Related Manuals for Philips Saeco Intelia HD8753
Summary of Contents for Philips Saeco Intelia HD8753
- Page 1 Register your product and get support at www.philips.com/welcome Type HD8753 USER MANUAL PLEASE READ THIS USER MANUAL CAREFULLY BEFORE USING THE MACHINE.
- Page 2 IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid.
- Page 3 CAUTION This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user.
-
Page 4: Table Of Contents
Congratulations on your purchase of a Saeco Intelia One Touch Cappuccino full automatic espresso machine! To fully benefi t from the support that Saeco off ers, please register your product at www.philips.com/welcome. This user manual applies to HD8753. The machine is suitable for preparing espresso coff ees using whole coff ee beans. - Page 5 ENGLISH CAPPUCCINO BREWING ...................27 Adjusting the cappuccino lenght ......................28 HOT MILK BREWING ..................30 Adjusting the hot milk lenght .........................31 HOT WATER DISPENSING .................32 CLEANING AND MAINTENANCE ................34 Daily cleaning of the machine .........................34 Daily cleaning of the water tank......................36 Daily cleaning of the milk carafe ......................36 Weekly cleaning of the machine ......................37 Weekly cleaning of the milk carafe......................37 Weekly cleaning of the brew group ......................42...
-
Page 6: Important
• Do not make any modifi cations to the machine or its mains cord. Only have repairs carried out by a service centre authorized by Philips to avoid a hazard. • This machine is not intended for use by persons (including children) -
Page 7: Caution
ENGLISH Caution • The machine is for household use only. It is not intended for use in en- vironments such as staff kitchens of shops, offi ces, farms or other work environments. • Always put the machine on a fl at and stable surface. •... -
Page 8: Installation
INSTALLATION Product overview 12 13... -
Page 9: General Description
ENGLISH General description 1. Grinder adjustment knob 2. Pre-ground coff ee compartment 3. Coff ee bean hopper 4. Coff ee bean hopper lid 5. Control panel 6. Dispensing spout 7. Full drip tray indicator 8. Cup holder grill 9. Drip tray 10. -
Page 10: Preparing For Use
ENGLISH PREPARING FOR USE Machine packaging The original packaging has been designed and constructed to protect the machine during transport. We recommend keeping the packaging material for possible future transport. Machine installation Remove the drip tray with grill from the packaging. Remove the machine from the packaging. - Page 11 ENGLISH Remove the water tank. Rinse the water tank under fresh water. Fill the water tank with fresh water up to the MAX level and reinsert it into the machine. Make sure it is fully inserted. Caution: Never fi ll the water tank with warm, hot, sparkling water or any other liquid, as this may cause damage to the water tank and the machine.
-
Page 12: Using The Machine For The First Time
ENGLISH Switch the power button to “I” to turn on the machine. The display shows the stand-by icon. To turn on the machine, simply press the “ ” button. The display indi- cates that the circuit must be primed. USING THE MACHINE FOR THE FIRST TIME When using the machine for the fi rst time, the following activities need to happen: 1) You need to prime the circuit... -
Page 13: Automatic Rinse/Self- Cleaning Cycle
ENGLISH Press the “ ” button to start the cycle. The machine starts the auto- matic priming of the circuit by dispensing some water through the dispensing spout. The bar under the icon shows the operation progress. When the pro- cess is completed, the machine stops dispensing automatically. -
Page 14: Manual Rinse Cycle
ENGLISH Manual rinse cycle During this process you activate the coff ee brewing cycle and fresh water fl ows through dispensing spout. This takes a few minutes. Place a container under the dispensing spout. Check that the machine shows this display. Select the pre-ground coff ee brewing function by pressing the “... - Page 15 ENGLISH The following icon is displayed. Press the “ ” button to start dispensing hot water. This icon is displayed. The machine reminds you to install the water dis- pensing spout. Check that it is correctly installed. Press “ ” to confi rm. The machine will start dispensing hot water.
