Advertisement
The Bottom of Your Notebook Computer G-MAX N203
Ü 1.
Hard Disk Compartment
Open this cover of this compartment to replace with other Hard Disk
Drive.
Ü 2.
Battery Bay
Equipped with a choice of Lithium-Ion (Li-Ion) battery pack.
Ü 3.
Memory Compartment
Remove the screw to find one DIMM slot. One slot is empty for
upgrade usage.
Ü 4.
Battery Release Latch
Push the latch to the right end to remove the battery pack.
Removing the HDD & Installing PC Cards
Removing the HDD
Ü 1.
Remove the screws and open the cover by lifting its upper side cover.
Ü 2.
Take out the hard disk from the compartment by finger carefully.
Installing PC Cards
Ü
1. Locate the PC card slot cover on the left side of your notebook
computer G-MAX N203.
Ü
2. Insert the side of PC card with the 68-pin socket into the PCMCIA slot.
The face label of the card should also be facing up.
Ü
3. When the full length of the card is almost inside the slot, push firmly
but slowly, to ensure full connection with the computer. The PC card will
be detected and once the needed driver is installed, it will generate a
beep
sound to indicate that the card is detected.
6
TM
The Quick Steps to Set Up Notebook Computer G-MAX N203
Plug the power cable
Ü
1. Plug the AC power cord into
the power socket of the AC power
adapter.
Ü
2. Plug the other end of the AC
power cord to a live AC wall
outlet.
Ü
3. Plug the connector of the AC
adapter to the DC-IN port found
at the left of your notebook
Open the display
Ü
1. Facing the Front side of your
notebook computer G-MAX N203,
locate the latch on the center of
the display panel.
Ü
2. Push the display latch and
raise the panel.
Ü
3. Adjust the display to
comfortable viewing angle.
Turning on your G-MAX N203
Ü
1. Open the display panel.
Ü
2. Turn on your notebook computer
G-MAX N203 by momentarily
pressing then releasing the power
button.
When you release power on / resume
button, the Power LED on the system
indicator panel comes on.
9
Installing Your G-MAX N203's Device Drivers
If you already have an operating system installed into your notebook
computer G-MAX N203, it is best to install the needed device drivers for
using the built-in devices of your notebook computer G-MAX N203. Before
installing the drivers, check with your dealer first if they have already
installed all the drivers along with the operating system. If not, follow the
procedures below:
Ü
1. You can find one bundled Driver CD shown as follow.
Ü
2. Put the CD into the CD R-W or DVD-RW (optional) Drive. It will get you
through the Auto Run installation.
TM
Lift the latch
10
TM
7
Removing Battery & Installing Memory Module
Remove the battery
Ü 1.
Sl
ide the related latch to left as the sequence shown in the figure
below.
Ü 2.
Gently pry the Battery Pack from the computer chassis.
Installing the memory module
Ü 1.
Remove the screw and open the DIMM cover by your finger.
Ü 2.
Locate the memory module into the empty memory module sockets.
(Your system comes with one memory module already installed in the
socket.)
How to Recover Your System
What is Xpress Recovery?
Xpress Recovery utility is an utility for backing up and restoring your
operating system partition.
Your hard drive must conform to the following specifications:
1. It supports FAT16 FAT32 NTFS Operation System.
2. It is not work when you install Boot Manager.
3. It must be used with IDE hard disk supporting HPA.
4. The first partition must be set as the boot Partition. When the boot
partition is backed up, please do not change the its size.
5. It must be connected to IDE1 Master.
Note:
1.System data and hard disk's reading/writing speed will affect backing
up speed.
2.This Recovery is not used when HDD crashed , please notify your
dealer immediately.
How to use the Xpress Recovery?
This utility will recover your system to factory default.
1. Press RECOVER to
recover your system.
The system will begin
restoring the image
to the original state.
2. Press EXIT to exit and
restart your notebook
computer G-MAX N203.
8
15 1 1
Advertisement
