Related Manuals for IBM 0367
Summary of Contents for IBM 0367
- Page 1 AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable Instruction V ersion 4 SENG-0367-04...
- Page 3 AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable Instruction V ersion 4 SENG-0367-04...
- Page 4 This edition applies only to reduced instructions set computer (RISC) systems. © Copyright International Business Machines Corporation 1998, 2000. All rights reserved. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.
-
Page 5: Safety And Environmental Notices
These circuits meet the standard limits described in International Electrical Commission (IEC) 664, installation category II. It is the customer’s responsibility to ensure that the power outlet meets the standards of IEC 664, installation category II. (RSFTC214) © Copyright IBM Corp. 1998, 2000... - Page 6 IBM at 1-800-426-4333. Please have the IBM part number that is listed on the battery available when you make your call. For information on battery disposal outside the United States, contact your local waste disposal facility.
-
Page 7: Installation Instruction
Installation Instruction The prerequisite for the Operations console cable (feature number 0367) is the 2721 or 2745 card. If you need to install a 2721 or 2745 card, install it first, then return to these instructions. Ensure that your AS/400 Operating System is V4R3M0 or later. - Page 8 __ d. Click on Network. __ e. Is TCP/IP listed? ↓ Click on OK. You have satisfied the network requirements. Go to step 2m on page 3. AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
-
Page 9: Installing The Cable
__ f. Click on Add. __ g. Select Protocol. __ h. Click on Add. __ i. Select Microsoft listed under ″Manufacturers″. __ j. Select TCP/IP listed under ″Network Protocols″. __ k. Click on OK twice. __ l. Select Yes to restart the PC. __ m. - Page 10 __ 11. Disconnect the system unit console cable (Figure 2 on page 5) that is connected to Port 1 (right connector). Disconnect the other end of the cable from your PC. The cable will not be used. AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
- Page 11 Figure 2. Port 1, Position C08 __ 12. Disconnect the electronic customer support cable from Port 0 (left connector). Reconnect the electronic customer support cable to Port 1 in position C08 (right connector). Be sure to label the cable C08/Port 1. __ 13.
- Page 12 21. __ 21. Install the system unit back cover __ 22. Plug the AS/400 system unit into an electrical outlet. AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
- Page 13 __ 4. Click on Settings. __ 5. Click on Control Panel. __ 6. Click on Add/Remove Programs. __ 7. Is IBM AS/400 Client Access for Windows 95/NT shown? ↓ Click on OK. Go to step 10. Click on IBM AS/400 Client Access for Windows 95/NT.
- Page 14 For more information on installing, go to the Client Access for Windows 95/NT - Setup book. Click Yes or Finish, if prompted to restart. __ 21. Are you using the Windows 95 platform? AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
- Page 15 ↓ You are using the Windows NT platform. If you are only using the Remote Control Panel, go to “Windows NT Local Controlling System (LCS)” on page 16. Otherwise, go to “Installing Windows NT Console Support” on page 14. If you are only using the Remote Control Panel, go to “Windows 95 Local Controlling System (LCS)”...
- Page 16 Next to exit that online display and continue with the next step. __ o. Click on Finish. AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
- Page 17 __ p. Click on Properties. Set Maximum speed to 115200. Click on OK. __ q. Click on Close or OK. __ r. Go to “Windows 95 Local Controlling System (LCS)”. Windows 95 Local Controlling System (LCS) __ 1. Did you install only a Remote Control cable (part number 97H7591)? ↓...
- Page 18 12 on page 13. Otherwise, go to the following Note. Note: If you chose Console only on the Actions display, you would not get any of the Remote Control Panel displays here. AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
- Page 19 If you chose Remote Control Panel only, you would not get any of the Console only displays here. __ 11. Click on Next to allow the system to detect the console communications port. System should find the port and select it automatically. If not, manually select.
- Page 20 C:\Programs Files\IBM\Client Access\Aoc\Inf Press the Enter key. __ c. Click on OK. The entry AS/400 Operations Console Connection should be shown. __ d. Click on Next. AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
- Page 21 __ e. Select the communications port that you installed the console cable into. (For example, Com1.) __ f. Click on Next. Note: The first time a modem is configured on a PC, a display will appear asking you for your telephone area code or country code and any numbers necessary to access an outside line.
- Page 22 __ a. Does a B M appear in the Function/Data display? ↓ Go to step 3g on page 17. __ b. Is the Function/Data display lit? ↓ Before calling your hardware service representative, do the following: AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
- Page 23 v Confirm that the electrical outlet is functioning by plugging in a lamp or other simple device. v Ensure that the power cord is securely plugged into the system unit and electrical outlet. __ c. Press the Up or Down select push button until 02 appears in the Function/Data display.
- Page 24 __ 17. Did you configure Operations Console for a Remote Control Panel? ↓ Go to step 19 on page 19. __ 18. Did the Remote Control Panel appear when setup was finished? AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
- Page 25 ↓ Recheck the cables and Operations Console setup. Then go to step 17 on page 18. If your AS/400 system unit will be using a twinaxial console, ensure that the console is powered on. Use the Remote Control Panel to power on the AS/400.
-
Page 26: Completing The Installation
7) Go to step 1d. d. Power on the PC that is your console. e. Press the system unit power-on button. The power-on light will appear. AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5... - Page 27 Information Center. You can access the Information Center from the AS/400 Information Center, SK3T-2027-03 or from the following Web site: http://www.as400.ibm.com/infocenter __ 5. Your feature upgrade is complete. Keep all miscellaneous parts, such as wrap connectors, with the Service Materials box or in a safe place.
- Page 28 AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
- Page 29 Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any IBM intellectual property right may be used instead.
- Page 30 Avis de conformité à la réglementation d’Industrie Canada Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Community Compliance Statement AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
- Page 31 Attention: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Trademarks The following terms are trademarks of the IBM Corporation in the United States or other countries or both: AS/400 AS/400e series...
- Page 32 AS/400e 170 or 250 0367 Operations Console and 0381 Remote Control Panel Cable V4R5...
-
Page 33: Readers' Comments - We'd Like To Hear From You
No Thank you for your responses. May we contact you? When you send comments to IBM, you grant IBM a nonexclusive right to use or distribute your comments in any way it believes appropriate without incurring any obligation to you. - Page 34 Readers’ Comments — We’d Like to Hear from You Cut or Fold Along Line SENG-0367-04 Fold and Tape Please do not staple Fold and Tape _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _...
- Page 36 Printed in the United States of America on recycled paper containing 10% recovered post-consumer fiber. SENG-0367-04...