Samsung LN40C530 Quick Setup Manual page 2

Step 5 :
Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process. It also
displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right
arrow buttons on your remote. To make a selection, press the
enTerE
button. To skip a screen, press the MenU button.
To turn on your TV, press the POwer button on the remote or press the
button on the TV. To run Plug & Play, follow these steps:
POwer
Plug & Play
Select language of the OSD.
english
español
language : english
Français
U Move E enter
1. On the Language screen, select the language for the On Screen Display
(OSD) using your remote control, and then press enTerE
Home Use screen appears.
2. Select Home Use, and then press enTerE button. If you select Store
Demo, the TV will reset your picture and audio settings every 30 minutes. After
you press enTerE button, the Antenna Source screen appears.
3. If your TV is only attached to an antenna, select Air. If your TV is only
attached to cable and you have no cable box, select Cable. If your TV is
attached to an antenna and cable with no box, select Auto. When done,
press enTerE button on your remote. The Select Cable System screen
appears.
IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps
3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4,
according to the directions for your cable or satellite box.
4. If your TV is attached to a cable system and you have no cable box, you
must select your cable system type. If you have Digital cable, you must
select the cable system type for both Analog and Digital.
Remote Control Buttons and Functions:
✎
This is a special remote control for the visually impaired persons and has Braille points on the Power, Channel, Volume buttons.
Turns the TV on and off.
Press number buttons for direct access to channels.
Press to select additional digital channels broadcast by
the same station. For example, to select channel 54-3,
press 54, press -, and then press 3.
Adjusts the volume.
Displays the channel list on the screen.
View the Media
Quickly selects frequently used functions.
Selects the on-screen menu items and changes the
values seen on the menu.
Return to the previous menu.
Colored buttons for use in the
Channel List, Media Play
menu, etc.
Use these buttons in the Media Play and Anynet+ modes.
( : Controls recording on Samsung recorders with the
Anynet+ feature)
BN68-02610A-Eng.indd 2
After you have selected the cable system type, select Start, and then
press the enTerE button on your remote.
Most cable systems are Standard (STD) systems. If you are not sure
✎
about what kind of cable system you have, contact your cable company.
5. The TV memorizes the available channels. This process can take up to 45
minutes. After the TV has memorized the channels, the Clock Mode screen
appears.
6. Choose the Clock Mode. Select Auto if you have a digital channel in your
area. Select Manual if you don't, or if you have a cable or satellite box. When
done, press enTerE button. The Daylight Savings screen appears.
If you select Manual, the clock setting screen appears.
✎
7. Select the daylight saving time setting: Off, On, or Auto, and then press
enTerE button.
8. After the time zone screen, The connection method for best HD screen quality
is displayed. Press Right arrow button on your remote to view each screen in
succession. Press the Blue button to skip this section.
9. The enjoy your TV screen appears. and then press
button. The
Basic Functions
Selecting a Source
To watch a movie on your Blu-ray player or watch
your favorite TV show, you must select the correct
source. A source is a device, such as a Blu-ray/DVD
player, a cable/satellite box, antenna or a cable TV
input. Sources can be connected to your TV through
the HDMI, DVI, Component, Composite, or D-sub
connections, or through the Antenna or Cable In
connections.
To view the signal from a source connected to the HDMI, DVI, Component,
Composite, or D-sub jack, press the SOUrCe button on your remote. Each time
you press the SOUrCe button, you change to a different source.
Press to switch between the sources (Blu-ray player,
cable box, DVD player, etc.) connected to your TV.
Return to the previous channel.
PRE-CH
Cut off the sound temporarily.
Change channels.
CHLIST
Displays the main on-screen menu.
MENU
MEDIA.P FAV.CH Displays Favorite Channel Lists on the screen.
Play.
TOOLS
Press to display information on the TV screen.
INFO
RETURN EXIT
Exit the menu.
S.MODE SLEEP MTS
S.MODe: Selects the sound mode.
P.MODE P.SIZE CC
SleeP: Setting the Sleep Timer.
MTS: Press to choose stereo, mono or Separate
Audio Program (SAP broadcast).
P.MODe: Selects picture mode.
P.SIze: Choose the picture size.
CC: Controls the caption decoder.
Changing the Screen Size
Your TV has several screen size options, each designed to work best with specific
types of video input. If you have a cable box or satellite receiver, it may have its own
set of screen sizes as well.
