Advertisement
Quick Links
Advertisement
Related Manuals for Draytek Vigor1000B
Summary of Contents for Draytek Vigor1000B
- Page 2 Vigor1000B Multi-WAN Security Router Quick Start Guide Version:1.0 Firmware Version: V3.9.6.3 (For future update, please visit DrayTek web site) Date: August 23, 2021...
- Page 3 Intellectual Property Rights (IPR) Information © All rights reserved. This publication contains information that is protected Copyrights by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. The following trademarks are used in this document: Trademarks ...
- Page 4 EU Declaration of Conformity We DrayTek Corp. , office at No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan, declare under our sole responsibility that the product Product name: Multi-WAN Security Appliance Model number: Vigor1000B Manufacturer: DrayTek Corp.
-
Page 5: Table Of Contents
1. Package Content ....................1 2. Panel Explanation....................2 2.1 LED ............................2 2.2 Connectors ..........................3 3. Hardware Installation ................... 4 3.1 Connecting Device ........................4 3.2 Rack-Mounted Installation......................5 4. Software Configuration ..................6... -
Page 6: Package Content
Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Vigor router Quick Start Guide RJ-45 Cable (Ethernet) Rack mount kit (brackets) Console Connector Console Flat Cable The type of the power cord depends on the country that the router will be installed. -
Page 7: Panel Explanation
Status Explanation The router is powered on. The router is powered off. Blinking The system is active. The system is hanged. The USB device is installed and ready. No USB device is installed. The fiber connection is established. Blinking The data is transmitting. SFP+ No fiber connection is established or the system is hanged. -
Page 8: Connectors
Interface Description USB1 / USB2 Connecter for the USB device. Console Provided for technician use. SFP+ (P1~P2) Connecter for SFP module with the rate of 10G/1G bps. Connectors for remote network devices or local P3~P6 network devices (WAN/LAN) with the rate of 1G/100M/10M bps. -
Page 9: Hardware Installation
Before starting to configure the router, you have to connect your devices correctly. Connect a modem to any WAN port of Vigor1000B with Ethernet cable (RJ-45) to access Internet. Connect the other end of the cable (RJ-45) to the Ethernet port on your computer (that device also can connect to other computers to form a small area network). -
Page 10: Rack-Mounted Installation
The Vigor1000B can be mounted on the shelf by using standard brackets shown below. Fasten the rack mount kit on both sides of the Vigor router using specific screws. Then, install the Vigor router (with rack mount kit) on the 19-inch chassis by... -
Page 11: Software Configuration
To access Internet, please finish basic configuration after completing the hardware installation. 1. Make sure your PC connects to the router correctly. Note You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router 192.168.1.1. - Page 12 3. Now, the Main Screen will pop up. 4. Open WAN>>Internet Access. WAN1 is dedicated for SFP connection; WAN3 ~WAN6 are designed for Ethernet connection. When your ISP provides fiber connection, click Details Page of WAN1. If not, click Details Page of WAN3 ~ WAN6 according to the physical connection.
- Page 13 Click Details Page of WAN3. When the following page appears, choose PPPoE. After clicking Enable and entering the Username/Password provided by your ISP, click OK to get the following page. To reboot the system, click OK again.
- Page 14 Later, Vigor system will reboot. Please login Vigor router again. Then, you can enjoy surfing on the Internet.
- Page 15 Click Details Page of WAN3. When the following page appears, choose Static or Dynamic IP. After clicking Enable and configuring the settings according to the data provided by your ISP, click OK to get the following page. To reboot the system, click OK again.
- Page 16 Later, Vigor system will reboot. Please login Vigor router again. Then, you can enjoy surfing on the Internet.
- Page 17 Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents.