Table of Contents
Advertisement
10" CABINET TABLE SAWS
WITH RIVING KNIFE
09/2013
OPTIONAL
KC-10JCS/J52 shown here with
MODEL:
optional 33 1/4" laminated
KC-10JCS/J52
melamine extension table and 2
sturdy adjustable supporting legs
(52" Max Rip)
(mod. EXT-5052)
Left Tilt
MODEL:
KC-10JCS/J30
(30" Max Rip)
INSTRUCTION MANUAL
COPYRIGHT © 2010 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
Advertisement
Table of Contents
Related Manuals for King Industrial KC-10JCS
Summary of Contents for King Industrial KC-10JCS
- Page 1 10” CABINET TABLE SAWS WITH RIVING KNIFE 09/2013 OPTIONAL KC-10JCS/J52 shown here with MODEL: optional 33 1/4” laminated KC-10JCS/J52 melamine extension table and 2 sturdy adjustable supporting legs (52” Max Rip) (mod. EXT-5052) Left Tilt MODEL: KC-10JCS/J30 (30” Max Rip) INSTRUCTION MANUAL COPYRIGHT ©...
-
Page 2: Warranty Information
WARRANTY INFORMATION 2-YEAR KING CANADA TOOLS LIMITED WARRANTY OFFERS A 2-YEAR LIMITED WARRANTY FOR THIS 10” CABINET SAW FOR INDUSTRIAL USE. PROOF OF PURCHASE Please keep your dated proof of purchase for warranty and servicing purposes. REPLACEMENT PARTS Replacement parts for this product are available at our authorized King Canada service centers across Canada. LIMITED TOOL WARRANTY King Canada makes every effort to ensure that this product meets high quality and durability standards. -
Page 3: General Safety Instructions For Power Tools
GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS 1. KNOW YOUR TOOL watch) because they could get caught in moving parts. Non-slip Read and understand the owners manual and labels affixed to footwear is recommended. Wear protective hair covering to the tool. Learn its application and limitations as well as its contain long hair. -
Page 4: Specifications Chart
GETTING TO KNOW YOUR 10” TABLE SAW AND SPECIFICATIONS Model KC-10JCS/J52 shown here with optional melamine extension table mod. EXT-5052 1. 4” Dust chute 11. Support legs/adjustable feet (Optional accessory EXT-5052) 2. Emergency stop 12. Motor access door 3. Switch with reset button 13. - Page 5 ELECTRICAL REQUIREMENTS & SWITCH OPERATION WARNING! ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE MACHINE DISCONNECTED FROM THE POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! PROPERLY POWER SUPPLY (240V) GROUNDED OUTLET...
- Page 6 ASSEMBLY DISASSEMBLING MOTOR BRACKET For shipping purposes, a motor bracket (A) Fig.5 is bolted to the cabinet and attached to the motor mount. This motor bracket must be removed before assembling, adjusting or operating this cabinet saw. You should keep this motor bracket for shipping or transporting your cabinet saw.
-
Page 7: Installing Rear Rail
Once both rails are installed, place the optional laminated extension table (F) Fig.9 between the front and rear rails (KC-10JCS/J52 Only). Fix it in place using hex. bolts, washers, spring washers and hex. nuts. Before securing it in place, adjust it up or down to ensure the top of the laminated extension table is set flush with the top of the right side extension wing (E). -
Page 8: Installing / Changing Blade
ASSEMBLY INSTALLING / CHANGING BLADE 1. Make sure the cabinet saw is Off and the power cord is disconnected. 2. If you are replacing a blade, raise the saw blade to its maximum height and lock the saw at 0 degrees. Remove the table insert. 3. -
Page 9: Blade Raising And Tilting Mechanism
ADJUSTMENTS ASSEMBLING BLADE GUARD/RIVING KNIFE Non through-cut operations- For non through-cut operations with a 10” blade, the riving knife (A) Fig.16 must be installed. The riving knife gets installed the same way as the blade guard splitter, see Through-cut operations instructions. For safety reasons, the highest point of the riving knife (A) Fig.16 should never exceed the highest point of the blade teeth, generally 1/8”... -
Page 10: Aligning Table T-Slot Parallel With Blade
ADJUSTMENTS ALIGNING TABLE T-SLOT PARALLEL WITH BLADE The table T-slot must be aligned parallel with the blade. Using a combination square (A) Fig.21, measure the distance from the back edge of the blade to the table T-slot. Pivot blade forward 180º and remeasure the distance using the exact same point on the blade. -
Page 11: Adjusting 45 And 90 Degree Positive Stops
ADJUSTMENTS & OPERATION ADJUSTING 45 AND 90 DEGREE POSITIVE STOPS The blade tilting mechanism of your saw is equipped with a positive stop at 45 and 90 degrees. To check and adjust these positive stops, proceed as follows: 1. Raise the saw blade to its maximum height. 2. -
Page 12: Operation
OPERATION RIPPING Ripping is the operation of making a lengthwise cut through a board, as shown in Fig.27, and the rip fence is used to position and guide the work. One edge of the work rides against the rip fence while the flat side of the board rest on the table. Since the work is pushed along the fence, it must have a straight edge and make solid contact with the table. -
Page 13: Maintenance & Optional Accessories
OPTIONAL ACCESSORIES Sliding Table Attachment Router Table Attachment model KST-101 (Fig.33) model KRT-100 (Fig.32) FIGURE 32 FIGURE 33 These optional accessories are designed to fit table saw model KC-10JCS and also fit most table saws having a 27” deep table. -
Page 14: Troubleshooting
TROUBLESHOOTING PROBLEM SOLUTION SAW WILL NOT START 1. Saw not plugged in. 1. Plug in saw. 2. Fuse blown or circuit breaker tripped. 2. Replace fuse or reset circuit breaker. 3. Cord damaged. 3. Have cord replaced by a certified electrician. OVERLOAD KICKS OUT FREQUENTLY 1.