Related Manuals for Siemens RUGGEDCOM APE1808
Summary of Contents for Siemens RUGGEDCOM APE1808
- Page 1 Edition 05/2022 Configuration Manual SIMATIC NET Networking Components RUGGEDCOM APE1808 (Application Processing Engine) For APE1808LNX, APE1808W10 https://www.siemens.com/ruggedcom...
- Page 2 Preface Overview Configuring and Using the RUGGEDCOM APE1808 SIMATIC NET Frequently Asked Questions Networking Components RUGGEDCOM APE1808 (Application Processing Engine) Configuration Manual For APE1808LNX, APE1808W10 05/2022 C79000-G8976-1415-04...
- Page 3 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 4: Table Of Contents
Requirements and Restrictions ................3 Security Recommendations ................... 4 Operating Temperature Range and Behavior ............6 Rebooting/Powering Down the RUGGEDCOM APE1808 Module ......6 Internal Network Interface ..................6 Default IP Addresses ....................7 RUGGEDCOM APE1808 Ethernet and Network Settings .......... 8 1.8.1... - Page 5 Table of Contents RUGGEDCOM APE1808 (Application Processing Engine) Configuration Manual, 05/2022, C79000-G8976-1415-04...
-
Page 6: Preface
Preface This guide describes how to install and configure the RUGGEDCOM APE1808 in any RUGGEDCOM RX15xx device. Its purpose is to familiarize users with the ways that RUGGEDCOM APE1808 can be used to support processing applications in RX15xx networks. It includes information about: •... -
Page 7: Related Documents
SIMATIC NET Glossary The SIMATIC NET Glossary describes special terms that may be used in this document. The glossary is available online via Siemens Industry Online Support (SIOS) at: https://support.industry.siemens.com/cs/ww/en/view/50305045 Registered Trademarks RUGGEDCOM®, ROS®, RCDP®, and RUGGEDCOM Discovery Protocol® are registered trademarks of Siemens Canada Ltd. -
Page 8: Third Party Copyrights
Siemens customer service representative. Training Siemens offers a wide range of educational services ranging from in-house training of standard courses on networking, Ethernet switches and routers, to on-site customized courses tailored to the customer's needs, experience and application. -
Page 9: Customer Support
Preface Customer Support Customer Support Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or general information, contact Siemens Customer Support through any of the following methods: Online Visit http://www.siemens.com/automation/support-request to submit a Support Request (SR) or check on the status of an existing SR. -
Page 10: Overview
USB Ports Reset Button Power LED Figure 1.1 RUGGEDCOM APE1808 Module Operating System The RUGGEDCOM APE1808 is available with one of the following operatings systems pre-installed: • Debian Linux® • Microsoft Windows® 10 Enterprise 2019 LTSC RUGGEDCOM APE1808 (Application Processing Engine) - Page 11 SD card. Other Software/Applications Siemens does not support any software installed on the RUGGEDCOM APE1808. This includes, but is not limited to, software images provided by Siemens Customer Support. Linux and SD Card Support By default, the Linux-based version of the RUGGEDCOM APE1808 does not support SDXC or SDUC microSD cards (i.e.
-
Page 12: Requirements And Restrictions
Overview 1.2 Requirements and Restrictions Windows Licensing To run Windows® 10 Enterprise 2019 LTSC on the RUGGEDCOM APE1808, the Windows® operating system must be activated after the RUGGEDCOM APE1808 module has been installed. For more information, refer to the product key sticker (included in the product packaging) and Windows®... -
Page 13: Security Recommendations
Modules (24 W) Are Installed USB Storage Devices • USB storage devices used with the RUGGEDCOM APE1808 must have USB 3.0 Interfaces. Other peripheral devices, such as keyboards and mice, may have USB 2.0 or 3.0 interfaces. SD Card Usage •... - Page 14 Authentication • When using the Linux-based version of the RUGGEDCOM APE1808, as per the local environment’s security policy, add an administrative account, disable the root user on Debian Linux, and replace any default passwords. For a list of default user profiles and passwords, refer to "Logging in to RUGGEDCOM...
