Advertisement
E2TC2BD_EN.book Page 39 Thursday, May 7, 2009 9:02 AM
6
Press [C STOP] on the unit to stop recording.
Note
• During recording, recording will be paused when a signal
other than PAL or SECAM is detected. (See "Video Colour
System" on page 38 for details.)
• The signal from the external device will be output
automatically when the TV is connected to AV1 and the
external device is connected to AV2 using a Scart cable with
its power on (The signal from this unit cannot be monitored
except during playback.).
If you want to monitor this unit's signal, press [DISPLAY]
or turn the external device off.
If you want to monitor the signal from other input, press
[DISPLAY], then press [INPUT SELECT F] to select the
desired external input mode, then select the desired input
channel using [PROG. G \ H].
Information on DV Dubbing
This function helps you to dub the contents in the DVC (digital
video camcorder) to HDD or DVD easily.
You can control basic operations of the DVC from the remote
control of this unit if the DVC is in video mode.
Guide to DV and On-Screen Display
1
Connect your DVC to the DV input jack on the
front panel using a DV cable. (Use the DV cable
that has 4-pin input jack and is compliance with
the IEEE 1394 standards.)
2
Press [INPUT SELECT F] repeatedly to select
the external input channel, then press
[PROG. G \ H] repeatedly to select DV(AV4).
3
Press [DISPLAY] to display the DVC information
on the screen.
When the DVC is in video mode...
T
1/ 1
C
1/ 1
1
2
Control
DVD
DV Audio
Stereo1
Start Rec
3
4
When the DVC is in camera mode...
T
1/ 1
C
1/ 1
7
The menu changes according to the mode of DVC.
Switch the mode on the DVC to video mode for the dubbing
information.
-RW
VR
ORG
DV
AB-1234
0:12:34
DVD SP
2:00
-RW
VR
ORG
5
DV
AB-1234
0:12:34
DVD SP
2:00
6
The following instructions are described with the
operations using the remote control of this unit.
1 DV icon
2 Indicator of active device
• With "Control" highlighted, press [ENTER\OK] to display
the available devices to control with the remote control
of this unit. Select the device you want to operate using
[K \ L], then press [ENTER\OK].
- Select "HDD" / "DVD" to control this unit with the remote
control of this unit.
- Select "DVC" to control your DVC with the remote
control of this unit.
3 Recording audio mode
• "DV Audio" can be changed. With "DV Audio" selected,
press [ENTER\OK] to display "DV Audio" menu. Select
the audio you want to output using [K \ L], then press
[ENTER\OK].
- Select "Stereo1" to dub the stereo sound.
- Select "Stereo2" to dub the sound that was added after
the recording.
- Select "Mix" to dub the stereo1 and stereo2.
4 Command menu
• "Start Rec" or "Pause Rec" will appear.
5 External input channel
6 Product name of your DVC
• If the unit cannot recognise the input signal from the
DVC or if it is the unknown product, "No Device" or "****"
will appear instead.
7 Status of the current operation and the time
counter
Each icon means (Available icons may vary depending on
the DVC):
DVC is in stop mode.
DVC is in playback mode.
DVC is in pause mode.
DVC is fast forwarding. (standard speed)
DVC is fast forwarding. (faster than above)
DVC is fast forwarding. (faster than above)
DVC is slow forwarding. (standard speed)
DVC is slow forwarding. (faster than above)
DVC is slow forwarding. (faster than above)
DVC is fast forwarding. (in stop mode)
DVC is fast reversing. (in stop mode)
DVC is fast reversing. (standard speed)
DVC is fast reversing. (faster than above)
DVC is fast reversing. (faster than above)
DVC is in slow reverse playback.
DVC is in recording.
DVC is in recording pause mode.
Please also read the operating instructions of your
DVC for more information.
39
EN
Advertisement