-
Page 16: Measuring And Programming Water Hardness
ENGLISH Measuring and programming water hardness Measuring water hardness is very important for defi ning the frequency in which the machine has to be descaled and to install the “INTENZA+” water fi lter (for more detail on the water fi lter see next chapter). To measure the water hardness follow the steps below: Immerse the water hardness test strip (supplied with the machine) in water for 1 second. -
Page 17: Intenza+" Water Fi Lter Installation
ENGLISH Press the “ ” button to exit the programming menu. “INTENZA+” water fi lter installation We recommend you to install the “INTENZA+” water fi lter as this prevents lime scale to build up in your machine and preserves a more intense aroma to your espresso coff ee. -
Page 18: Replacing The "Intenza+" Water Fi Lter
ENGLISH Put the fi lter into the empty water tank. Press it until it cannot move further down. Fill the water tank with fresh water and reinsert it into the machine. Dispense the entire water tank by using the hot water function (see chapter “Hot water dispensing”. - Page 19 ENGLISH Press the “ ” button and scroll the pages by pressing the “ ” but- ton until the following icon is displayed. Select the “RESET” option. Press the “ ” button to confi rm. To exit, press the “ ”...
-
Page 20: Adjustments
ENGLISH ADJUSTMENTS The machine allows for certain adjustments so that you can brew the best tasting coff ee possible. Saeco Adapting System Coff ee is a natural product and its characteristics may change according to its origin, blend and roast. The machine is equipped with a self-adjusting system that allows the use of all types of coff ee beans available on the market (not for caramelized beans). -
Page 21: Adjusting The Aroma (Coff Ee Strength)
ENGLISH Press and turn the grinder adjustment knob one notch at a time. You will taste the diff erence after brewing 2-3 cups of espresso. The reference marks inside the coff ee bean hopper indicate the grind setting. There are 5 diff erent grind settings to choose from: 1 - Coarse grind: lighter taste, for dark roasted coff ee blends 2 - Fine grind: bolder taste, for light roasted coff ee blends When you adjust the ceramic coff ee grinder to a fi ner setting, your coff ee... -
Page 22: Adjusting The Dispensing Spout
ENGLISH Adjusting the dispensing spout The height of the dispensing spout can be adjusted to better fi t the dimen- sions of the cups that you wish to use. Move the dispensing spout up or down with your fi ngers to adjust its height as shown in the image. -
Page 23: Adjusting The Coff Ee Length
ENGLISH Adjusting the coff ee length The machine allows you to adjust the amount of brewed coff ee according to your taste and/or the size of your cups. Each time the “ ” or “ ” button is pressed, the machine brews a pre-set amount of coff ee. -
Page 24: Espresso And Coffee Brewing
ENGLISH ESPRESSO AND COFFEE BREWING Before brewing coff ee, make sure that there are no warnings shown on the display, and that both, water tank and coff ee bean hopper are fi lled. Espresso and coff ee brewing using coff ee beans Place 1 or 2 cups under the dispensing spout. -
Page 25: Espresso And Coff Ee Brewing Using Pre-Ground Coff Ee
ENGLISH Espresso and coff ee brewing using pre-ground coff ee This function allows to use pre-ground and decaff einated coff ee. With the pre-ground coff ee function you can only brew one coff ee at a time. Press the “ ”... -
Page 26: Milk Carafe
ENGLISH MILK CARAFE This chapter explains how to use a milk carafe to prepare a cappuccino or hot milk. Note: Before using the milk carafe, clean it thoroughly as described in the “Clean- ing and Maintenance” chapter. We recommend to fi ll it with cold milk (approx. 5°C). After use, put the carafe back in the refrigerator. -
Page 27: Inserting The Milk Carafe
ENGLISH Inserting the milk carafe If installed, remove the water dispenser as shown in the fi gure: Press the two buttons on the side to unlock it and lift it slightly; Pull the water dispenser to remove it. Open the milk carafe dispenser by turning it counter-clockwise until it locks into place. -
Page 28: Removing The Milk Carafe
ENGLISH Removing the milk carafe Rotate the carafe upwards until it releases from the insert in the drip tray. Pull away from the machine until it is completely detached. Close the milk carafe dispenser by turning it clockwise. Emptying the milk carafe Press the release buttons to allow the lid removal. -
Page 29: Cappuccino Brewing
ENGLISH CAPPUCCINO BREWING Warning: Danger of scalding! Dispensing may be preceded by short sprays of milk and steam. Risk of burning. Wait until the end of the cycle before removing the milk carafe . Fill the milk carafe with milk. The level must be between the minimum (MIN) and maximum (MAX) indication on the milk carafe. -
Page 30: Adjusting The Cappuccino Lenght
ENGLISH The following icon is displayed during pre-heating time required by the machine. When the machine shows the following icon, the machine pours a milk. The pouring can be stopped by pressing the “ ” button. Once the milk froth has been poured, the machine brews coff ee. The pouring can be stopped by pressing the “... - Page 31 ENGLISH Press and hold the “ ” button until the ‘MEMO’ icon appears on the display. Then release the button. The machine is now programming. The following icon is displayed during pre-heating time required by the machine. When the machine shows the following icon, the machine starts to pour milk froth into the cup When the desired milk froth quantity is reached, press the “...