-
Page 15: Operating Temperature Range And Behavior
APE1808 features an internal gigabit Ethernet interface on the back of the module that interfaces with the host RUGGEDCOM RX15xx device. The interface can be used by the operating system running on the RUGGEDCOM APE1808 as a normal network RUGGEDCOM APE1808 (Application Processing Engine) -
Page 16: Default Ip Addresses
IMPORTANT Interface settings configured via RUGGEDCOM ROX II must be mirrored within the RUGGEDCOM APE1808 module. For instance, if a VLAN is assigned to the module in RUGGEDCOM ROX II, a corresponding VLAN must also be configured via the module's operating system. -
Page 17: Ruggedcom Ape1808 Ethernet And Network Settings
(such as the RUGGEDCOM APE1808) in switch.0001 to reach services on the control module and network management. In this situation, the RUGGEDCOM APE1808 can be assigned an unused IP address in subnet 192.168.0.0/24 and communicate with other devices in VLAN1 at a bridging and routing level. -
Page 18: Example: Rx15Xx Services And Wan Networking
When operating the RUGGEDCOM APE1808 in either switch or router mode, the RUGGEDCOM RX15xx will issue RSTP BPDUs to the RUGGEDCOM APE1808. If you do not wish the RUGGEDCOM APE1808 to receive these BPDUs, they may be disabled in RUGGEDCOMRUGGEDCOM APE1808 in the interface switch menu for the RUGGEDCOM APE1808 interface. -
Page 19: Decommissioning The Module
1.9 Decommissioning the Module Figure 1.4 Example Configuration In this scenario, the RUGGEDCOM APE1808 is reached via a routed interface. This is accomplished by moving the RUGGEDCOM APE1808 port onto its own VLAN, and creating a point-to-point connection between it and the control module. - Page 20 From the operating system, use standard erasure tools to erase data on the module that represents the RUGGEDCOM APE1808's flash memory. For example, use standard Linux tools, such as dd, wipe, or shred, to wipe data from the module.
- Page 21 Overview 1.9 Decommissioning the Module RUGGEDCOM APE1808 (Application Processing Engine) Configuration Manual, 05/2022, C79000-G8976-1415-04...
-
Page 22: Configuring And Using The Ruggedcom Ape1808
The following sections describe how to configure and use the RUGGEDCOM APE1808: IMPORTANT Before using the RUGGEDCOM APE1808, create a backup image that can be restored should the module be configured improperly. Warranty does not support modules rendered inoperable/inaccessible due to configuration errors made by the user. -
Page 23: Setting The Root And User Passwords (Linux Only)
Where: • { user } is the user name (e.g. root, admin, operator, guest, etc.) Setting the BIOS Password A password for the RUGGEDCOM APE1808 BIOS is not set by default. RUGGEDCOM APE1808 (Application Processing Engine) Configuration Manual, 05/2022, C79000-G8976-1415-04... -
Page 24: Disabling Alternative Boot Options
2.5 Disabling Alternative Boot Options To set the BIOS password, do the following: IMPORTANT If the BIOS password is lost, the module must be returned to Siemens for service. For more information, contact Siemens Customer Support. This service is not supported by warranty. -
Page 25: Setting The Grub Bootloader Password
Configuring and Using the RUGGEDCOM APE1808 2.6 Setting the GRUB Bootloader Password Setting the GRUB Bootloader Password To set the GRUB bootloader password, do the following: IMPORTANT Use strong passwords. Avoid weak passwords such as password1, 123456789, abcdefgh, etc. Login or gain root access. -
Page 26: Setting The Hard Drive Password
Lost IP Address The simplest resolution to this problem occurs when the RUGGEDCOM APE1808 is easily reached and a monitor is attached. The RUGGEDCOM APE1808 can be queried for the IP address and the configuration of the RUGGEDCOM APE1808 or command module may be changed to allow networking. - Page 27 If your RUGGEDCOM APE1808 does not boot, ensure that it is not disabled. If you are installing an RUGGEDCOM APE1808 to act as a spare, you may wish to disable the RUGGEDCOM APE1808 to reduce power.
-
Page 28: Frequently Asked Questions
How do I power a USB DVD-ROM drive or USB hard disk using the RUGGEDCOM APE1808 USB port? The RUGGEDCOM APE1808 USB port is limited in the amount of power it can provide. Use a powered hub to employ devices such as these. - Page 29 Frequently Asked Questions RUGGEDCOM APE1808 (Application Processing Engine) Configuration Manual, 05/2022, C79000-G8976-1415-04...
- Page 30 For more information Siemens RUGGEDCOM https://www.siemens.com/ruggedcom Industry Online Support (service and support) https://support.industry.siemens.com Industry Mall https://mall.industry.siemens.com Siemens Canada Ltd. Digital Industries Process Automation 300 Applewood Crescent Concord, Ontario, L4K 4E5 Canada © 2022 Siemens Canada Ltd. Subject to change...