Related Manuals for LG UW760H Series
Summary of Contents for LG UW760H Series
- Page 1 INSTALLATION MANUAL LED TV* * LG LED TV applies LCD screen with LED backlights. Please read this manual carefully before operating your set and retain it for future reference. UW760H* www.lg.com...
-
Page 2: Table Of Contents
LANGUAGE & COUNTRY SELECTION - Power On Default - Automatically for Setup - Aux Source Setting - Manually for Setup - Power Management - USB LG Smart Install Utility - Factory Reset NETWORK - MAC Address - Network Setting - IP Stream Control... -
Page 3: Location And Function Of Controls
LOCATION AND FUNCTION OF CONTROLS LOCATION AND FUNCTION OF CONTROLS Parts and Button Screen Remote control and Intelligent sensors Power Indicator Dome Button Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment. Dome Button - This button is located below the TV screen. NOTE You can set the power indicator light to on or off by selecting General in the main menus. -
Page 4: Ezmanager
EZMANAGER EZMANAGER • Image shown may differ from your TV. • INTRODUCTION The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions. The default Domain “procentric.local” and IP Server Address are needed to be registered in DNS TV will contact the IP Server using the default Domain “procentric.local” via IP on server search page. EZ-MANAGER WIZARD - If you are using Pro:Centric, this setup wizard till help you easily set up the TV. -
Page 5: Language & Country Selection
EZMANAGER LANGUAGE & COUNTRY SELECTION - Please select the Language, Country and Time Zone. -
Page 6: Automatically For Setup
EZMANAGER Automatically for Setup From the TV Configuration Options screen, you can choose how to proceed with the configuration of this TV. Whether you will configure the TV for Pro:Centric operation via the wizard or use a USB memory device to configure the TV, you may first wish to set the Room Number on the TV. - If you intend to set Room Number as part of the TV configuration, use the Room Number option to assign the Room # for this TV before you continue with additional configuration. - Page 7 EZMANAGER This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data channel, select the ‘NEXT’ .
- Page 8 EZMANAGER Downloading the Pro:Centric application files takes few minutes. After the installation is completed, the following screen will be displayed.
-
Page 9: Manually For Setup
EZMANAGER Manually for Setup Select a Label and/or enter the Room Number using the numeric keypad on the remotes or using the virtual keyboard on the TV screen. To continue, move and select ‘NEXT’ . Please select the ‘MANUAL PRO:CENTRIC’ . - Page 10 EZMANAGER Configure the appropriate Pro:Centric settings in the TV. Downloading the Pro:Centric application files takes few minutes.
- Page 11 EZMANAGER After the installation is completed, the following screen will be displayed.
-
Page 12: Usb Lg Smart Install Utility
EZMANAGER USB LG Smart Install Utility Select the ‘USB CONFIGURATION’ →‘TV MANAGER’ . - If you have USB Memory for “LG_DTV” or “lg_dtv” folder, this step shows the USB file list for downloading the items. - Page 13 EZMANAGER Downloading the Pro:Centric application files takes few minutes. After the installation is completed, the following screen will be displayed.
-
Page 14: Installation Menu
The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’ . The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient operation for Hotelier and System Integrators. -
Page 15: Public Display Settings
INSTALLATION MENU PUBLIC DISPLAY SETTINGS button to select the PUBLIC DISPLAY SETTINGS. Use the Use the ‘OK’ button and then button to select Public Display Mode. - When ‘Public Display Mode’ is set to On (Work), all functions of Public Display Mode apply. Public Display Settings Operation - Decide to work all functions of ‘Public Display Mode’... -
Page 16: Volume
IR Operation y Decide whether work the LG remote control or not. - When ‘IR Operation’ is set to 'Normal' , all remote keys are available. - 'Use PWR Only' makes block all remote keys except power key. -
Page 17: Limited Mode
INSTALLATION MENU Limited Mode - Configure TV function’s limitation. When selected to ‘On’ , following sub-menus will be worked by below. Setup Menu - Decide to enter 'Setup’ Menu’ as ‘On’(Enter possible) or ‘Off’(Enter impossible) Channel Change y Decide to change channel or not by setting ‘Program Change' as ‘On’(Change Possible) or ‘Off’(Change Impossible) when present source is TV. - When ‘Channel Change' is set to Off (Change Impossible) »... -
Page 18: Power On Default
INSTALLATION MENU Power On Default - Set the channel to display and Volume Level, etc. when turn on power in AC Power On or Stand-by status. - Set to On(Work) or Off(Do Not Work). - When ‘Power On Default’ is set to Off, it is not applied to the subordinate Channel, Volume, A/V Setting menu. -