-
Page 32: Hot Milk Brewing
ENGLISH HOT MILK BREWING Warning: Danger of scalding! Dispensing may be preceded by short sprays of milk and steam. Risk of burning. Wait until the end of the cycle before removing the milk carafe. Fill the milk carafe with milk. The level must be between the minimum (MIN) and maximum (MAX) indication on the milk carafe. -
Page 33: Adjusting The Hot Milk Lenght
ENGLISH The following icon is displayed during pre-heating time required by the machine. The machine pours a pre-defi ned amount of hot milk into the cup. The pouring can be stopped by pressing the “ ” button. Note: After using the milk carafe, clean it as described in the ‘Cleaning and Main- tenance’... -
Page 34: Hot Water Dispensing
ENGLISH The following icon is displayed during pre-heating time required by the machine. When the desired amount of hot milk is reached, press the “ ” but- ton. Now the hot milk is programmed. Every time it is pressed, the machine will brew the same amount of hot milk that was programmed. - Page 35 ENGLISH Place a container under the hot water dispenser. Press the “ ” button. The following icon is displayed. Press the “ ” button to start dispensing process. This icon is displayed. The machine reminds you to install the water dispenser.
-
Page 36: Cleaning And Maintenance
ENGLISH Pour the desired amount of hot water. To stop the hot water dispens- ing process press the “ ” button. CLEANING AND MAINTENANCE Daily cleaning of the machine Caution: Timely cleaning and maintenance of your machine is very important as it prolongs the life of your machine. - Page 37 ENGLISH Empty and clean the coff ee residues drawer located inside of the ma- chine. Open the service door, remove the drawer and empty the coff ee residues. Empty and clean the drip tray: Press the side buttons to allow tray removal Remove the drip tray Note: Perform this operation also when the full drip tray indicator is raised.
-
Page 38: Daily Cleaning Of The Water Tank
ENGLISH Daily cleaning of the water tank Remove the small white fi lter or the INTENZA+ water fi lter (if installed) from the water tank and wash it with fresh water. Put the small white fi lter back or the INTENZA+ water fi lter (if installed) in its housing by gently pressing and turning it at the same time. -
Page 39: Weekly Cleaning Of The Machine
ENGLISH Weekly cleaning of the machine Clean the seat of the drip tray. Clean the pre-ground coff ee compartment with the cleaning brush. Weekly cleaning of the milk carafe The weekly cleaning is more thorough as it removes any milk residues from the milk carafe dispenser. - Page 40 ENGLISH Attach the lid on the milk carafe; ensure it is locked into place. Remove the top and fi ll the milk carafe up to the MAX level with fresh water. Put the top back into the milk carafe. Open the milk carafe dispenser and insert the carafe into the machine. Place a container under the dispensing spout.
