Download Print this page
Rinnai RHFE-1510F Operating And Installation Instructions
Rinnai RHFE-1510F Operating And Installation Instructions

Rinnai RHFE-1510F Operating And Installation Instructions

Forced flued heater

Advertisement

Quick Links

has
17.4
13.6
,
T
MAINTENANCE
TROUBLESHOOTNG THE HEATER
5
11
12
15
27
28
29
30
31

Advertisement

loading

Summary of Contents for Rinnai RHFE-1510F

  • Page 1 17.4 13.6 MAINTENANCE TROUBLESHOOTNG THE HEATER...
  • Page 2: Warranty

    Warranty As the purchaser of this high quality Rinnai Space Heater you are provided with the following conditional warranty. Heat Exchanger: 5 years* All other Parts: 1 year Labour: 1 year *Full Heat Exchanger replacement (parts only) in the first five years, thereafter reducing as follows, subject to conformity.
  • Page 4 lue Terminal Position Minimum Distances Dimen- Terminal Position sion Directly below an opening, air brick, opening windows, etc. Above an opening, air brick , opening window, etc. Horizontally to an opening, air brick , opening window, etc. Below gutters, soil pipes or drain pipes. Below eaves.
  • Page 5 the instructions Flue is not designed to be positioned under floor, or below the level of the heater. Flue terminal must be kept clear of obstructions and plants because the combustion gases and vapour come out from flue terminal. Flue terminal must be kept clear of bags or empty cans so it does not get blocked. type and pressure are compatible with the appliance.
  • Page 6 Swing Louvre point. Alternatively, remove plug and wire into a double-pole switched, 3A fused, spur. Warm air Open the gas valve fully. Flue Terminal Dirty damage...
  • Page 7 Locking the control panel will prevent people tampering with the adjustments. If lock lamp is on, the control buttons will not alter the operation of the heater. (For Safety, if you push the stop button during operation, the heater will stop.) To alter the heater, you must cancel the lock function.
  • Page 8 Connection Manifold Sleeve Plate Terminal Body...
  • Page 9 - 400 must be used...
  • Page 10 Connect flexible hose to heater and tighten band with screw driver. Connect air inlet hose to the flue manifold. Tighten band with screw driver to secure hose Connect the extendable flue tube to the exhaust port of the flue manifold. Adjust the length of the extendable tube to meet exactly with the flue hole height.
  • Page 11 Sleeve plate Flue Tube of Unit Put grease on connecting O-rings. Use the same air inlet hose length as the length of the flue manifold. Example of flue tube extension Connection Manifold stop end stop end Concentric Port Flue Tube of Unit Flue Tube stop end of Unit...
  • Page 12 Separate the Terminal into 3 parts; sleeve plate, connection manifold, and the terminal body. This is done by pulling the outside terminal from the connection manifold, then pull sleeve off outer terminal. Spread springs out so they are slightly bigger than the hole. Push the terminal body through from outside.
  • Page 13: Iring Diagram

    esting the Unit iring Diagram Purge air and sw arf f rom gas line. Connect gas (1/2 inch BSP). Connection can be easily reached from the top rear of the unit. Check for escapes, using soapy water after turning gas on. Remove fan filters.
  • Page 14 If controlled by a central timer, dip switch 3 must be in the ON position. To use a time clock you will also require a transformer and sub PCB available from Rinnai. When a time clock is used the appliance On/Off button will not operate.
  • Page 15 AINTENANCE Repeat the attempt from occurs dust this Rinnai UK. Do not attempt to disassemble or repair the product unless trained to do so.
  • Page 16 ROUBLESHOOTING THE HEATER Refer to the list below. Rinnai UK . plate. 17.4 1/2 in BSP...
  • Page 17 Our service personnel are fully trained and equipped to give you the best service on your Rinnai appliance. If you require service please ring the contact number on this page. 9 Christleton Court Manor Park Runcorn WA7 1ST 01928 531 870 01928 531 880 www.rinnaiuk.com...
  • Page 18 RHFE-1510F CUSTOMER OPERATING INSTALLATION INSTRUCTIONS Read the user's instructions before lighting the appliance. This appliance shall be installed in accordance with these Manufacturers Installation Instructions, Local Gas Fitting Regulations, any other relevant Statutory Regulation, and must be installed, serviced and removed by an authorised Person.