Related Manuals for Tascam LR-10
Summary of Contents for Tascam LR-10
- Page 1 D01128520B LR-10 Instrumental Trainer/Recorder This device has a serial number located on the bottom panel. Please record it and retain it for your records. Serial number: __________________ OWNER’S MANUAL...
-
Page 2: Important Safety Instructions
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. TASCAM LR-10 WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. FOR U.S.A. - Page 3 Replace only with the same or equivalent type. • Caution should be taken when using earphones or headphones with the product because excessive sound pressure (volume) from earphones or headphones can cause hearing loss. TASCAM LR-10...
- Page 4 • The unit power should be off when you install and replace batteries. TASCAM LR-10 • Remove the batteries if you do not plan to use the unit for a long time. Batteries could rupture or leak, causing fire, injury or stains around them.
- Page 5 (e) The return and collection systems are available to the end users. For more detailed information about disposal of waste batteries and/or accumulators, please contact your city office, waste disposal service or the shop where you purchased them. Pb, Hg, Cd TASCAM LR-10...
-
Page 6: Table Of Contents
Precautions for use ... 22 Precautions for placement and use ... 23 Beware of condensation ... 23 Cleaning the unit ... 23 TASCAM LR-10 2–Names and Functions of Parts ...24 Top panel ... 24 Left side panel ... 30 Right side panel ... 30 Rear panel ... - Page 7 Using the PLAY MODE screen to set the playback area ... 64 Selecting a folder for the playback area (1) ... 65 Selecting a folder for the playback area (2) ... 66 Playlist ... 67 Adding files to the playlist ... 67 Editing the playlist ... 67 TASCAM LR-10...
- Page 8 13–Using the tuner ...80 Preparation ... 80 Chromatic tuner mode (AUTO) ... 81 Oscillator mode ... 81 14–Using the Metronome ...82 TASCAM LR-10 Setting the metronome ... 82 Starting and stopping the metronome ... 82 15–System settings ...83 System settings (SETUP) ... 83 Setting the forward/backward search speed ...
- Page 9 Analog audio input ... 97 Output ratings ... 97 Analog output ratings ... 97 Control input/output ratings ... 97 Audio performance ... 98 Computer compatibility ... 98 Other specifications ... 98 Dimensional drawings ... 99 Table of Contents TASCAM LR-10...
-
Page 10: Quick Start Guide
Formatting is necessary if you insert a new SD card. (Formatting will erase all the data on the card.) For details, see “Inserting and removing SD cards” on page 39. TASCAM LR-10 Preparing the power ª Using AA batteries Insert AA batteries into the battery compartment, which you opened when installing the SD card. - Page 11 USB bus power or to connect the unit’s storage to the computer. Select BUS POWER Quick Start Guide Using an AC adaptor (sold separately) Connect a TASCAM PS-P520 AC adaptor (sold separately), which is designed for the specifications of this unit, to the DC IN 5V jack. TACAM PS-P520...
-
Page 12: Step 2: Copy Audio Files From A Computer
Use the included USB cable to connect the unit to the computer. Transfer files from the computer ª Copy audio files to the MUSIC folder on the LR-10 drive that appears on the computer. Disconnect from the computer ª After using the correct procedures to dismount the LR-10 drive from your computer, disconnect the USB cable. -
Page 13: Step 4: Connect An Instrument And Headphones
LINE IN jack or built-in microphones. Press the TUNER button to open the ). If mic input is menu ), press the ¶/MIC For details, see Chapter 13 “Using the tuner” on page 80. Quick Start Guide screen. TUNER TASCAM LR-10... -
Page 14: Step 6: Use The Effects
Press and hold the EFFECT button to open the where you can make detailed settings. For details, see Chapter 12 “Using the built in effects” on page TASCAM LR-10 Step 7: Adjust the input and output levels Adjust the headphones volume ª... -
Page 15: Step 8: Play Along With The Music
IN point. Then, press the LOOP button briefly again at the point where you want to stop loop playback to set the OUT point and start loop playback of the interval between the points. Quick Start Guide TASCAM LR-10... - Page 16 1 REPEAT ALL REPEAT After making the setting, press the HOME button to return to the Home Screen. TASCAM LR-10 For details about repeat playback, see “Repeat and single track playback” on page 75. Change the key ª...