- Page 41 ENGLISH The following icon is displayed during pre-heating time required by the machine. Once the machine stops dispensing water, the cleaning is fi nished. Remove the milk carafe and empty it. Press the release buttons to remove the lid. Turn the milk carafe dispenser up to the ( ) reference mark. Lift the milk carafe dispenser to remove it from the lid.
- Page 42 ENGLISH Remove the dispenser ring (A) from the milk carafe dispenser. Press the button indicated with the arrow to unlock the lid. Detach the lid (B) from the milk carafe dispenser by pulling it down while slightly pressing on the sides. Pull the milk frothing device (C) upwards.
- Page 43 ENGLISH Remove the suction tube (E). Clean thoroughly all the parts with lukewarm water. Note: You can also clean these parts in the dishwasher. Reassemble the parts following the reverse order. Note: As explained at step 13, the dispenser can only be inserted into the lid, when it is in the reference ( ) position.
-
Page 44: Weekly Cleaning Of The Brew Group
ENGLISH Weekly cleaning of the brew group The brew group should be cleaned every time the coff ee bean hopper is fi lled or at least once a week. Turn off the machine by pressing the “ ” button and remove the plug from the socket. - Page 45 ENGLISH Let the brew group air-dry thoroughly. Thoroughly clean the inside of the machine using a soft, dampened cloth. Make sure the brew group is in the rest position; the two reference signs must match. If they do not match, proceed as described in step (9).
-
Page 46: Monthly Cleaning Of The Milk Carafe
ENGLISH Insert the coff ee residues drawer and close the service door. Insert the coff ee grounds drawer. Monthly cleaning of the milk carafe In the monthly cleaning cycle we use the “Saeco Milk Circuit Cleaner”to keep the entire circuit clean of milk residues. You can purchase separately the “Saeco Milk Circuit Cleaner”. - Page 47 ENGLISH Press the “ ” button. The following icon is displayed. Press the “ ” button to select hot milk. The following icon is displayed during pre-heating time required by the machine. Once the machine stops dispensing water, repeat steps 5 - 8 until the carafe is emptied.
-
Page 48: Monthly Lubrication Of The Brew Group
ENGLISH Once the machine stops dispensing water, repeat steps 12 -15 until carafe is emptied. Remove the milk carafe and the container from the machine. Repeat steps 10 - 16 one more time. Disassemble and wash the milk carafe as described in the “Weekly cleaning of the milk carafe”... - Page 49 ENGLISH Lubricate the shaft too. Insert the brew group in its seat until it locks into place. (see “Weekly cleaning of the brew group” chapter). Insert the coff ee residues drawer. Close the service door. Insert the coff ee grounds drawer.
-
Page 50: Monthly Cleaning Of The Brew Group With "Coff Ee Oil Remover
ENGLISH Monthly cleaning of the brew group with “Coff ee Oil Remover” Besides weekly cleaning, we recommend running this cleaning cycle with the “Coff ee Oil Remover” after approximately 500 cups of coff ee or once a month. This operation completes the maintenance process of the brew group. - Page 51 ENGLISH Press the “ ” button to start a coff ee brewing cycle. Wait until the machine automatically ends the dispensing process. Press the “ ” button to turn off the machine, and let the solution take eff ect for approximately 15 minutes. Empty the container and put it back.
-
Page 52: Monthly Cleaning Of The Coff Ee Bean Hopper
ENGLISH Monthly cleaning of the coff ee bean hopper Clean the coff ee bean hopper once a month when it is empty with a damp cloth to remove coff ee oil. Thereafter refi ll it with coff ee beans. DESCALING The descaling process takes approx. - Page 53 ENGLISH Insert the milk carafe empty. Remove the “INTENZA+” water fi lter from the water tank if it was installed. Press the “ ” button. Press the “ ” button until the following display is shown. Press the “ ” button to enter the descaling menu. Note: If you press the “...
- Page 54 ENGLISH Press the “ ” button to start the descaling cycle. The machine will start dispensing the descaling solution at intervals. The bar on the display shows the cycle progress. Note: The descaling cycle may be paused by pressing the “ ”...
