Part Names - Onkyo TX-RZ1100-B Basic Manual

> Before start > Hookup > Setup
separate room or the ZONE Speaker, adjust with VOL+/–
on the remote controller. To control on the main unit,
press ZONE 2 or ZONE 3 and adjust with the MASTER
VOLUME control within 8 seconds.
0 The information for a connected device can be displayed
on the TV screen in a separate room. Press the
button while the remote controller is in the mode for
controlling ZONE 2.
0 Power consumption in standby mode increases when the
multi-zone function is being used.
To turn off the function
Press Í ON/STANDBY while in the mode for controlling
ZONE 2 or ZONE 3 on the remote controller.
Playing in ZONE 2 or ZONE 3 only
If you turn the unit to standby during multi-zone playback,
the Z2 or Z3 indicator is dimmed and the playback mode is
switched to playback in a separate room only. Setting
ZONE 2/ZONE 3 to on while this unit is in standby will also
switch the playback mode to the same setting.
WHOLE HOUSE MODE
If you press WHOLE HOUSE MODE while playback is
being performed in the main room, the WHOLE HOUSE
MODE is turned on, "Z2" and "Z3" on the display light at the
same time and the playback sources of all the rooms are
switched to the same source at once.
0 The sources that can be played in ZONE 2 can be played
in all rooms.
0 This function cannot be used if headphones are
connected or audio is output from the speakers of the TV.
Settings
Settings are required in Initial Setup, "4. Multi Zone Setup"
( ) to use the multi-zone feature. When checking the
P22
setting content, refer to the following, press
remote controller, and check in the Setup menu that is
displayed.
– When you have connected a TV in the separate room
with an HDMI cable, have you selected "Use" in "1. Input/
> Playback > Part Names
Output Assign" – "TV Out/OSD" – "Zone2 HDMI"?
– When you are playing the audio from an AV component
with an HDMI cable in the separate room, have you
selected "Use" in "1. Input/Output Assign" – "TV Out/
OSD" – "Zone2 HDMI"?
– When you have connected speakers in a separate room
with speaker cable, have you selected "Zone 2" or "Zone
2/Zone 3" in "2. Speaker" – "Configuration" – "Zone
Speaker"?
– When you have connected a power amplifier in a
separate room with an analog audio cable and you want
to control the volume with this unit, have you selected
"Variable" in "6. Multi Zone" – "Zone 2" or "Zone 3" –
"Output Level"?
on the
> Advanced Manual
Troubleshooting | Appendix
Others
To adjust the sound quality
It is possible to enhance or moderate the bass and treble
range of all channels except the subwoofer channel. Press
TONE on the main unit several times to select the desired
setting from "Bass" and "Treble", and turn the TONE dial to
adjust.
0 This cannot be set if the listening mode is Pure Audio,
Direct or THX.
0 You can also adjust the sound quality of a power
amplifier connected in a separate room. After pressing
either ZONE 2 or ZONE 3 on the main unit, within
8 seconds press TONE and turn the TONE dial to adjust.
Quick Menu
By pressing Q on the remote controller during play, you can
adjust frequently used settings, such as the sound quality,
using on-screen menus. Select the item with the cursors of
the remote controller and press ENTER to confirm your
selection. To return to the previous screen, press
Quick Menu
Tone Bass
Level Treble
AccuEQ
Other
0 You can adjust the sound quality with "Tone". "Other"
includes settings such as "A/V Sync" that allows you to
adjust the audio delay when the video is behind the
audio, "Music Optimizer" that provides better sound
quality for compressed audio, and "HDMI Out" which
allows you to select the HDMI OUT terminal to output
from "MAIN", "SUB", and "MAIN+SUB".
.
BD/DVD
27