-
Page 17: Step 9: Record Your Performance
For details, see “Recording the input sound with the playback sound (overdubbing)” on page 51. CAUTION If you press and hold the record button, the unit will be put in recording standby with the pre-record function enabled, and overdubbing will not be possible. [ª] Quick Start Guide TASCAM LR-10... -
Page 18: Step 11: Use Other Functions
For details, see chapter 14 “Using the Metronome” on page 82. Step 12: Turn off the power To turn the power off (put the unit in standby), press the [ª] button and hold it until the shutdown screen appears. TASCAM LR-10... -
Page 19: 1-Introduction
Thank you very much for purchasing the TASCAM LR-10 Instrumental Trainer/Recorder. Please read this Owner’s Manual carefully in order to maximize your use of all the unit’s features. We hope that you will enjoy using this trainer/ recorder for many years to come. Please keep a copy of this manual in a safe place for future reference. -
Page 20: Included Items
Mini-B type USB 2.0 port • Can be powered by two AA batteries, USB bus power or a • TASCAM PS-P520 AC adaptor (sold separately) Files saved on a computer can be transferred (copied) to • the SD card in this unit via USB Included items The included items are listed below. -
Page 21: Intellectual Property Rights
Instructions that should be followed to avoid injury, damage to the unit or other equipment, and loss of data. Intellectual property rights TASCAM is a trademark of TEAC Corporation, registered in • the U.S. and other countries. SDHC Logo is a trademark of SD-3C, LLC. -
Page 22: About Sd Cards
A list of SD cards that have been tested with this unit can be found on the TASCAM web site (www.tascam.com/). Use of cards that have not been verified for use with this unit could result in the unit not functioning properly. -
Page 23: Precautions For Placement And Use
Use a dry soft cloth to wipe the unit clean. Do not clean the unit with a chemically treated cloth or substances such as benzene, thinner and alcohol because they might cause damage to the surface of the unit. TASCAM LR-10... -
Page 24: 2-Names And Functions Of Parts
This shows a variety of information. 2 PEAK indicator This lights if the input signal level is too high. TASCAM LR-10 3 Cursor control Press up to use the §/BROWSE button, down to use the ¶/MIC button, left to use the  button and right to use the ¯... - Page 25 Use to return from the FILE INFORMATION message when using the browse function. Press and hold to turn the power ON or put the unit into standby. pop-up TASCAM LR-10...
- Page 26 Press and hold when stopped to enable prerecording (2 seconds maximum) and start recording standby. When in recording standby, the indicator blinks. Press during TASCAM LR-10 recording standby to start recording. When recording, the indicator lights. Press the Á button while pressing and holding this button to start overdubbing.
- Page 27 Adjust the pitch in semitones using the Adjust the pitch in cents using the For details, see “Changing the key” on page 70. t TUNER button Press to tune the instrument. mode. mode. FINE TUNE TASCAM LR-10...
- Page 28 MENU button When the Home Screen is open, press this button to open screen. MENU TASCAM LR-10 using the The cursor starts on the last used item. Press this button when one of the setting screens is open to return to the Press this button when the to the Home Screen.
- Page 29 ¯ button to designate the OUT point. You can press the Â/¯ button again to change the IN/OUT point. Use the Á and Ô/ buttons to find the location in the track where you want to set each point. – LOOP 1 LOOP 5 TASCAM LR-10...