To change the screen size, press the P.SIze
you press it, your TV displays the current setting. There after, each time you press
the P.SIze button, you change the size of the picture on the screen.
The following sizes are available:
16:9 Wide screen Zoom 1
enTerE button.
Wide Fit 4:3 Standard screen
Screen Fit displays a full HD picture covering the entire screen with no cutoff
✎
on any side. It is only available when your TV inputs an HDMI (720p, 1080i,
1080p), Component (1080i, 1080p), or DTV (over-the-air 1080i) signal.
Changing the Picture Mode
Your TV has four preset Picture Modes with factory adjusted settings, each
designed to give you an excellent picture under specific conditions.
The Picture Modes are listed and described in the table below:
Mode Description
Brightens picture. For a vibrant, enhanced image in brightly lit or
Dynamic
sunny room.
Standard For a bright, detailed picture in a normally lit room.
PRE-CH
natural For a comfortable, easy-on-the-eyes picture in a normally lit room.
Movie For a studio quality cinema picture in a dimly lit or dark room.
To change the Picture Mode, follow these steps:
CHLIST
1. With the TV on, press the TOOlS button on your remote.
MENU
The Tools menu appears.
MEDIA.P FAV.CH
2. Using the ▲ or ▼ on your remote, select Picture mode.
TOOLS
INFO
3. On the Picture Mode menu, use the ◄ or ► on your remote to select the
Picture Mode you want.
4. Press the exIT button to exit the menu.
RETURN EXIT
Viewing the On Screen Menus
S.MODE SLEEP MTS
To view the On Screen Menus, follow these steps:
P.MODE P.SIZE CC
1. With the power on, press the MenU
on your remote. The main menu appears.
The menu's left side has the following menu
options: Picture, Sound, Channel, Setup,
Input, Application, and Support.
Press the ▲ or ▼ button on your remote
2.
to select a menu option, and then press the
button.
enTerE
3. When done using the menu, press the
English - 2
Changing Channels and Adjusting the Volume
Volume
CHLIST
button on your remote. The first time
MENU
MEDIA.P
Adjust the volume by pressing the
y button on the remote.
TOOLS
RETURN
You can also change the
S.MODE SLEEP
channels by pressing the
Zoom 2
P.MODE P.SIZE
z buttons on
the front panel of your TV
and adjust the volume by
pressing the y
buttons.
Screen Fit
Setting the Clock
Before you can use your TV's On/Off Timer, you must set the clock. To set the
clock, follow these steps:
1. Turn on your TV.
2. Using your remote, press the
button on your remote.
Then, select Setup → Time.
3. Select Clock Mode, and then press
the enTerE button. Set Clock
Mode to Auto or Manual.
Select Auto if you have a digital
✎
channel in your area and are not
using a cable/sat box.
When you set Clock Mode to Manual
4. Select Clock Set, and then press the
appears.
5. Using the number buttons on your remote, enter the Month, Day, year, Hour,
and Minute. Use the ◄ or ► button to move between entry fields.
6. Press the reTUrn button on your remote when done.
Connecting a USB Device for Media Play
PRE-CH you can enjoy photo, music, and movie files
stored on a USB device by connecting it to the TV
and using the Media Play feature. To connect a
USB device for Media Play, follow these steps:
1. Turn on your TV.
CHLIST
MeNu
2. Connect a USB device
button
containing photo, music and/
MENU
MEDIA.P FAV.CH
or movie files to the USB (HDD)
jack on the side of the TV.
TOOLS
INFO
3. When the Application selection
screen appears, press the
enTerE button on your
remote to select Media Play
EXIT
RETURN
(USB).
exIT button on your remote to exit.
S.MODE SLEEP MTS
P.MODE P.SIZE CC
PRE-CH PRE-CH
Channel
CHLIST
FAV.CH MENU
Change the channels by pressing MEDIA.P FAV.CH
the z button on the remote.
TOOLS
INFO
INFO
If your TV is attached to a cable
✎
or satellite box, you change the
channel using the box's remote.
EXIT
RETURN EXIT
MTS
S.MODE SLEEP MTS
CC
P.MODE P.SIZE CC
Remote control sensor Power Indicator
Clock Set
MenU
Month Day year
-- -- ----
Hour Minute am/pm
-- -- --
Move Adjust Enter Return
L U E R
enTerE button. The Clock Set screen
TV Side Panel
uSB Drive
MediaPlay
Videos
SUM A Change Device View Devices E enter R return
D
BN68-02610A-01
2010-02-11 11:30:29