Table of Contents
Advertisement
5
System Set Up
5.1.8 Using SD memory card
The heat pump unit is equipped with an SD memory card inter-
face in FTC.
Using an SD memory card can simplify main remote controller
settings and can store operating logs. *1
<Handling precautions>
(1) Use an SD memory card that complies with the SD stand-
ards. Check that the SD memory card has a logo on it of
those shown to the right.
(2) SD memory cards to the SD standards include SD, SDHC,
miniSD, micro SD, and microSDHC memory cards. The
capacities are available up to 32 GB. Choose that with a
maximum allowable temperature of 55ºC.
(3) When the SD memory card is a miniSD, miniSDHC, mi-
croSD, or micro SDHC memory card, use an SD memory
en
card converter adapter.
(4) Before writing to the SD memory card, release the write-
protect switch.
(5) Before inserting or ejecting an SD memory card, make sure
to power off the system. If an SD memory card is inserted
or ejected with the system powered on, the stored data
could be corrupted or the SD memory card be damaged.
*An SD memory card is live for a short duration after the
system is powered off. Before insertion or ejection wait until
the LED lamps on the FTC control board are all off.
(6) The read and write operations have been verifi ed using the
following SD memory cards, however, these operations are
not always guaranteed as the specifi cations of these SD
memory cards could change.
Manufacturer Model
Verbatim
#44015
SanDisk
SDSDB-002G-B35
Panasonic
RP-SDP04GE1K
Arvato
2GB PS8032 TSB 24nm MLC
Arvato
2GB PS8035 TSB A19nm MLC Jul. 2014
SanDisk
SDSDUN-008G-G46
Verbatim
#43961
Verbatim
#44018
VANTASTEK VSDHC08
RiTEK
RiDATA 8GB SDHC
Before using a new SD memory card (including the card that
comes with the unit), always check that the SD memory card
can be safely read and written to by the FTC controller.
<How to check read and write operations>
a) Check for correct wiring of power supply to the system.
For more details, refer to section 4.6.
(Do not power on the system at this point.)
b) Insert an SD memory card.
c) Power on the system.
d) The LED4 lamp lights if the read and write operations
are successfully completed. If the LED4 lamp continues
blinking or does not light, the SD memory card cannot
be read or written to by the FTC controller.
(7) Make sure to follow the instruction and the requirement of
the SD memory card's manufacturer.
(8) Format the SD memory card if determined unreadable in
step (6). This could make it readable.
Download an SD card formatter from the following site.
SD Association homepage: https://www.sdcard.org/home/
35
(9) FTC supports FAT fi le system but not NTFS fi le system.
(10) Mitsubishi Electric is not liable for any damages, in whole
or in part, including failure of writing to an SD memory
card, and corruption and loss of the saved data, or the
like. Back up saved data as necessary.
(11) Do not touch any electronic parts on the FTC control board
when inserting or ejecting an SD memory card, or else the
control board could fail.
(a) For insertion, push on the SD memory card until it clicks
into place.
(b) For ejection, push on the SD memory card until it clicks.
Note: To avoid cutting fi ngers, do not touch sharp edges
of the SD memory card connector (CN108) on the
FTC control board.
Logos
Tested in
Mar. 2012
Oct. 2011
Oct. 2011
Jun. 2012
Oct. 2016
Oct. 2016
Capacities
Oct. 2016
2 GB to 32 GB *2
Sep. 2017
SD speed classes
Aug. 2021
All
• The SD Logo is a trademark of SD-3C, LLC.
The miniSD logo is a trademark of SD-3C, LLC.
The microSD logo is a trademark of SD-3C, LLC.
*1 To edit main remote controller settings or to check operating
data, an ecodan service tool (for use with PC) is required.
*2 A 2-GB SD memory card stores up to 30 days of operation
logs.
(a)
(b)
Advertisement
Table of Contents
