All specifications are nominal and may change as design installed and used in accordance with the instruction improvements occur. Greenlee Tools, Inc. shall not be liable for manual, may cause harmful interference to radio com- damages resulting from misapplication or misuse of its products.
• Keep hands away from the crimp- ing tool head when crimping. Failure to observe these warnings could result in severe injury or death. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
Page 4
Failure to observe these precautions may result in injury or property damage. Note: Keep all decals clean and legible, and replace when necessary. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
350 kcmil aluminum splices, 750 kcmil aluminum terminals * Do not use non-butting dies (crimps controlled by tonnage) in this tool, as damage could occur to connectors and/or conductors. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
DIE HOLDER ASSEMBLIES TOP DIE HOLDER RETAINING SPRING PLUNGER (6) RETAINING SPRING PLUNGER (6) PH2 Die Holder Kit 48824 contains: (1) 48823 and (2) 48825 Die Holders Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
Page 7
RETAINING SPRING PLUNGER (6) 48788 Die Holder Kit contains: 48820 Die Holder Kit contains (1) each: (2) 48789 Die Holders 48822 Upper Die Holder and 48821 Lower Die Holder Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
RETAINING SPRING temperature. PLUNGERS (6) DIE RETAINING MECHANISMS TOP DIE HOLDER RETAINING SPRING PLUNGER (6) 12-Ton “U” Die Holder Kit 48802 contains: (2) 48803 Die Holders Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
Send tool in for service at end of cycle * Running the battery below 16 V can damage the battery. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
Page 10
Failure to observe these warnings could result in severe injury or death. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
ACL/ACN 60176; column instead of the 400 to Aluminum VACL BLUA YA-ATN 2ACL/2ACN 60230 to number provided with 750 kcmil: Lugs ALNS/ALNN/ALND 60278 the connector. 3 crimps Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
Tool deactivated Service necessary Real-time clock not found Bluetooth unit not found ® Pressure sensor not found Burst pressure exceeded Battery temperature too low Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
3. Inspect the rotation of the head assembly. Fully debris or hydraulic oil. retract the ram. The head should rotate no more than 360°. If damage is detected, contact Greenlee customer service at 800-435-0786 for warranty service or repair. After use: 1.
800-435-0786 for warranty service or repair. Air in hydraulic system. Pull trigger and hold retract button simultane- ously. Run for approximately 10 seconds, and then attempt to crimp. If unsuccessful, contact Greenlee customer service at 800-435-0786 for warranty service or repair. Cold oil.
Page 15
EK1550LX Battery-powered Crimping Tool Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...