-
Page 30: Left Side Panel
Use this port to connect the unit to a computer using the included USB cable. (See “Connecting with a computer” on page 46.) s REMOTE jack Connect a TASCAM RC-3F foot switch (sold separately), which is designed for use with this unit, to this 2.5-mm TRS jack. TASCAM LR-10... -
Page 31: Rear Panel
Rear panel h DC IN 5V jack Connect a TASCAM PS-P520 AC adaptor (sold separately), which is designed for the power requirements of this unit. 2–Names and Functions of Parts Front panel j Built-in stereo microphone (L/R) This is an electret condenser stereo microphone. To use this microphone as the input source, set screen. -
Page 32: Bottom Panel
2–Names and Functions of Parts Bottom panel l Battery compartment cover ; Battery compartment TASCAM LR-10 Install batteries (2 AA) in this compartment to power the unit. (See “Using AA batteries” on page 42.) z SD card slot Use to insert and remove SD cards. (See “Inserting and... -
Page 33: Home Screen
: Line input ON 6 Power supply status When the unit is being operated on battery power, a battery ( ) icon is shown. The amount of remaining battery charge is shown by the number of bars in the icon ( TASCAM LR-10... - Page 34 ( ) icon blinks. When this happens, the unit will soon switch to standby. When using a TASCAM PS-P520 AC adaptor (sold separately) or USB bus power, the AC ( NOTE Even when some battery charge is remaining, a “...
-
Page 35: Recording Screen
2 Prerecord or auto record function status When prerecording is enabled and the unit is in recording standby, “PRE”( When the auto record function is enabled and the unit is recording, “A.REC” ( Normal playback speed 110–150% speed 50–90% speed appears here. appears here. TASCAM LR-10... -
Page 36: Menu Structure
(hours: minutes: seconds). 8 Remaining recording time This shows the remaining amount of recording time available (hours: minutes: seconds) on the current SD card TASCAM LR-10 9 Level meter When MIC or LINE is ON ( volume level of the input signals. -
Page 37: Using The Menu
4. Use the VALUE (+/–) buttons to change the setting. 5. Repeat steps 3 and 4 as necessary for the other items. 6. Press the MENU button to return to the Press the HOME button to return to the Home Screen. ” becomes screen. MENU TASCAM LR-10... -
Page 38: Basic Operations
Use this button to move the cursor (change the highlighted item) left on a setting screen and to close the open folder on the screen. BROWSE TASCAM LR-10 VALUE (+/-) buttons Use to change value of the selected item. RECORD [º] button On the MENU Á... -
Page 39: 3-Preparation
2. Insert the SD card into the SD card slot in the back of the battery compartment in the direction shown in the illustration until it clicks into the place. 3. Insert the card and close the cover. If you are using batteries, insert them first before closing the cover TASCAM LR-10... -
Page 40: Removing An Sd Card
• this unit. A list of SD cards that have been verified to work with this • unit is posted on the TASCAM website (http://www.tascam. com/). TASCAM LR-10 Preparing an SD card for use To use an SD card with this unit, you must format it by using this unit first. -
Page 41: Special Cases
FORMAT ERROR appear. In this case, format the card to use it with this unit. SD cards that have been formatted by a TASCAM DR series device, however, are compatible with this model. If the system file or another important file has been •... -
Page 42: Powering The Unit
3–Preparation Powering the unit This unit can be powered by two AA batteries, USB bus power or a TASCAM PS-P520 AC adaptor (sold separately). This unit can use either alkaline or nickel-metal hydride (NiMH) batteries. Using AA batteries As described in the “Inserting and removing SD cards” section above, this unit has a battery compartment in the bottom. -
Page 43: Using An Ac Adaptor (Sold Separately)
