Contents Specifications…………………………………………………………………………………………3 Function Test …………………………………………………………………………………………4 Back Up User’s Data …………………………………………………………………………………9 Recovering the Factory Default …………………………………………………………………….11 Special function start up ……………………………………………………………………………12 Circuit Check Specifications ………………………………………………………………………15 PCB Parts Layout and Pattern ……………………………………………………………………16 Circuit Diagram …………………………………………………………………………………… 17 Exploded view ………………………………………………………………………………………20 Parts List ……………………………………………………………………………………………22 Spare Parts Order List ………………………………………………………………………………28 Spare Parts Order Sheet ……………………………………………………………………………30 Supplement: Identification of main PCB ………………………………………………………………31...
Function Test Starting in “Test mode” 1) Start up the G1X in the following ways using the AC adaptor AD-0006. a) Connect AC adaptor holding the [BANK UP・TAP] key (SW1) and [RHYTHM] key (SW2). b) Connect AC adaptor when Ground and the test point TP1.
Page 5
Inspection judgment standard of 16 click setting. ⑩ ⑨ ⑪ ①③⑤~⑮⑰⑲ ⑧ ※A value changes in ⑫ a range of arrow ⑦ ⑬ ②④⑯⑱ ⑥ ※It is NG that a ⑭ value changes in a click. 0->1、2->1 ④ ⑯ ⑤ ⑮...
Page 6
6. PEDAL ASSIGN check Press the PEDAL ASSIGN key, and make sure that the 7segment LED is displayed [SL]. And make sure that the PEDAL ASSIGN LED turns on in the order of “VOL ->WAH -> DRY ->MOD ->DLY ->REV -> turns off”, whenever the key is pressed. 7.
Page 7
11. Restoring Factory Defaults 1) Power on in normal mode. If 7segment LED doesn't blink “AL", power on pressing the "STORE" key. Note) If someone make the operation below, after that 7segment LED never show "AL" 2) Make sure that display blinks “AL” 3) Press [STORE] key (SW3) and display indicates “ok”.
Page 8
Make sure that the 7 segment LED indication returns to the previous state. 15. Stability Put the G1X on a surface plate, and push it diagonally. Make sure that there is no remarkable space (less than ±0.3 mm is acceptable).
Back Up User’s Data If necessary, back up the user’s effect patch data to avoid an accidental erasing. Required · User’s G1X as a transmitter (hereinafter referred to as “the transmitter”) · Another G1X as a receiver (hereinafter referred to as “the receiver”) ·...
Page 10
6. Press the [BANK UP・TAP] key (SW1) of the receiver, and make sure that the 7 segment LED lit “rx”. The receiver is ready to receive the data. 7. Press the [Rhythm] key (SW2) of the transmitter and make sure that the 7 segment LED lit “tx”.
Recovering the Factory Default In the factory default condition, the patches of the user area (A0-d9) contain the same settings as the patches of the preset area (00-39). Even after overwriting the user patches, their original content can be restored in a single operation (“All Initialize”...
1. Special function and how to start up There are some methods to start up the G1X for service. up the G1X in the following ways using the AC adaptor AD-0006 or All special functions start connecting the plug into INPUT connector (J2) when set the battery.
Page 13
Make sure “ok” appears on the 7 segment LED. 6) Make sure that the following indications appear on the 7 segment LED. When the 7 segment LED is correctly displayed, Restart the G1X by press the [BANK UP・TAP] key (SW1).
Page 14
Serial No. 022151 – Make sure “12” appears on the 7 segment LED. 3) Restart the G1X by press the FOOT SWITCH [^] (SW5) or [v] (SW4) again. ● Revision The 7 segment LED is displayed system revision of the G1.
Circuit Check Specifications Items Specifications Inputs Conditions/notes Display and Indicator Keys pressed in "Test mode" Current consumption 125mA±20mA Short Immediately after Test mode starts All LEDs are lit. All lit None (Start up) Power supply voltage 3.3VA 3.3V±0.15V Short Immediately after Test mode starts All LEDs are lit. All lit None(Start up) +3.3VD...
Page 24
G1X JAN Bar-Code Label Z8F-0093-A4 for 120GL G1X JAN Bar-Code Label Z8F-0093-A4 for 220BX G1X JAN Bar-Code Label Z8F-0093-A4 for 240UK G1X USA Bar-Code Label for Gift Box G1X USA Bar-Code Label for Carton Box FCC Label Z2I-0729 Aluminum label Destination Label...
Page 25
Parts List *Serial No. 022151 - MAIN PCB Partslist PCB-0180 No. NAME SUB SPECIFICATIONS DESCRIPTION REFERENCE No. Q'ty UPD78F0537GB(T)-UEU-A LQFP-64pin 10x10 UPD78F0537GB(T)-601-UEU-A LQFP-64pin 10x10 ZFX-3 LQFP-176pin 0.5-26X26 SDRAM P2V16S406TP-6G TSOP-50pin SDRAM IS42S16100C1-7TL TSOP-50pin SDRAM RMS116T(LF)-7A TSOP-50pin SDRAM EM636165TS-7G TSOP-50pin AD/DA WM8734SEFL/R QFN-28pin 5x5 LOGIC IC...
Page 27
G1X JAN Bar-Code Label Z8F-0093-A4 for 120GL G1X JAN Bar-Code Label Z8F-0093-A4 for 220BX G1X JAN Bar-Code Label Z8F-0093-A4 for 240UK G1X USA Bar-Code Label for Gift Box G1X USA Bar-Code Label for Carton Box FCC Label Z2I-0729 Aluminum label Destination Label...
Spare Parts Order List The parts with ''*'' are available from G1X G2Series=G2, G2.1u, B2, B2.1u, A2, A2.1u CODE No. PART NAME SPECIFICATIONS DESCRIPTION Q'TY PRICE (Japanese yen) PCB ASSEMBLY SP40175 G1X Main PCB assy PCB-0180, PCB-0181 FR-4 2layer,138.2mm x 92mm (PCB-0180, include PCB-0181)
Page 29
FCC Label Z2I-0729 G7.1ut, G9.2tt, G1, B1, G2Series,GFX-1,GFX-3,MRT-3B,MRS-4B CARD, SHEET SP00984 Warranty Card US Z2I-0730 G1, B1 SP02378 G1/G1X Patch List Sheet Z2I-0725 SP02406 G1X Logo Label for Unit Z2E-0220 SP02380 G1/G1X Display signal chart sheet Z2I-0726 - 29 -...
To: ZOOM Corp. Overseas Sales Group page of Parts Order Sheet Code No. Product name Parts name Specifications Unit price ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥...
Supplement: Identification of main PCB Main PCB is common use for other production. Therefore, this main PCB has check box to identify which production will be used for. See below figure, it shows check box location on the main PCB. Bottom Layer Check box on the main PCB - 31 -...
Supplement : The major difference between before No.022150 and after No.022151 before No.022150 after No.022151 Page Contents Item Function test 5.Product number "87" or "11" "d2" Special start up Version Special start up Revision Exploded view 20, 21 No.37 Refrect rubber Optical interception cover Partslist 24, 27...
Page 33
G1X Service Manual Change History Date Page Change 22 Jun 2007 28-29 Complete price list...