copy right (C) 1984-2002 Aw ard Soft w are Frequency/Voltage Control CPU Clock Ratio CPU Host Cl o ck Control øCPU Host Frequency (MHz) øFi x ed PCI/AGP Frequency Host / DRAM Clock ratio Memory Frequency (MHz) PCI / AGP Frequency (MHz) CPU Voltage Control...
  • Page 44 Increase DRAM v ol t age may get stabl e for Ov er_Clock. But i t may damage t o DRAM module w hen enable t h is feature. Supply v olt a ge as DRAM module reguired. (Def a ult v alue) 8Normal Set DIMM v ol t age from 2.6V~2.8V. 8+0.1V~+.03V GA-8IE533 Motherboard - 40 -...

  • Page 45: Top Performance

    Top Performance CMOS Setup Utili t y -Copy right (C) 1984-2002 Aw ard Soft w are }Standard CMOS Feat u res }Adv anced BI O S Feat u res }Integrated Peripherals Disabled... [ n }Pow er Management Setup Enabled...[ }PnP/PCI Configurations }PC Healt h Status hi: Mov e }Frequency/Voltage Control...

  • Page 46: Load Fail-Safe Defaults

    Figure 10: Load Fail-Safe Defaults F Load Fai l-Safe Defaul ts Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum sy stem performance. GA-8IE533 Motherboard Top Performance Load Fail-Safe Defaults Load Optimi z ed Defaults...

  • Page 47: Load Optimized Defaults

    Load Optimized Defaults CMOS Setup Utili t y -Copy right (C) 1984-2002 Aw ard Soft w are }Standard CMOS Feat u res }Adv anced BI O S Feat u res }Integrated Peripherals }Pow er Management Setup }PnP/PCI Configurations }PC Healt h Status }Frequency/Voltage Control ESC:Quit Load Optimized Defaults? ( Y/N) ?N...

  • Page 48: Set Supervisor/User Password

    Setup Menu. If you select “Setup” at “Security Option” in Advance BIOS Features Menu, you will be prompted only w hen you try to enter Setup. GA-8IE533 Motherboard Top Performance Load Fail-Safe Defaults...

  • Page 49: Save & Exit Setup

    Save & Exit Setup CMOS Setup Uti l ity -Copy right (C) 1984-2002 Aw ard Software }Standard CMOS Feat u res }Adv anced BI O S Feat u res }Integrated Peripherals }Pow er Management Setup }PnP/PCI Configurations }PC Healt h Status }Frequency/Voltage Control ESC:Quit Save to CMOS and EXIT (Y/N)? Y...

  • Page 50: Exit Without Saving

    Figure 14: Ex it Wit h out Sav ing Type “Y” will quit the Setup Utility without sav ing to RTC CMOS. Type “N” w ill return to Setup Utility. GA-8IE533 Motherboard Top Performance Load Fail-Safe Defaults Load Optimi z ed Defaults...

  • Page 51: Chapter 4 Technical Reference

    Chapter 4 Technical Reference Block Diagram AGP 4X AGPCLK (66MHz) 5 PCI AC97 CODEC PCICLK (33MHz) PCICLK (33MHz) USBCLK (48MHz) 14.318 MHz 33 MHz CPUCLK+/- (100/133MHz) Pentium 4 System Bus 400/533MHzHz 100/133 MHz DDR RAM Intel HCLK+/- (100/133MHz) 82845E MCHCLK (66MHz) 66 MHz 33 MHz 14.318 MHz...

  • Page 52: Bios Introduction

    BIOS directly. Or you may want to keep a backup for your current BIOS, just choose “ Save Current BIOS” to save it first. You make a wise choice to use Gigabyte, and @BIOS update your BIOS smartly. You are now worry free from updating wrong BIOS, and capable to maintain and manage your BIOS easily.

  • Page 53: Easy Tune

    "Overclock" technology toward to a newer generation. This wonderful software is now free bundled in Gigabyte motherboard attached in driver CD. Users may make a test drive of "EasyTune 4" to find out more amazing features by themselves.