PS-P520 (sold separately) CAUTION Never use any adaptor other than the TASCAM PS-P520 AC adaptor (sold separately), because it is designed for the power requirements of this unit. Use of a different adaptor could cause malfunction, fire or electric shock. -
Page 44: Startup And Shutdown
Turning the power on When the unit is in standby mode, press and hold the button until the startup screen opens. TASCAM LR-10 The Home Screen opens after the unit completes startup. TASCAM LR-10 Startup Screen Setting the power to standby... -
Page 45: Setting The Date And Time
The date and time setting can only be maintained for a few minutes when the unit is not powered by batteries, USB bus power or an AC adaptor. When using batteries, we recommend that you replace or recharge them before they completely lose power. Screen. MENU 3–Preparation TASCAM LR-10... -
Page 46: 4-Connecting
Failure to do so could cause the sudden output of loud sounds, which might lead to hearing damage or other harm. TASCAM LR-10 Connecting with a computer By connecting this unit with a computer, you can transfer... -
Page 47: Disconnecting From A Computer
LR-10. The LR-10 drive contains MUSIC and UTILITY folders. Disconnecting from a computer After using the correct procedures to dismount the LR-10 drive from your computer, disconnect the USB cable. The unit should automatically turn off. Please refer to the operation manual for your computer system for instructions about the correct procedures for dismounting an external drive. -
Page 48: 5-Recording
INPUT SETTING open the screen. INPUT SETTING TASCAM LR-10 This screen has the following setting items. Use the §/BROWSE and ¶/MIC buttons to select the desired item. (When selected, the “ and the setting value appears as light letters on a dark background.) Use the VALUE (+/–) buttons to change the... -
Page 49: Adjusting The Input Level
MONO tions where unexpected loud sounds might occur, set this function to recording without distortion. Use the LR-10’s built-in effects as necessary on the input • source signal. (See “Using the built-in effects” on page 78.) , but as the cut-off... -
Page 50: Recording
Before following these procedures, adjust the input level and open the Home Screen. 1. Press the RECORD [º] button briefly to start ordinary recording. TASCAM LR-10 When recording starts, the RECORD [º] button indicator lights and the display shows the elapsed and remaining recording times. -
Page 51: Recording A Few Seconds Before Pushing The Record Button (Pre-Recording)
For example, you could record a new instrument part over an existing track. NOTE When overdubbing, You cannot use the auto-record or • manual file incrementation functions. You cannot pause during overdubbing. (The • button does not respond if pushed.) 5–Recording RECORD [º] TASCAM LR-10... -
Page 52: Overdubbing
), changing the value has no effect on the BALANCE volume. TASCAM LR-10 4. Press the Á button while pressing and holding the RECORD [º] button to begin overdubbing. CAUTION If you press and hold the RECORD [º] button long , the unit will be put in recording standby with the pre-record function enabled, and overdubbing will not be possible. -
Page 53: Starting And Pausing Recording Automatically (Auto Rec)
RECORD [º] button indicator blinks. Press and hold the RECORD [º] button to enable the pre-record function and put the unit into recording standby. 5–Recording BROWSE or ¶ MIC button to select the item. (default value), -6dB -12dB TASCAM LR-10 -24dB... -
Page 54: Track Incrementation
CAUTION When overdubbing, the auto-recording function cannot be used. TASCAM LR-10 Track incrementation START LEVEL You can start recording to a new file without interruption manually. If a file reaches the maximum size (2GB), the unit will also automatically start recording to a new file. -
Page 55: Automatic Track Incrementation By File Size
5. Press the Á button to divide the file. Press the DIVIDE screen to BROWSE screen. MENU 5–Recording BROWSE and ¶/ MIC buttons to select the menu item, and press the Á button or ¯ screen. DIVIDE [ª] button to cancel division and return to screen. TASCAM LR-10... -
