Devolo MT 02648 Manual
  1. Manuals
  2. Brands
  3. Devolo Manuals
  4. Security Sensors
  5. MT 02648
  6. Manual

Devolo MT 02648 Manual

Door/window contact and the motion detector
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Devolo home Control Door/Window
Contact MT 02648
The Door/Window Contact and the Motion Detector have two additional
functions integrated: temperature and illumination measurement, based
on Z-Wave
TM
technology.
It is the Z-Wave
TM
plus product, it support the security, OTA... Those
newest features of the Z-Wave
communication protocol designed for home automation, specifically to
remotely control applications in residential and light commercial
environments. The technology uses a low-power RF radio embedded or
retrofitted into home electronics devices and systems, such as lighting,
home access control, entertainment systems and household appliances.
The product can be included and operated in any Z-Wave
with other Z-Wave
TM
certified devices from other manufacturers and/or
other applications. All non-battery operated nodes within the network
TM
technology. Z-Wave
TM
is a wireless
will act as repeaters regardless of vendor to increase reliability of the
network.
The device adopt the Z-Wave
network system is all made by Z-Wave
network system will have the advantages as below.
Concurrent multi-channel support reduces external interference.
•
Better RF range, improve about 10 meters in indoor.
•
Support 100 Kbps transmit speed, speed up communication.
•
Function Compare A/B/C
Motion
Sensor
MT 02647
Door/Window
Contact
MT 02648
Add to/Remove from Z-Wave
There are two tamper keys in the device, one is in the back side,
another is in the front side. Both of them can add, remove, reset or
association from Z-Wave
In the first time, add the device into the Z-Wave
sure the primary controller is in the add mode. And then power on the
TM
network
device, just take out the insulation Mylar in the back side of the device.
The device will auto start the NWI (Network Wide Inclusion) mode. And
it should be included in 5 seconds. You will see the LED light ON one
1
TM
500 series chip, when your Z-Wave
TM
500 series devices. The
PIR
Temperature Illumination
Door/Window
V
V
TM
Network
TM
network.
TM
TM
V
V
V
V
network. First, make

Advertisement

Table of Contents
loading

Related Manuals for Devolo MT 02648

Summary of Contents for Devolo MT 02648

  • Page 1 Devolo home Control Door/Window will act as repeaters regardless of vendor to increase reliability of the network. Contact MT 02648 The device adopt the Z-Wave 500 series chip, when your Z-Wave network system is all made by Z-Wave 500 series devices. The network system will have the advantages as below.

  • Page 2: Function Description

    second. Note: The device support 2 groups. The group 1 is for receiving the report message, like triggered event, temperature, illumination etc. The group 2 is for light control, the device will send the “Basic Set” command Notice: Including a node ID allocated by Z-Wave Controller means to this group.
  • Page 3 In default the device will using Notification Report to represent the Notification Report (V4) trigger event, it can be changed to Sensor Binary Report by setting the Notification Type: Home Security (0x07) configuration NO. 7 Bit4 to 1. Event: Tampering. Product covering removed (0x03) * Motion Report: Sensor Binary Report (V2) When the Motion Detector detected, the device will unsolicited to send...

  • Page 4: Power Up Procedure

    *** Illumination differential report *** report except the low battery detection. This function default is disabled, to enable this function by setting the configuration NO.22 not to zero. Power Up Procedure Enable this functionality, the device will measure the illumination in every one minute.

  • Page 5: Operation Mode

    front tamper key once to start the update. NO. 5 to set the operation mode. After finish the firmware download, the LED will start flash in every 0.5 second. At that time, please don't remove the battery , otherwise it Operation Mode will cause the firmware broken, and the device will no function.

  • Page 7: Battery Installation

    Battery Installation When the device report the low battery message. The user should replace the battery to new one. The battery type is CR123A, 3.0V. The way to open the front cover please follow below steps. 1. Using a tool to press the 1-1 position, to release the cover. 2.

  • Page 8: Installation

    Installation Z-Wave Configuration Settings 1. In the first time, add the device into the Z-Wave network. First, Notice: make sure the primary controller is in the inclusion mode. And then * All of the configuration, the data size is 1. power on the device, just take out the insulation Mylar in the back side * The configuration mark with star(*), means after the exclusion the of the device.
  • Page 9 Name Description Name Description Def. A B C Def. A B C Valid Valid Setting the BASIC command value to Operation mode. Using bit to control. turn on the light. The 0xFF(-1) means    Bit0: Reserve. Basic Set turn on the light.
  • Page 10 Name Description Name Description Def. A B C Def. A B C Valid Valid Multisensor function switch. Using bit Customer function switch, using bit to control. control.    Bit0: Disable magnetic integrate Bit0: Reserve.    illumination. Bit1: Enable sending motion OFF Bit1: Disable PIR integrate report.
  • Page 11 Name Description Name Description Def. A B C Def. A B C Valid Valid In the normal mode, after the PIR The interval time for auto report the motion detected, setting the re-detect illumination. Auto Report time. 8 seconds per tick, default tick is 0 means turn off auto report ...

  • Page 12: Z-Wave Supported Command Class

    Name Description Def. A B C Valid Power by CR123A lithium battery. The illumination differential to report. Signal (Frequency): 0 means turn off this function. 868.40 MHz, 869.85 MHz(EU) The unit is percentage. Illumination Enable this function the device will ...

Table of Contents