Icom IC-F3023T Instruction Manual
  1. Manuals
  2. Brands
  3. Icom Manuals
  4. Transceiver
  5. IC-F3023T
  6. Instruction manual

Icom IC-F3023T Instruction Manual

Hide thumbs Also See for IC-F3023T:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
VHF TRANSCEIVERS
iF3021T/S
iF3023T/S
iF3026T/S
UHF TRANSCEIVERS
iF4021T/S
iF4023T/S
iF4026T/S
This device complies with Part 15 of the FCC Rules. Operation is
subject to the condition that this device does not cause harmful
interference.
American Communication Systems
Discover the Power of Communications
http://www.ameradio.com
TO ORDER – VISIT
™
The photo shows the 10-key
version VHF transceiver.

Advertisement

Table of Contents
loading

Related Manuals for Icom IC-F3023T

Summary of Contents for Icom IC-F3023T

  • Page 1 American Communication Systems Discover the Power of Communications ™ http://www.ameradio.com TO ORDER – VISIT INSTRUCTION MANUAL VHF TRANSCEIVERS iF3021T/S iF3023T/S iF3026T/S UHF TRANSCEIVERS iF4021T/S iF4023T/S iF4026T/S This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

  • Page 2: Explicit Definitions

    2 to 4 in. (5 instruction manual contains important operating instructions to 10 cm) away from the lips and the transceiver is vertical. for the IC-F3021T/S, IC-F3023T/S, IC-F3026T/S VHF TRANSCEIVERS and the IC-F4021T/S, IC-F4023T/S, IC- R CAUTION! NEVER operate the transceiver with a F4026T/S UHF TRANSCEIVERS.
  • Page 3 The use of non-Icom battery packs/chargers may impair transceiver performance and invalidate the warranty. For U.S.A. only CAUTION: Changes or modifications to this transceiver, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS IMPORTANT ................ i 6 OPTIONAL SWIVEL BELT CLIP ......22–23 I MB-93 contents ............22 EXPLICIT DEFINITIONS ............. i I Attaching ..............22 PRECAUTIONS ..............i I Detaching ..............23 TABLE OF CONTENTS ............iii 1 ACCESSORIES ............1–3 7 OPTIONS ...............

  • Page 5: Accessories

    ACCESSORIES I Supplied accessories I Accessory attachments D Flexible antenna NOTE: Some accessories are not supplied with depending on versions. Connect the supplied flexible anten- na to the antenna connector. Flexible antenna Battery pack Belt clip CAUTION! • NEVER HOLD the antenna when carrying the transceiver.
  • Page 6 ACCESSORIES D Belt clip ï Battery pack To attach the battery pack: To attach the belt clip: q Release the battery pack if it is attached. Slide the battery pack in the direction of the arrow (q), then w Slide the belt clip in the direction of the arrow until the belt lock it with the battery release button.
  • Page 7 ACCESSORIES ï Jack cover Attach the jack cover when the optional speaker-microphone or headset is not used. To detach the jack cover: To attach the jack cover: q Attach the jack cover to the [MIC/SP] jack. q Unscrew the screws using a phillips screwdriver. w Detach the jack cover for the speaker-microphone or w Tighten the screws.

  • Page 8: Panel Description

    PANEL DESCRIPTION I Front panel e DEALER-PROGRAMMABLE KEY [Side1] Desired function can be programmed by your dealer. (p. 7) r PTT SWITCH [PTT] Push and hold to transmit; release to receive. t DEALER-PROGRAMMABLE KEYS [Side2]/[Side3] Desired functions can be programmed independently by Speaker your dealer.
  • Page 9 PANEL DESCRIPTION o EXTERNAL MICROPHONE/SPEAKER JACK Connect an optional speaker-microphone or headset. NOTE: Connect or disconnect the optional equipment after the transceiver is turned OFF. Jack cover NOTE: Attach the jack cover when the optional equipment is not used. See (p. 3) for details. !0 VOLUME CONTROL [VOL] Rotate to turn the power ON/OFF and adjusts the audio level.

  • Page 10: I Function Display

    PANEL DESCRIPTION I Function display y SCRAMBLER INDICATOR Appears when the voice scrambler function is activated. u BELL INDICATOR Appears/blinks when the specific 2-tone code is received, according to the pre-programming. i KEY LOCK INDICATOR Appears during the key lock function is ON. o BATTERY INDICATOR q TRANSMIT INDICATOR Appears or blinks when the battery power decreases to a...

  • Page 11: I Programmable Function Keys

    [Side2], [Side3], [P0], [P1], [P2] and [P3] programmable function keys. ting. Consult your Icom dealer or system operator for details con- When the power ON scan function is turned OFF; cerning your transceivers programming. Push to start and cancel scanning operation. In case of If the programmable function names are bracketed in the fol- transmission during scan, scanning will be cancelled.
  • Page 12 PANEL DESCRIPTION PRIO A/B KEYS C.TONE CH ENT KEY ➥ Push to select Priority A or Priority B channel. Push to select the continuous tone channel using ➥ Push and hold [Prio A (Rewrite)] or [Prio B (Rewrite)] for 1 [CH Up]/[CH Down] to change the tone frequency/code set- sec.
  • Page 13 PANEL DESCRIPTION CALL KEYS TX CODE CHANNEL UP/DOWN KEYS Push to transmit a 2-tone. Push to select a TX code channel directly. • Call transmission is necessary before you call another station depending on your signaling system. SCRAMBLER FUNCTION • [Call A] and/or [Call B] may be available when your system employs Push to toggle the voice scrambler function ON and OFF.