- Page 55 ENGLISH When inserting the water tank into the machine, this icon is displayed. Press the “ ” button to start the rinsing cycle. When this icon is displayed, the water tank is empty. Repeat steps 13 – CALC 17. Then continue to step 19. CLEAN .
- Page 56 ENGLISH Place back the “INTENZA+” water fi lter into the water tank if it was installed. Note: At the end of the descaling cycle, wash the brew group as described in the “Weekly cleaning of the brew group” chapter. The two rinse cycles are performed in order to have the circuit cleaned with a preset amount of water to ensure proper machine performance.
-
Page 57: Programming
ENGLISH PROGRAMMING You can change some of the machine operating settings according to her/ his preferences. Adjustable parameters Coff ee temperature This function allows you to adjust the coff ee brewing temperature. Timer (stand-by) This function allows you to adjust the time until the machine will go into standby mode after the last brewing. -
Page 58: Programming Mode Example
ENGLISH Programming mode example In this example, it is shown how to program the display contrast. Proceed in the same way to program the other functions. The programming menu can only be accessed when the machine is on and shows this display. Press the “... - Page 59 ENGLISH When the display value is changed, the “OK” message appears. Press the “ ” button to confi rm the change. Press the “ ” button to exit the programming mode. Note: The machine will automatically exit the programming mode if you do not push any button for 3 minutes.
-
Page 60: Meaning Of The Display Symbols
ENGLISH MEANING OF THE DISPLAY SYMBOLS This machine is equipped with a colour-coded system to make the user’s understanding of the display signals easier. The icons are colour-coded according to the traffi c light principle. Ready Signals (Green Colour) The machine is ready to brew products. The machine is ready to brew pre-ground coff ee. - Page 61 ENGLISH Ready Signals (Green Colour) The machine is programming the amount of coff ee to be brewed. Coff ee brewing using pre-ground coff ee in progress. The machine is brewing cappuccino. The machine is programming the amount of milk to dispense for the cappuc- cino.
- Page 62 ENGLISH Warning Signals (Yellow Colour) The machine is heating-up to brew beverages or dispense hot water. The machine is heating-up during beverages programming. The machine performs the rinsing cycle. Wait until the machine has com- pleted the cycle. The machine needs the “INTENZA+” water fi lter to be replaced. The brew group is being reset due to machine reset.
- Page 63 Turn off the machine. After 30 seconds, turn it on again. Try this 2 or 3 times. If the machine does not start, contact the Philips SAECO hotline in your country. You can fi nd its contact details in the warranty booklet by-packed...
-
Page 64: Troubleshooting
If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Philips Saeco hotline in your country. You fi nd its contact details in the warranty booklet by-packed separately or on www.philips.com/support. - Page 65 ENGLISH Machine actions Causes Solutions The machine grinds the There is no water. Fill the water tank and prime the coff ee beans but no coff ee circuit (chapter "Using the Machine comes out. for the First Time"). (See note) The brew group is dirty.
-
Page 66: Energy Saving
ENGLISH ENERGY SAVING Stand-by The Saeco full automatic espresso machine is designed for energy saving- proven by the Class A energy label. After 30 minutes of inactivity, the machine turns off automatically. If a product has been brewed, the machine performs a rinsing cycle. In stand-by mode, the energy consumption is below 1Wh. -
Page 67: Technical Specification
If you need service or support, please visit the Philips website at www.philips.com/support or contact the Philips Saeco hotline in your country. You fi nd its phone number in the warranty booklet by... -
Page 68: Ordering Maintenance Products
ORDERING MAINTENANCE PRODUCTS For cleaning and descaling, use Saeco maintenance products only. You can purchase these at the Philips online shop at www.shop.philips.com/ service, your local dealer or at authorised service centers. If you have any diffi culties obtaining maintenance products for your ma- chine, please contact the Philips Saeco hotline in your country. - Page 69 ENGLISH Milk Circuit Cleaner: CA6705 Maintenance Kit CA 6706...
- Page 72 The manufacturer reserves the right to make changes without prior notice. www.philips.com/saeco...