Page 56: Recording Duration
Division is not possible if a file that already exists has the • same name as the name that would be given to a new file created by division. TASCAM LR-10 Recording duration The table below shows the approximate amount of recording time possible on SD/SDHC cards of different capacities. -
Page 57: 6-Working With Files And Folders (Browse Screen)
BROWSE following meanings. MUSIC folder ( The MUSIC Folder is the highest (root) level folder in the hierarchy shown on the Screen. BROWSE ¯ button to show  key to exit Á key to open Screen have the TASCAM LR-10... -
Page 58: File Operations
Use the § item, and press the Á button to execute one of the following operations. TASCAM LR-10 PLAY Play the file and reopen the Home Screen. If the playback area is set to “FOLDER”, the playback area becomes the folder that contains that file. -
Page 59: Folder Operations
Press the Á button to create a new folder, or press the [ª] button to cancel the operation. However, if you try to create a new folder inside a second level subfolder the and the folder is not made. message appears Layer too Deep TASCAM LR-10... -
Page 60: Delete The Selected Playback File (Quick Delete)
You cannot erase read-only files or files that are not recognized by this unit. CANCEL No operation is conducted and the selected folder is left as is. TASCAM LR-10 Delete the selected playback file (QUICK DELETE) Use the following procedure to conveniently delete the currently selected playback file. -
Page 61: 7-Playback
NOTE SD cards that have been formatted by a TASCAM DR series device can also be used with this unit. Playback When the unit is stopped, press the Á button to start playback. -
Page 62: Searching Forward And Backward
Searching will not continue into the previous or next file even if you continue to hold the button. TASCAM LR-10 Adjusting the playback volume Use the OUTPUT (+/–) buttons to adjust the volume level output from the built-in speaker or the /LINE OUT jack. -
Page 63: Adjusting The Balance Between Playback And Input Signals
”. When the MIC/LINE input is off ( setting is canceled and the playback level returns to its original setting. 7–Playback icon appears as light letters on a dark ) when input is enabled. ), the BALANCE TASCAM LR-10 appears... -
Page 64: 8-Playback Area And Playlist
BROWSE and ¶/MIC button to select and press the Á button or ¯ button to open MODE screen. PLAY MODE TASCAM LR-10 3. Select the light letters on a dark background. BROWSE 4. Use the VALUE (+/–) buttons to select one of the following playback areas. -
Page 65: Selecting A Folder For The Playback Area (1)
“BROWSE screen navigation” on page 57. 3. Press the Á button to open the pop-up menu shown below. 8–Playback Area and Playlist Screen, the playback area changes to the BROWSE button to BROWSE and ¶/MIC buttons to select the screen, see BROWSE TASCAM LR-10... -
Page 66: Selecting A Folder For The Playback Area (2)
BROWSE 2. Use the § BROWSE and ¶/MIC buttons to select the desired folder (light on dark). TASCAM LR-10 3. Press the ¯ button to show the contents of that folder. 4. Use the § desired file (light on dark). -
Page 67: Playlist
2. Use the § PLAYLIST PLAYLIST 8–Playback Area and Playlist , and press the Á button to add that ADD LIST MENU BROWSE and ¶/MIC buttons to select the menu item, and press the Á button to open screen. PLAYLIST screen. TASCAM LR-10... - Page 68 Press the Á button to remove all the files or the operation. TASCAM LR-10 For this operation, it does not matter which track you select in step 3. All the files are removed from the playlist, but they are not erased from the SD card.
- Page 69 2. Press the Á button to complete the movement and return to the ordinary PLAYLIST number no longer appears light on dark.) CANCEL No operation is conducted on the selected file, and the pop-up menu closes. screen. (The file 8–Playback Area and Playlist TASCAM LR-10...
