Char-Broil CB600X 10201597-50 Product Manual page 8

Ignitor Lighting
• Do not lean over appliance while lighting.
1. Turn ON LP gas cylinder.
2. Open the Smoke Chamber door.
3. Press and turn the control knob to HIGH.
4. Turn ROTARY IGNITOR knob rapidly.
5. Pull out the Firebox Drawer to verify that the burner is lit.
6. If ignition does not occur in 5 seconds, turn the burner control
knob OFF, wait 5 minutes, and repeat lighting procedure.
If ignition still does not occur, follow match-lighting
instructions.
WARNING
Turn control knob and LP cylinder OFF when not in
use.
CAUTION
If ignition does NOT occur in 5 seconds, turn the
control knob OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Match-Lighting
Do not lean over appliance while lighting.
1. Turn ON LP cylinder.
2. Open the Smoke Chamber door.
3. Place lit match into match lighting hole of appliance as
pictured below. Make sure lit match is placed inside hole and
near burner.
4. Push in and turn control knob to HIGH.
lights and stays lit.
5. Pull out the Firebox Drawer to verify that the burner is lit.
First - Open
the door
Firebox
Drawer
Control
Knob
View is from side of
8 • 10201597-50
Be sure burner
Match
Lighting
Hole
Match
appliance
Burner Flame Check
• Light burner, rotate knob from HIGH to LOW. Looking through
the match light holes underneath the appliance, you should see
the flame height decrease when turning knob from HIGH to
LOW. Always check flame prior to each use. If only low flame
is seen refer to "Sudden drop or low flame" in the
Troubleshooting Section.
Turning Appliance Off
• Turn control knob to OFF
turning hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Turn ignitor knob. "Click" should
be heard each time at electrode. See "Troubleshooting" if no
click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valve. Knob locks in
first push in knob and release, knob should spring back. If knob
does not spring back, replace valve assembly before using Oil-
less Fryer. Turn knob to HIGH position then turn back to
position. Valve should turn smoothly.
Hose Check
• Before each use, check to see if hose is cut, worn or kinked.
Replace damaged hose before using applaince. Use only
valve/hose/regulator specified by manufacturer.
Normal
Hose
General Appliance Cleaning
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors are not painted at the factory (and
should never be painted). Apply a strong solution of detergent
and water or use a grill cleaner with scrub brush on insides of
appliance lid and bottom. Rinse and allow to completely air dry.
Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Plastic parts: Wash with warm soapy water and wipe dry.
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Painted surfaces: Wash with mild detergent or non-abrasive
cleaner and warm soapy water. Wipe dry with a soft non-
abrasive cloth.
• Stainless steel surfaces: To maintain the high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
position. Turn LP cylinder off by
OFF position. To check valve,
Kinked
Hose
OFF