  • Page 14: Basic Operation

    BASIC OPERATION I Turning power ON D Battery type selection Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. The battery type must be selected according to the attaching (p.

  • Page 15: I Channel Selection

    BASIC OPERATION I Channel selection I Call procedure Several types of channel selections are available. Methods When your system employs tone signaling (excluding CTCSS may differ according to your system set up. and DTCS), the call procedure may be necessary prior to voice transmission.

  • Page 16: I Receiving And Transmitting

    BASIC OPERATION I Receiving and transmitting D Transmitting notes NOTE: Transmitting without an antenna may damage the transceiver. See page 1 for accessory attachments. • Transmit inhibit function The transceiver has several inhibit functions which restrict Receiving: transmission under the following conditions: q Rotate [VOL] to turn the power ON.
  • Page 17 BASIC OPERATION D TX code channel selection D DTMF transmission If the transceiver has [TX Code CH Select] assigned to it, the If the transceiver has [DTMF Autodial] assigned to it, the auto- indication can be toggled between the operating channel matic DTMF transmission function is available.

  • Page 18: I User Set Mode

    BASIC OPERATION I User set mode I Emergency transmission User set mode is accessed at power ON and allows you to When [Emergency Single] or [Emergency Repeat] is pushed, set seldom-changed settings. In this case you can “cus- an emergency signal is automatically transmitted for the spec- tomize”...

  • Page 19: I Stun Function

    BASIC OPERATION I Stun function When the specified ID, set as a killer ID, is received, the stun function is activated. When the killer ID is received, the transceiver switches to the password required condition. Entering of the password via the keypad is necessary to operate the transceiver again in this case.

  • Page 20: Battery Charging

    Icom radios or Icom charger. Only Icom battery R DANGER! DO NOT expose the battery to rain, snow, sea- packs are tested and approved for use and charge with Icom water, or any other liquids. Do not charge or use a wet bat- radios or Icom charger.
  • Page 21 R DANGER! NEVER charge the battery pack in areas with abnormal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distrib- extremely high temperatures, such as near fires or stoves, utor.

  • Page 22: I Optional Battery Chargers

    BATTERY CHARGING I Optional battery chargers ï Rapid charging with the BC-160 ï AD-106 installation q Install the AD-106 desktop charger adapter into the holder The optional BC-160 provides rapid charging of optional Li- Ion battery packs. space of the BC-119N/BC-121N. w Connect the plugs of the BC-119N/BC-121N to the AD-106 •...
  • Page 23 BATTERY CHARGING ï Rapid charging with the BC-119N+AD-106 ï Rapid charging with the BC-121N+AD-106 The optional BC-119N provides rapid charging of battery The optional BC-121N allows up to 6 battery packs to be packs. The following items are additionally required. charged simultaneously.
  • Page 24 BATTERY CHARGING IMPORTANT!: Battery charging caution Ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter. (This illustration is described with the BC-160.) Lobs Guide rail...

  • Page 25: Battery Case

    BATTERY CASE I Optional battery case (BP-240) When using the optional battery case, install 6 × AAA (LR03) Fig.1 size alkaline batteries as illustrated at right. BP-240 q Unhook the battery cover release hook (q), and open the cover in the direction of the arrow (w). (Fig.1) w Then, install 6 ×...

  • Page 26: Optional Swivel Belt Clip

    OPTIONAL SWIVEL BELT CLIP I MB-93 contents e Clip the belt clip to a part of your belt. And insert the trans- ceiver into the belt clip until the base clip inserted fully into the groove. Qty. q Belt clip ……………………………………………………… 1 w Base clip ……………………………………………………...

  • Page 27: I Detaching

    OPTIONAL SWIVEL BELT CLIP I Detaching q Turn the transceiver upside down in the direction of the w Release the battery pack if it is attached. (p. 2) e Pinch the clip (q), and slide the base clip in the direction arrow and pull out from the belt clip.

  • Page 28: Options

    OPTIONS D BATTERY PACK D BELT CLIPS • MB-93 SWIVEL BELT CLIP Battery pack Voltage Capacity Battery life* • MB-94 BELT CLIP Exclusive alligator-type belt clip. The same as supplied with BP-230N 7.4 V 980 mAh 7.35 hrs. the transceiver. •...
  • Page 29 OPTIONS D OTHER OPTIONS • SP-13 EARPHONE Provides clear receive audio in noisy environment. • HM-158L/159L SPEAKER MICROPHONE Combination speaker-microphone that provides convenient operation while hanging the transceiver from your belt. • HS-94/HS-95/HS-97 + VS-1L HEADSET VOX / PTT CASE HS-94: Ear-hook type HS-95: Neck-arm type HS-97: Throat microphone...

  • Page 30: Safety Training Information

    • ALWAYS keep the antenna at least 2.5 cm (1 inch) away to Radio Frequency Electromagnetic Fields, 3 kHz to 300 from the body when transmitting and only use the Icom belt- GHz. clips listed on page 24 when attaching the radio to your belt, •...
  • Page 31 SAFETY TRAINING INFORMATION Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.
  • Page 32 A-6506D-1EX-w Printed in Japan 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan © 2006 Icom Inc.

This manual is also suitable for:

Ic-f3021tIc-f3026tIc-f4021tIc-f4023tIc-f4026tIc-f3021s ... Show all

Table of Contents