1. Manuals
  2. Brands
  3. Jonsered Manuals
  4. Chainsaw
  5. CS2258 Li
  6. Operator's manual

Jonsered CS2258 Li Operator's Manual

Hide thumbs Also See for CS2258 Li:
Table of Contents

Advertisement

Quick Links

CS2258 Li
EN
Operator's manual
2-21
BCS58VJN

Advertisement

Table of Contents
loading

Related Manuals for Jonsered CS2258 Li

Summary of Contents for Jonsered CS2258 Li

  • Page 1 CS2258 Li Operator's manual 2-21 BCS58VJN...

  • Page 2: Table Of Contents

    Contents INTRODUCTION............2 TROUBLESHOOTING..........17 SAFETY................4 TECHNICAL DATA............19 ASSEMBLY..............10 ACCESSORIES............20 OPERATION..............11 CONTENTS OF THE EC DECLARATION OF CONFORMITY..............20 MAINTENANCE............14 INTRODUCTION Operator's manual The initial language of this operator's manual is English. Operator's manuals in other languages are translations from English. Overview 1.
  • Page 3 23. Chain oil tank 24. Battery release button 25. Operator's manual Electrical shock Symbols on the product Chain direction Guide bar length Warning Locked Read this manual. Unlocked Use approved head protection. Guaranteed sound power level This product agrees with the applicable EC Use approved hearing protection.

  • Page 4: Safety

    SAFETY Safety definitions parts. Damaged or entangled cords increase the risk of electric shock. The definitions below give the level of severity for each • When operating a power tool outdoors, use an signal word. extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
  • Page 5 power tools. Such preventive safety measures configuration increases the risk of personal injury reduce the risk of starting the power tool and should never be done. accidentally. • Hold the power tool by insulated gripping surfaces • Store idle power tools out of the reach of children only, because the saw chain may contact hidden and do not allow persons unfamiliar with the power wiring or its own cord.
  • Page 6 Pinching the saw chain along the top of the guide bar • Remove the battery pack before you assemble the may push the guide bar rapidly back towards the product, put the product into storage or do operator. maintenance. • Do not use the product if it is changed from its initial Either of these reactions may cause you to lose control specification.
  • Page 7 • Make sure that you are always in control of the product. • The product must be operated with two hands. Do not operate the product with one hand. Serious injury to the operator, workers, bystanders, or a combination of these persons can result from operation with only one hand.
  • Page 8 • Always keep correct footing and operate the product only on safe and level surfaces. Slippery or not • Rotational Kickback can occur when the moving stable surfaces, such as ladders, can cause a loss of chain touches an object at the top of the guide balance or control.
  • Page 9 • Obey the sharpening and maintenance instructions by the manufacturer for the saw chain. • Only use replacement guide bars and saw chains specified by the manufacturer. • The risk of kickback is increased if the depth gauge is set too large. Personal protective equipment •...

  • Page 10: Assembly

    Safety instructions for maintenance • Regularly examine the battery pack charger and the battery pack for damage. Damaged or changed • Remove the battery pack before doing maintenance battery packs can cause a fire, explosion or risk of on the product. injury.

  • Page 11: Operation

    2. Pull the front hand guard rearward in the direction of 11. Tighten the saw chain by turning the chain tension the front handle to disengage the chain brake. knob clockwise. Tighten the saw chain until it does not sag from below the guide bar, but you can turn it 3.
  • Page 12 To fell a tree • The power meter shows the saw chain efficiency. If the saw chain efficiency is too low, the 2 lights on the 1. Remove dirt, stones, loose bark, nails, staples and left side of the power meter will be on. If the saw wire from the tree.
  • Page 13 To buck a log 5. As the felling back cut nears the hinge, the tree starts to fall. Make sure that the tree can fall in the correct direction and not rock rearward and pinch the saw chain. Stop the cut before the felling back cut is CAUTION: Do not let the saw chain touch complete to prevent this.

  • Page 14: Maintenance

    To change the power mode The number of LEDs that are on show the current charge level of the battery pack. The power mode of the product can be changed while LED lights Battery status the product is in operation. There are 2 power modes: All Green LEDs Fully Charged (100% - 76%) 1.
  • Page 15 • File position • Round file diameter • Clean the air intake of the motor housing. • Make sure that the nuts and screws are tight. • Make sure that the power switch works correctly. To sharpen the saw chain The cutter To sharpen the cutting teeth The cutter is the cutting part of the saw chain and has a...
  • Page 16 2. Use the flat file on the top of the depth gauge that extends through the depth gauge tool. The depth gauge is adjusted correctly when there is no resistance as the file is pulled along the depth gauge tool. Note: These recommendations are for when the length of the cutting teeth has not been significantly decreased.

  • Page 17: Troubleshooting

    2. Lift the top of the guide bar and extend the saw 4. Make sure that you can pull the saw chain around chain by turning the chain tension knob clockwise. freely by hand and that it does not hang down. Tighten the saw chain until it does not hang from the bottom of the guide bar.
  • Page 18 Problem Possible cause Solution Motor operates, chain rotates Chain is not sharp. Sharpen the chain. but does not cut Chain installed in the incorrect Reverse the direction of the chain. direction. Error codes The error codes help you do troubleshooting on the battery pack and/or the battery charger while it charges.

  • Page 19: Technical Data

    TECHNICAL DATA unit CS2258 Li (BCS58VJN) Motor specifications Motor type Brushless Motor voltage V (DC) Motor power 2000 Battery and charger specifications Default battery pack type 280Li Default battery charger type 440Ci Noise and vibration data Equivalent vibration level (ahv, eq) left handle 1.430...

  • Page 20: Accessories

    CS2258 Li (BCS58VJN) Thickness of drive links (gauge) mm (in.) 1.1 (0.043) Type of drive sprocket Spur Number of drive sprocket teeth ACCESSORIES Guide bar and saw chain combinations Guide bar Saw chain Length - cm (in) Pitch - mm (in) Gauge - mm (in) Max.
  • Page 21 The type examination certificate, in accordance with Annex IX, as provided in the signed Declaration of Conformity, is applicable to all manufacturing locations and Countries of Origin, as stated on the product. This chainsaw conforms to the example that underwent EC type examination.
  • Page 22 666 - 002 - 18.05.2018...
  • Page 23 666 - 002 - 18.05.2018...
  • Page 24 Original instructions 115990426 2018-05-18...

This manual is also suitable for:

Bcs58vjn

Table of Contents