  • Page 54: Bios Flash Procedure

    BIOS Flash Procedure Method 1: We use GA-7VTX motherboard and Flash841 BIOS flash utility as example. Please flash the BIOS according to the following procedures if you are now under the DOS mode. Flash BIOS Procedure: STEP 1: (1) Please make sure your system has installed the extraction utility such as winzip or pkunzip. Firstly you have to install the extraction utility such as winzip or pkunzip for unzip the files.
  • Page 55 (2) Select the "Quick (erase)" for Format Type, and pick both "Display summary when finished" and "Copy system files", after that press "Start". That will format the floppy and transfer the needed system files to it. Beware: This procedure will erase all the prior data on that floppy, so please proceed accordingly.
  • Page 56 STEP 3: Download BIOS and BIOS utility program. (1) Please go to Gigabyte website http://www.gigabyte.com.tw/index.html, and click "Support". (2) From Support zone, click the "Motherboards BIOS & Drivers". GA-8IE Motherboard - 52 -...
  • Page 57 (3) We use GA-7VTX motherboard as example. Please select GA-7VTX by Model or Chipset optional menu to obtain BIOS flash files. (4) Select an appropriate BIOS version (For example: F4), and click to download the file. It will pop up a file download screen, then select the "Open this file from its current location" and press "OK".
  • Page 58 (5) At this time the screen shows the following picture, please click "Extract" button to unzip the files. (6) Please extract the download files into the clean bootable floppy disk A mentioned in STEP 2, and press "Extract". GA-8IE Motherboard - 54 -...
  • Page 59 STEP 4: Make sure the system will boot from the floppy disk. (1) Insert the floppy disk (contains bootable program and unzip file) into the floppy drive A. Then, restart the system. The system will boot from the floppy disk. Please press <DEL> key to enter BIOS setup main menu when system is boot up.
  • Page 60 (3) Press "Enter" to enter "BIOS FEATURES SETUP" menu. Use the arrows to highlight the item "1st Boot Device", and then use the "Page Up" or "Page Down" keys to select "Floppy". AMIBIOS SETUP - BIOS FEATURES SETUP ( C ) 2001 American Megatrends, Inc. All Rights Reserved 1st Boot Device : Floppy 2nd Boot Device...
  • Page 61 STEP 5: BIOS flashing. (1) After the system boot from floppy disk, type "A:\> dir/w" and press "Enter" to check the entire files in floppy A. Then type the "BIOS flash utility" and "BIOS file" after A:\>. In this case you have to type "A:\>...
  • Page 62 (3) It will pop up a screen and asks "Are you sure to flash the BIOS?" Press [Enter] to continue theprocedure, or press [ESC] to quit. Beware: Please do not turn off the system while you are upgrading BIOS. It will render your BIOS corrupted and system totally inoperative.
  • Page 63 STEP 6: Load BIOS defaults. Normally the system redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the BIOS defaults after BIOS has been upgraded. This important step resets everything after the flash. (1) Take out the floppy diskette from floppy drive, and then restart the system. The boot up screen will indicate your motherboard model and current BIOS version.
  • Page 64 (3) Use the arrows to highlight the item "SAVE & EXIT SETUP" and press "Enter". System will ask "SAVE to CMOS and EXIT (Y/N)?" Press "Y" and "Enter" keys to confirm. Now the system will reboot automatically, the new BIOS setting will be taken effect next boot-up. AMIBIOS SIMPLE SETUP UTILITY - VERSION 1.24b (C) 2001 American Megatrends, Inc.
  • Page 65 Method 2: Q-Flash Introduction A. What is Q-Flash Utility? Q-Flash utility is a pre-O.S. BIOS flash utility enables users to update its BIOS within BIOS mode, no more fooling around any OS. B. How to use Q-Flash? a. After power on the computer, pressing <Del> immediately during POST (Power On Self Test) it will allow you to enter AWARD BIOS CMOS SETUP, then press <F8>...
  • Page 66 Load BIOS From Floppy !In the A:drive, insert the "BIOS" diskette, then Press Enter to Run. XXXX.XX Total Size: 1.39M F5: Refresh DEL: Delete Where XXXX.XX is name of the BIOS file. !Press Enter to Run. Are you sure to update BIOS? [Enter] to contiune Or [ESC] ot abort...

  • Page 67: Bios Flash Procedure

    Method 3: BIOS Flash Procedure BIOS update procedure: If you don’ t have DOS boot disk, we recommend that you used Gigabyte @BIOS flash BIOS. Press "Tools" icon. 1.Click "Gigabyte Utilities". Click here. Click "P". Methods and steps: I. Update BIOS through Internet a.
  • Page 68 Otherwise, your system won't boot. c. In method I, if the BIOS file you need cannot be found in @BIOS Gigabyte's web site for downloading and updating it according to method II. d. Please note that any interruption during updating will cause system unbooted...

