Table of Contents
Advertisement
Available languages
Available languages
INSTALL GREASE FILTERS
Grease filters are located on the underside of microwave oven. For
installation instructions, see the User Manual packed with the microwave.
a
d
METHOD B - OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
IMPORTANT:
•
Make sure the screws for the blower motor and blower plate are securely
tightened when they are reinstalled. This will help avoid excessive vibration.
•
Make sure the motor wiring has been properly routed and secured, and that
the wires are not pinched.
CREATE REAR WALL EXHAUST OPENING
1.
Read the instructions on the Mounting Plate/Rear Wall template.
2.
Tape the Mounting Plate/Template to the rear wall, aligning it with the holes
previously drilled for holes A and B in the mounting plate.
3.
Cut the opening, following the instructions on the Rear Wall template.
REMOVE THE BLOWER PLATE
1.
Remove and save the screw(s) fastening the blower plate to the microwave.
2.
Lift off the blower plate.
b
c
NOT E:
IT IS VER
REA D
AND FOL
Y IMP
IN THE
ORT ANT
INST ALL
LOW THE
TO
BEF ORE
DIR ECT
ATIO N
ION S
REA R
PRO CEE
INST RUC
WAL L
DIN G
TION S
This Rear
TEM PLA
WIT H
THIS
Wall Temp
TE.
3/8" TO EDGE
moun ting
late serve
outlet .
plate and
s to positi
12"
to locate
on the
1. Use
a level
the horizo
bottom
to check
ntal exhau
accur ately.
that the
st
2. Locat
e and mark
templ ate
right side
is positi
oned
of the cente
at least
one stud
on the
4"
screw moun
It is impor
rline.
left or
tant to
use at
of the micro
ted firmly
least one
locati ons
wave . Mark
in a stud
to suppo
wood
for the
two additi
rt the weigh
3. Drill
holes in
suppl ied
onal, evenl
t
a stud,
the marke
toggle
bolts.
y space
drill a 3/16"
d locati
d
that do
hole for
ons. Wher
toggle
not line
up with
wood screw
e there
bolts.
a stud,
s. For holes
is
drill 5/8"
AT THIS
DO NOT
holes for
TIME .
INST ALL
4. Remo
THE MOU
5. Revie
ve the
templ ate
NTIN G
PLAT E
w the Instal
from the
instal lation
lation Instru
rear wall.
situat ion.
ction book
for your
Darle vuelt
versi ón
a a la hoja
en Espa
para cons
ñol.
ultar la
Loca te
and mar
k hole s
mou nting
to align
plate .
IMP ORT
with hole
ANT :
s in the
LOC ATE
AT LEA
THE CEN
ST ONE
TER LINE
STU D
MAR K
ON EITH
THE LOC
.
ER SIDE
SPA CED
ATIO N
OF
TOG GLE
FOR 2
ARE A.
BOL TS
ADD ITIO
IN THE
NAL , EVE
MOU NTIN
NLY
G PLA
TE
Trim the
rear wall
tem plat
e alon
g the dott
ed line
.
Loca te
mou nting
IMP ORT
LOC ATE
THE CEN
MAR K
SPA CED
ARE A.
Trim the
rear wall
tem plat
e alon
g the dott
ed line
.
and mar
k hole s
to align
plate .
with hole
s in the
ANT :
AT LEA
ST ONE
TER LINE
STU D
.
ON EITH
THE LOC
ER SIDE
ATIO N
FOR 2
OF
TOG GLE
ADD ITIO
BOL TS
NAL , EVE
IN THE
MOU NTIN
NLY
G PLA
TE
16
Surface Lights
A
Door
B
Grease Filters
C
Advertisement
Chapters
Table of Contents
