Summary of Contents for Oregon Scientific BAR122HG
Page 1
M EMOR Y C HA NN EL TIME Congratulations on your purchase of the Weather forecaster with cable free sensor and radio-controlled calendar clock (BAR122HG). M ODE /SET 24 hr This unit has a large four-line liquid crystal display (LCD) for...
Page 2
A . FRONT DISPLAY K. [ 24 hr OFF ] BUTTON A four line easy-to-read LCD Displays the alarm time, or changes the alarm set time A1. WEATHER FORECAST WINDOW L. [ON/OFF] BUTTON ( TEMP/% RH ALARM ) Graphically illustrates a weather forecast Enables / disables HI/LO temp alarm and HI/LO % RH alarm M.
TWO-LINE LCD FEATURES: REMOTE THERMO-HYGRO Displays the current temperature and humidity monitored by SENSOR the remote unit LED INDICATOR Flashes when the remote unit transmits a reading °C/°F SLIDE SWITCH Selects between Centigrade (°C) and Fahrenheit (°F) CHANNEL SLIDE SWITCH Designates the remote unit Channel 1, Channel 2 or Channel RESET Returns all settings to default values...
easier synchronization between the transmission and reception BATTERY AND CHANNEL INSTALLATION: of signals. REMOTE UNIT 4. Position the remote unit and main unit within effective transmission range, which, in usual circumstances, is up to 100 The remote thermo-hygro sensor unit uses two (2) UM-4 or “AAA” meters.
Remote unit LOW BATTERY WARNING Wall-mount Table Stand When it is time to replace batteries, the respective low-battery indicator will show up when the respective channel is selected. The battery level of the main unit will be shown on the indoor temperature when it is running low.
If no signals are received, blanks “---” will be displayed and the To display temperature / humidity readings from a remote kinetic wave icon will not show. sensor: • Press [CHANNEL] until the appropriate remote sensor channel To force a signal search: is displayed in the box under the kinetic-wave.
HOW TO READ THE KINETIC WAVE THE COMFORT-LEVEL ICONS DISPLAY The comfort level indicators COMFORT, WET or DRY will tell you if the curent environment is comfortable, too wet or too dry. The kinetic wave display shows the signal receiving status of the main unit.
TEMPERATURE, HUMIDITY & PRESSURE MAXIMUM AND MINIMUM TEMPERATURE TREND INDICATORS AND HUMIDITY The temperature-trend, humidity-trend and pressure trend indicators The maximum and minimum recorded temperature and humidity show the trends of collected readings. Arrows indicate a rising, readings will automatically be stored in the memory. steady or falling trend.
The high-low displays are as follows: The respective HI, LO or both indicators will light up to signify the status of the alarm. Sequence Respective Display If in another channel other than channel one is selected, when the Pressing HI/LO once Enters HI temperature display alarm activates the display will switch to channel-1 and the display will flash.
] button is pressed. CALENDAR CLOCK DISPLAY MODES ABOUT RADIO RECEPTION The BAR122HG supports four time display modes in the sequence The BAR122HG is designed to automatically synchronize its calendar clock once it is brought within range of the Frankfurt DCF77 radio signal.
] button for three HOW TO SET AND ARM THE ALARMS seconds. The BAR122HG has two alarms, ALARM 1 and ALARM 2. They The radio reception signal [ ] will start blinking to initiate reception can be invoked together or independently.
3. Enter the hour using [ TIME / ] and [ TIME / MAINTENANCE 4. Press . The minute digits will blink. When handled properly, this unit is engineered to give you years 5. Enter the minutes using [ TIME / ] and [ TIME / of satisfactory service.
Temperature resolution : 0.1°C (0.2°F) NOTE ON COMPLIANCE Relative Humidity Operating : 25% RH to 90% RH range Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the Remote thermo-hygro unit user’s authority to operate the equipment.
Page 14
COUNTRIES RTTE APPROVAL COMPLIED: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Italy, Luxembourg, Netherlands, Portugal, Spain, Sweden, UK and Ireland.