Panasonic KX-TCD816UAS Service Manual page 66

KX-TCD816UAS / KX-TCD816UAT / KX-TCA181UAS / KX-TCA181UAT
23.3.3. Flash Time Setting
Address Initial
Type
0365 1 EEP_FlashTime1
0366 1 EEP_FlashTime2
0367 1 EEP_FlashTime3
23.3.4. Clip (Caller ID) configuration
Address Initial
Type
0228 1
0229 1
022A 1
03B1 1
03B2 1
03B3 1
03B4 1
03B5 1
03B6 1
Name
Calibrated loop-break time for "80 ms"
Unit: 10 ms, defaults to 80 ms
Calibrated loop-break time for "90 ms"
Unit: 10 ms, defaults to 90 ms
Calibrated loop-break time for "100 ms"
Unit: 10 ms, defaults to 100 ms
Name
EEP_ClipDetectConfig
EEP_FskInterdigitTimeout
EEP_RuClipReqLev
EEP_ClipRingConfig
EEP_ImpSetConfig
EEP_ImpRemConfig
EEP_CasAckDtmf
EEP_DtmfReceiveDataCount
EEP_ClipPhaseConfig
Description
Description
CLIP detect configuration
Bit0-2:Mode...1:DTMF only, 2:FSK only,
3:FSK/DTMF both, 4:Russian CLIP
Bit3:Onhook...1=enable, 0=disable
Bit4:Offhook...1=enable, 0=disable
Bit5:MsgWaiting...1=enable, 0=disable
Bit6:KpnVmwi...1=enable, 0=disable
Bit7:Unused
FSK Interdigit timeout
Unit: 10ms, Defalut: 80ms
RCID REQ signal Level
Default: -4.3dBm
Ring configuration
Bit0:Rpas...1=enable, 0=disable
Bit1:RpasAlert...1=enable, 0=disable
Bit2:Rpas2LongAlert...1=enable, 0=disable
Bit3:Suppress1stRing...1=enable, 0=disable
Bit4:Check1stRing...1=enable, 0=disable
Bit5:RingEarlier...1=enable, 0=disable
Bit6-7:Unused
Impedance Set configuration
Bit0:Polarity...1=enable, 0=disable
Bit1:Dtas...1=enable, 0=disable
Bit2:Rpas...1=enable, 0=disable
Bit3:PowerRing...1=enable, 0=disable
Bit4:LearnImpPattern...1=enable, 0=disable
Bit5:CheckPolStatus...1=enable, 0=disable
Bit6-7: Unused
Impedance Remove configuration
Bit0:Polarity...1=enable, 0=disable
Bit1:Ringing...1=enable, 0=disable
Bit2:ClipReceived...1=enable, 0=disable
Bit3:Offhook...1=enable, 0=disable
Bit4:ChszDet...1=enable, 0=disable
Bit5-7:Unused
CAS Acknowledge DTMF tone
00:DTMF 0 - 09:DTMF 9
0A:DTMF A
0B:DTMF B
0C:DTMF C
0D:DTMF D
0E:DTMF
0F:DTMF #
Valid Receive data Count (for INDIA)
CLIP phase set configuration
Bit0:ForwardNumber...1=enable, 0=disable
Bit1:CallingNumber...1=enable, 0=disable
Bit2:Dutch...1=enable, 0=disable
Bit3:Chinese...1=enable, 0=disable
Bit4:PriorityCheck...1=enable, 0=disable (for
France)
Bit5-6:AddZero...0:no add zero, 1:add zero
absolutely 2:Check Number's top is zero. If it
is zero, add zero.
Bit7:TwDtmf...1=enable, 0=disable
Bit8:FskRemoveParity...1=enable, 0=disable
Bit9:AutoRappel...1=enable, 0=disable
Bit10:KpnStartEndNg
Bit11:CheckCidSendFlg
Bit12:If DTMF CLIP come in series,
0:First data is available,
1:Last data is available
Bit13-15:Unused
66
Default value Country
Setting
0x08 x
0x09 x
0x0A x
Default Country
value Setting
0x3B 0x3C
0x08 x
0x00, 0x60,
0x13 0x15
0x20 x
0x15 x
0x0F x
0x0D x
0x04 x
0x01, x
0x04