  • Page 69: 4-/6-Channel Audio Function Introduction

    Revision History 2-/4-/6-Channel Audio Function Introduction The installation of windows 98SE/2K/ME/XP is very simple. Please follow next step to install the function! Stereo Speakers Connection and Settings: We recommend that you use the speaker with amplifier to acquire the best sound effect if the stereo output is applied.
  • Page 70 4 Channel Analog Audio Output Mode STEP 1 : Connect the front channels to “Line Out”,the rear channels to “Line In”. Line Out Line In STEP 2 : After installation of the audio driver, you ‘ ll find an icon on the taskbar’ s status area. Click the audio icon “...
  • Page 71 Basic 6 Channel Analog Audio Output Mode Use the back audio panel to connect the audio output without any additional module. STEP 1 : Connect the front channels to “ Line Out” ,the rear chan- nels to “ Line In” , and the Center/Subwoofer channels to “...
  • Page 72 Advanced 6 Channel Analog Audio Output Mode (using SURROUND-KIT): “ SURROUND-KIT” is an optional device, which access analog output to rear channels and Center/Subwoofer channels. It is the best solution if you need 6 channel output, Line In and MIC at the same time. STEP 1 : Insert the “...
  • Page 73 STEP 3 : Connect the front channels to back audio panel’ s “ Line Out” , the rear channels to SURROUND-KIT’ s REAR R/L, and the Center/Subwoofer channels to SURROUND-KIT’ s SUB CENTER. STEP 4 : Click the audio icon “ Sound Effect” from the windows tray at the bottom of the screen.
  • Page 74 SPDIF Output Device (Optional Device) A “SPDIF output” device is available on the motherboard. Cable with rear bracket is provided and could link to the “SPDIF output” connector (As picture.) For the further linkage to decoder, rear bracket provides coaxial cable and Fiber con- necting port.

  • Page 75: Chapter 5 Appendix

    Chapter 5 Appendix Revision History Picture below are shown in Windows XP (IUCD driver version 2.11) Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe.
  • Page 76 CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. 1.Click "Intel Chipset Software Installation Utility" item. 3.Click "Yes". GA-8IE533 Motherboard 2.Click "Next". 4.Click "Next". 5.Click "Finish" to restart computer. - 72 -...
  • Page 77 A-2: Intel Application Accelerator: Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. 1.Click "Intel Application Accelerator".
  • Page 78 2.Click "Close" to restart computer. If there is any problem occurred during USB2.0 device installing, using or upgrading. Please visit Microsoft or GIGABYTE website for downloading the latest drivers. A-4. USB Patch Driver Enable S3 for USB Device Setup is preparing the InstallShield(R) Wizard which will guide you through the setup process.
  • Page 79 Revision History Appendix B: RealTek AC'97 Audio Driver Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. Press "Audio"...
  • Page 80 Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. Press "Tools" icon. 1.Click "Gigabyte Utilities". 3.Click "Next". GA-8IE533 Motherboard 2.Click "Easy Tune 4".
  • Page 81 Acronyms Acronyms Meaning ACPI Advanced Configuration and Power Interface Advanced Power Management Accelerated Graphics Port Audio Modem Riser Advanced Communications Riser BIOS Basic Input / Output System Central Processing Unit CMOS Complementary Metal Oxide Semiconductor CRIMM Continuity RIMM Communication and Networking Riser Direct Memory Access Desktop Management Interface DIMM...
  • Page 82 Network Interface Card Operating System Original Equipment Manufacturer PCI A.G.P. Controller POST Power-On Self Test Peripheral Component Interconnect RIMM Rambus in-line Memory Module Special Circumstance Instructions SECC Single Edge Contact Cartridge SRAM Static Random Access Memory GA-8IE533 Motherboard - 78 -...
  • Page 83 Technical Support/RMA Sheet Customer/Country: Company: Contact Person: E-mail Add. : Model name/Lot Number: BIOS version: O.S./A.S.: Hardware Mfs. Model name Configuration Memory Brand Video Card Audio Card CD-ROM / DVD-ROM Modem Network AMR / CNR Keyboard Mouse Power supply Other Device Problem Description: Phone No.: PCB revision:...
  • Page 84 GA-8IE533 Motherboard - 80 -...
  • Page 85 - 81 - Memo...
  • Page 86 GA-8IE533 Motherboard - 82 -...
  • Page 87 - 83 - Memo...
  • Page 88 GA-8IE533 Motherboard - 84 -...
  • Page 89 - 85 - Memo...
  • Page 90 GA-8IE533 Motherboard - 86 -...
  • Page 91 - 87 - Memo...
  • Page 92 GA-8IE533 Motherboard - 88 -...
  • Page 93 - 89 - Memo...
  • Page 94 GA-8IE533 Motherboard - 90 -...
  • Page 95 - 91 - Memo...
  • Page 96 GA-8IE533 Motherboard - 92 -...

Table of Contents