-
Page 70: 9-Special Playback (Playback Control Function)
SPEED shown, and when it is set from x1.1–x1.5, the shown. TASCAM LR-10 Changing the key You can use the KEY function to change the pitch of playback in semitone intervals (and the FINE TUNE function to change it in cents) without changing the speed. -
Page 71: Jump Back A Set Amount And Continue Playback (Flashback)
(Default value: 6. After completing the setting, press the HOME button to return to the Home Screen. FLASH screen. MENU BROWSE and ¶/MIC buttons to select the menu item. BROWSE and ¶/MIC buttons to select seconds) TASCAM LR-10 item. PLAY... -
Page 72: 10-Loop Playback/Repeat Playback/Single Track Playback
The current position is set as the IN (starting) point. 2. Press the LOOP button at the point when you want loop playback to stop. TASCAM LR-10 The current position is set as the OUT (ending) point, and loop playback between the IN (starting) and OUT (ending) points begins. -
Page 73: Using Loop Playback With The Playlist
Loop settings for a file are saved until it is removed from the playlist. 1. Press the LOOP button to show the LOOP setting area at the bottom of the display. The word by a number. Use the VALUE (+/–) buttons to set the number to – is followed LOOP TASCAM LR-10... -
Page 74: Turning Loop Playback On And Off
Ô or button to move the IN • (starting) or OUT (ending) point. (This is not possible when there is no IN (starting) and OUT (ending) point.) TASCAM LR-10 [ª] button during playback to pause, and Press the •... -
Page 75: Repeat And Single Track Playback
If you start loop playback, the switches to item, and use the VALUE (+/–) buttons to set the icon appears on the Home Screen. icon appears on the Home Screen. item automatically REPEAT if it is in a different mode. TASCAM LR-10... -
Page 76: Transferring Songs To And From A Computer
1. Connect the unit to the computer. (See “Connecting with a computer” on page 46.) 2. Click the LR-10 drive that appears on the computer to open it, revealing UTILITY and MUSIC folders. 3. Drag-and-drop the desired audio files from the computer to the MUSIC folder to copy those files to the SD card. -
Page 77: Transferring Audio Files To A Computer
11–Transferring songs to and from a computer Transferring audio files to a computer 1. Click the LR-10 drive that appears on the computer to open it, revealing UTILITY and MUSIC folders. 2. Open the MUSIC folder, and drag and drop the files that you want to copy to the desired location on the computer. -
Page 78: 12-Using The Built-In Effects
Setting the effect Press and hold the EFFECT button to open the screen. TASCAM LR-10 Use the Â/¯ buttons to select the desired item. (When selected, the setting value appears as light letters on a dark background.) Use the VALUE (+/–) buttons to change the setting value. -
Page 79: Reverb List
This reverb is modeled on a small indoor space. STUDIO This reverb is modeled on a studio-like space PLATE 1 This is a bright plate reverb. PLATE 2 This is a warm plate reverb. 12–Using the built-in effects TASCAM LR-10... -
Page 80: 13-Using The Tuner
After selecting the mode, press the TUNER button again to make settings for that mode. TASCAM LR-10 3. The first item shown for each mode is set the frequency of A between 435 Hz and 445 Hz. The setting value is shown on the right side of the screen. -
Page 81: Chromatic Tuner Mode (Auto)
OSC NOTE Set the pitch of the tuning tone (C3–B5). OSC LEVEL Set the output level of the tone between 0 and 10 (default value 7). 13–Using the tuner appears in OSC. item described above, the oscillator CALIB TASCAM LR-10... -
Page 82: 14-Using The Metronome
Set the speed to a value between minute (BPM). The default value is BEAT Set the accent frequency between accent when set to . The default value is TASCAM LR-10 LEVEL Set the metronome volume between value is Starting and stopping the metronome... -
Page 83: 15-System Settings
(Default value), item to set the time before the unit power 3min 5min 10min 30min item to adjust the display contrast. item to set the kind of batteries (alkaline batteries, default value), Ni-MH TASCAM LR-10... -
Page 84: Restoring The Default Values (Factory Settings)
1. Use the §/BROWSE and ¶/MIC buttons to select the item ( appears light on dark). QUICK FORMAT Exec TASCAM LR-10 2. Press the Á button to open a confirmation pop-up window. 3. Press the Á button to execute quick formatting. Press the [ª] button to cancel quick formatting. -
Page 85: Setting The File Name Format
