Furuno 1722 Quick Start Manual page 2

NAVNET QUICK SETUP GUIDE
STEP 1
(Confirm no simulator modes are selected [SIM] would be displayed in upper left corner of display)
Connect the GPS position source. Use the Furuno BBWGPS antenna, Furuno GP32 or any compatible external device
(must output NMEA sentences GGA, VTG, ZDA,
BBWGPS (only configure if the BBWGPS antenna is connected to DATA1)
BBWGPS
1. Press "MENU", Select [SYSTEM CONFIGURATION], Select [NAV OPTION]
2. Select [NAV SOURCE SETTINGS], Change POSITION SOURCE to [FURUNO BB GPS]
3. Press "RETURN"
4. Select [GPS SENSOR SETTINGS], Select [WAAS SETUP], Set [WAAS MODE], [ON]
5. Press "RETURN" three times
6. Select [SYSTEM SETUP], Select [PORT SETUP], Select [GPS/NMEA PORT] , Set FURUNO GPS SENSOR to [YES]
7. Press [RETURN], then [MENU] for normal operations
OR
cable included/attached
to the BBWGPS
Use supplied GP32 cable
(I/O) and part # 000-144-418
Radar antenna
connection
(GP1700C, N/A)
DATA 1
DATA 2
000-125-237 cable
supplied with PG1000
or use a # 000-117-603
cable to connect to a
external heading device
Heading device (optional)
Furuno PG1000
OR
other external
(required for overlay)
AD10 Furuno format
required for ARP11
radar autoplotter option
POWER OFF then ON after any "MENU CHANGES" to store the new information.
Refer to the "Wiring configurations (7 inch display notes)" or "General Information" page for details
7 inch series, single display
use the NavNet display "default" menu settings if connecting
FURUNO GP32
an external GPS device (example: Furuno GP32 shown)
OR
other external GPS
12-24 VDC
cable to connect
DATA 3 output to
optional autopilot
or other device is
available, see wiring
configurations page
(7" display NOTES)
NETWORK
000-144-422
(5m) cable
supplied
w/BBFF1
12-24 VDC
BBFF1 SOUNDER
12-24 VDC
STEP 3
BBFF1 Network sounder if Installed (Plug and Play)
Connect the BBFF1 network sounder to the display "network port" using the
supplied blue 000-144-422, 5m network cable
BBFF1(if installed): Displaying digital temperature and depth on NavNet display(s)
Press [MENU], [SYSTEM CONFIGURATION]
[GENERAL SETUP] (default is [NMEA] for displaying input from external depth and temperature devices)
TEMPERATURE SOURCE [ETR] (transducers with temperature sensor only)
DEPTH SOURCE [ETR]
see manufacturer specifications
STEP 2
Applies to Radar only (Omit if installing a plotter)
Connect the radar antenna to DJ1 of the radar display 1722/C, 1732/C,
1742/C or 1762/C
RADAR SETUP PROCEDURES:
NOTE: Installation Menu access required.
Press and hold [MENU] while powering on display (starts normally)
Press [MENU], [SYSTEM CONFIGURATION], [INSTALLATION SETUP]
Press [RADAR SETUP] these are REQUIRED ADJUSTMENTS!
ANTENNA TYPE
A 1722 / 1722C
B 1732 / 1732C
C 1742 / 1742C
F 1762 / 1762C
ANTENNA ROTATION [ROTATE] (do not change)
TRANSMIT RADAR FOR 5 minutes prior to and continue for FOLLOWING
PROCEDURES (on the shortest range, set gain & sea control properly)
TUNING [OFF] Press [EDIT], select [ON], Press [ENTER], when complete
"NOW TUNING" disappears.
TIMING ADJUST [OFF]
target, rotate knob to straighten target, Press [ENTER].
HEADING ADJUST (NOTE: factory setting 180° out for 24" dome antennas)
select [NEXT PAGE], HEADING ADJUST [OFF], Press [EDIT], select [ON], using
a range between 0.125-.25nm, rotate knob to bisect radar target, Press [SET]
Maximum radar ranges may need to be turned on using [MENU],
[RADAR RANGE SETUP], after "ANTENNA TYPE" is changed
(with optional equipment shown)
).
Press [EDIT], select [ON], visually select long straight