Onkyo TX-SR494DAB Instruction Manual page 77

„ 3. Distance
Set the distance from each speaker to the listening position.
Setting Item Default Value
Front Left 3.60 m
Center 3.60 m
Front Right 3.60 m
Height Left 2.70 m
Height Right 2.70 m
Surround Right 2.10 m
Surr Back Right 2.10 m
Surr Back Left 2.10 m
Surround Left 2.10 m
Subwoofer 3.60 m
• The unit of distance can be changed by pressing the MODE button on the remote
controller. When using the unit "feet", the setting is available in increments of 0.1 ft from
0.1 ft to 30.0 ft. When using the unit "meter", the setting is available in increments of
0.03 m from 0.03 m to 9.00 m.
Setting Details
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Specify the distance between each speaker and
the listening position.
Contents Connections
≫
„ 4. Level Calibration
Adjust the volume level of each speaker.
Setting Item Default Value
Front Left 0 dB
Center 0 dB
Front Right 0 dB
Height Left 0 dB
Height Right 0 dB
Surround Right 0 dB
Surr Back Right 0 dB
Surr Back Left 0 dB
Surround Left 0 dB
Subwoofer 0 dB
77
Front Panel≫ Rear Panel≫ Remote≫
Playback Setup
≫ ≫
Setting Details
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-12 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
Select a value between "-15 dB" and "+12 dB"
(in 1 dB increments). A test tone will be output each
time you change the value. Select the desired level.
≫