Press the [ª] button to cancel full formatting. CAUTION When formatting a card, use a TASCAM PS-P520 AC adapter (sold separately), USB bus power or confirm that the batteries are sufficiently charged. If the power fails during formatting, the formatting might not occur correctly. -
Page 86: Setting The Characters In The Word Item
In addition to the alphabet and numbers, the following characters can be used: ! # $ % & ’ ( ) + , - . ; = @ [ ] ^ _ ` { } ~ The default name prefix is “ ”. LR0000 TASCAM LR-10... -
Page 87: 16-Using The Footswitch
This unit has a REMOTE jack to which you can connect a TASCAM RC-3F footswitch-type remote control (sold separately) that can be used to operate the unit. Setting footswitch operation Use the setting screen to make footswitch settings. FOOT SW 1. -
Page 88: 17-Viewing File Information
Shows information about the unit’s system settings and firmware version. When you are done, press the HOME button to return to the Home Screen, or press the MENU button to open the screen. TASCAM LR-10 File information page item and FILE file. -
Page 89: Card Information Page
Shows the amount of unused memory on the SD card. USED SIZE Shows the amount of used memory on the SD card. 17–Viewing File Information NOTE Use the ¯ button to switch between display of SIZE USED SIZE REMAIN TASCAM LR-10... -
Page 90: System Information Page
SYSTEM settings and firmware version. CUE/REV SPD Shows the speed of forward and backward searching. AUTO OFF Shows the automatic power OFF setting. BATTERY This shows the battery setting. System Ver. Shows the system firmware version. TASCAM LR-10... -
Page 91: 18-Messages
The following is a list of the popup messages that might appear on the LR-10 under certain conditions. Refer to this list if one of these popup messages appears and you want to check the meaning or determine a proper response. - Page 92 The FAT formatting of the card is abnormal or broken. This message also appears if you FAT formatted the card Format Error using a computer connected by USB and if a new card is inserted in the unit. Always use the LR-10 to conduct Format CARD FAT formatting of cards to be used with it.
- Page 93 AC adaptor (if connected). If the error message continues to appear, please Remote Cmd contact a TEAC Repair Center. Remote Rx System Err 50 System Error 1 System Error 2 System Error 3 System Error 4 Meaning and response 18–Messages TASCAM LR-10...
- Page 94 If any of these errors occur, turn the unit power OFF and restart it. If the power cannot be turned OFF, remove the batteries and disconnect the AC adaptor (if connected). If the error message continues to appear, please System Error 7 contact a TEAC Repair Center. System Error 8 System Error 9 TASCAM LR-10 Meaning and response...
-
Page 95: 19-Troubleshooting
If you are having trouble with the operation of this unit, please try the following before seeking repair. If these measures do not solve the problem, please contact the store where you bought the unit or a TASCAM Service Center. Power will not turn ON. ª... - Page 96 • I cannot erase a file. ª Is the SD card write-protect switch engaged? • TASCAM LR-10 This unit’s files do not appear on the computer. ª Confirm that the unit is connected to the computer using • its USB port.
-
Page 97: 20-Specifications
Maximum output level : +2 dBV (10 kΩ load) Maximum output : 15 mW + 15 mW (32Ω load) Built-in speaker 0.4 W (monaural) Control input/output ratings USB jack Connector : Mini-B type Format : USB 2.0 HIGH SPEED, mass storage class TASCAM LR-10... -
Page 98: Audio Performance
Windows : Windows XP , Windows Vista , Windows 7 Macintosh : Mac OS X 10.2 or later Other specifications Power Two AA batteries (Alkaline or Ni-MH) AC adaptor (TASCAM PS-P520, sold separately) USB bus power Power consumption 0.4 W (during MP3 playback) Battery operation time (continuous operation) -
Page 99: Dimensional Drawings
0 - 40°C/32°F - 104°F 20–Specifications Dimensional drawings 158 mm • Illustrations and other depictions may differ in part from the actual product. • Specifications and external appearance may be changed without notification to improve the product. 30 mm TASCAM LR-10... - Page 100 Río Churubusco 364, Colonia Del Carmen, Delegación Coyoacán, CP 04100, México DF, México TEAC UK LIMITED Phone: +44-8451-302511 Suites 19 & 20, Building 6, Croxley Green Business Park, Hatters Lane, Watford, Hertfordshire. WD18 8TE, U.K. TEAC EUROPE GmbH Phone: +49-611-71580 Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany LR-10 www.tascam.jp www.tascam.com www.tascam.com www.teacmexico.net www.tascam.co.uk www.tascam.de...