Casio 2759 Operation Manual page 3

Operation Guide 2759/3344
Alarms
You can set five independent Daily Alarms. When an
Alarm number
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
• There are six screens in the Alarm Mode. Four are for
one-time alarms (indicated by numbers from
AL1 through
(indicated by
Signal (indicated by
On/Off status
• All of the operations in this section are performed in the
Alarm time
Alarm Mode, which you enter by pressing C.
(Hour : Minutes)
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
• To set a one-time alarm, display one of the screens indicated by an alarm number
from AL1 through AL4 . To set the snooze alarm, display the screen indicated
by SNZ .
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 20 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the SNZ setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
Alarm on
2. Press A to toggle it on (
indicator
OF
( displayed).
• Turning on a one-time alarm (
displays the alarm on indicator on its Alarm Mode
screen.
• Turning on the snooze alarm (
on indicator and snooze alarm indicator on the Alarm
Mode snooze alarm screen.
On/Off status
• In all modes, the alarm on indicator is shown for any
alarm that is currently turned on.
Alarm on Snooze alarm
• The alarm on indicator flashes while the alarm is
indicator indicator
sounding.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
Module 3344
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal ( SIG
2. Press A to toggle it on (
( OF displayed).
• The Hourly Time Signal on indicator is shown on the
display in all modes while the Hourly Time Signal is
turned on.
On/Off status
Hourly time signal
on indicator
Module 3344
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Graphic Areas
The following describes the information indicated by the two graphic areas in each
mode.
Graphic area A
Graphic area B
Module 2759
AL4 ), one is for a snooze alarm
SNZ ), and one is for the Hourly Time
SIG ).
ON displayed) and off
AL1 through AL4 )
SNZ ) displays the alarm
).
ON displayed) and off
Module 3344
Mode Graphic Area A
Timekeeping Timekeeping Mode seconds
World Time Timekeeping Mode seconds
Countdown Timer Countdown time minutes
Stopwatch Stopwatch time seconds
Alarm No indication
Hand Setting No indication
Auto Return Feature
If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing when you
last exited the mode appears first.
Timekeeping
• Resetting the seconds to
00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The year can be set in the range of 2000 to 2039.
• The watch's built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch's batteries replaced.
World Time
• The World Time Mode times are calculated from the current Home City time setting
in the Timekeeping Mode, using the Greenwich Mean Time (GMT) differentials
associated with each city code.
• The GMT differential is a value that indicates the time difference between Greenwich
Mean Time and the time zone where a city is located.
• GMT differential is calculated by this watch based on Universal Time Coordinated
(UTC) data.
Illumination Precautions
This watch has an EL (electro-luminescent) panel that causes the entire display to
glow for easy reading in the dark. In any mode, press B to illuminate the display for
about two seconds.
• The electro-luminescent panel that provides illumination loses power after very long
use.
• Display illumination may be hard to see when viewed under direct sunlight.
• Illumination automatically turns off whenever an alarm sounds.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• Frequent use of illumination runs down the battery.
City Code Table
City GMT
City Other major cities in same time zone
Code Differential
– – – –11.0 Pago Pago
HNL Honolulu –10.0 Papeete
Anchorage
ANC –09.0 Nome
San Francisco, Las Vegas, Vancouver, Seattle/Tacoma,
LAX Los Angeles –08.0
Dawson City
DEN Denver –07.0 El Paso, Edmonton
Houston, Dallas/Ft. Worth, New Orleans,
CHI Chicago –06.0
Mexico City, Winnipeg
Montreal, Detroit, Miami, Boston, Panama City,
NYC New York –05.0
Havana, Lima, Bogota
CCS Caracas –04.0 La Paz, Santiago, Pt. Of Spain
RIO Rio De Janeiro –03.0 Sao Paulo, Buenos Aires, Brasilia, Montevideo
– – – –02.0
– – – –01.0 Praia
GMT
+00.0 Dublin, Lisbon, Casablanca, Dakar, Abidjan
LON London
Milan, Rome, Madrid, Amsterdam, Algiers, Berlin,
PAR Paris +01.0
Hamburg, Frankfurt, Vienna, Stockholm
CAI Cairo Athens, Helsinki, Istanbul, Beirut, Damascus,
+02.0
Cape Town
JRS Jerusalem
JED Jeddah +03.0 Kuwait, Riyadh, Aden, Addis Ababa, Nairobi, Moscow
THR Tehran +03.5 Shiraz
DXB Dubai +04.0 Abu Dhabi, Muscat
KBL Kabul +04.5
KHI Karachi +05.0 Male
DEL Delhi +05.5 Mumbai, Kolkata
DAC Dhaka +06.0 Colombo
Yangon
RGN +06.5
Bangkok
BKK +07.0 Jakarta, Phnom Penh, Hanoi, Vientiane
Singapore, Kuala Lumpur, Beijing, Taipei, Manila,
HKG Hong Kong +08.0
Perth, Ulaanbaatar
TYO Tokyo +09.0 Seoul, Pyongyang
ADL Adelaide +09.5 Darwin
SYD Sydney +10.0 Melbourne, Guam, Rabaul
NOU Noumea +11.0 Pt. Vila
WLG Wellington +12.0 Christchurch, Nadi, Nauru Is.
*Based on data as of June 2003.
Graphic Area B
Timekeeping Mode minutes
World Time Mode minutes
Countdown time seconds
Stopwatch time 1/10-second
No indication
No indication
3