Page 19: Network
INSTALLATION MENU NETWORK Use the button to select the NETWORK. MAC Address - Displays the MAC address (not customizable). Network Setting One-click network connection - Connects easily to a wired/wireless network. - Network Connection to connect to an available network automatically. Follow the prompts on the TV. To connect to a network through Set Expert - For use in special circumstances such as in offices (in cases where a static IP is used). -
Page 20: Ip Stream Control
INSTALLATION MENU IP Stream Control Audio PTS Offset - Controlling output stream timing of audio. - You can set the '-500~500' (Change step is -10 or +10) Video PTS Offset - Controlling output stream timing of video. - You can set the '-500~500' (Change step is -10 or +10) IGMP - You can set IGMP version. -
Page 21: P:c Ip Setting
INSTALLATION MENU P:C IP Setting - Server Address is set to IP Address (IP Address) Set IPv4 address in 4 octets. (Port Number) Sets the actual port or number where the Pro:Centric server is running. - Server Address is set to Domain Name (Domain Name) Sets the domain name where the Pro:Centric server is running. - Page 22 INSTALLATION MENU Number of RCU - It is a mode to set Number of RCU. Number of RCU value range 1~9. (When ‘Select RCU’ is set to ‘Enable’) Number of RCU value range 0. (When ‘Select RCU’ is set to ‘Disable’) RCU(Remote Control Unit) : It is special RCU that operates only setted number of RCU in TV.
- Page 23 INSTALLATION MENU Signal Signal requirements RX RS232 Standard RS232 specification TX RS232 Standard RS232 specification IR from TV Power ground 6, 8 Not connected Male connector on box, viewed +5VDC 10%, max 100mV ripple towards connector. 1.5 A +12VDC 10%, max 100mV ripple DTV Channel Update - It is a mode to set whether to update DTV Channel automatically or not.
-
Page 24: External Speaker
INSTALLATION MENU InStant On - Set to ‘Instant On Mute Mode’ or ‘Instant On Reboot mode’ to enable the Instant ON feature. The Instant ON feature allows the TV to turn ON when AC power is applied, but with video and audio muted (Muted ON). The TV retains its ON status while appearing to be OFF. Pressing the POWER button toggles Off/On the video and audio mutes, so that the TV appears to turn ON instantly. -
Page 25: Hcec Setup
- You will have 3 modes to choose [Default], [HCEC] and [TVLink-CEC]. - If [Default] is selected, you can use SIMPLINK which is provided in LG TV. Also you can enable and disable SIMPLINK through SIMPLINK MENU. - If [HCEC] is selected, you can use TVLink-HCEC Protocol. For more detailed information, please refer to TVLink-HCEC Protocol document) - If [TVLink-CEC] is selected, TV will not directly work for key input except for power key. -
Page 26: Clock Setup
INSTALLATION MENU Clock Setup Clock Source - You can select ‘Off’ , ‘Pro:Centric’ , ‘TV’ , ‘NTP’ , ‘Admin’ by pressing button. - NTP : Clock is synchronized using Network Time Protocol. It's only enabled when network cable is connected. - Admin : It's automatically set to Admin when clock is updated by commercial protocols like TVLink-HCEC, TVLink-Interactive, or HCAP API. -
Page 27: Media Share
TV. - Supported device : Mobile device based on Android (higher than v4.4 Kitkat) / iOS » support the lower than v4.4 (Kitkat) on the LG mobile device based on Android - Supported version : Higher than Bluetooth 3.0 DIAL - With this DIAL service, you can launch the target app at Smart Home Launcher bar without select the target app by remote controller. -
Page 28: Softap
INSTALLATION MENU SoftAP - If you want to use SoftAp menu on MEDIA SHARE menu, you must select ‘On’ in this item. A SoftAP is a function of TV which is used like Access Point. Use Default - If you want to use default password(this password was generated randomly), you must select ‘Enable’ in this item. Security Key - When guests want to use TV’s SoftAP function, they need this password. -
Page 29: Tv Manager
INSTALLATION MENU TV MANAGER USB Download Menu * USB Cloning : An Installer can quickly set up and clone multiple TV sets at a property. These cloned TVs will all have the same Master TV Setup: Public Display Mode Installation Menu settings, User A/V settings and the Channel Map. This newer procedure significantly decreases the installa- tion time that would be necessary if the standard RS-232C method were used instead. - Page 30 INSTALLATION MENU Ez Download - Ez Download is a function that enables users to download the desired items all at once, such as EPK (software update file), TLL, Logo Image, Background Images, Micom. Splash images and EPK files should be copied into the folder named LG_DTV on the USB. - TLL files should be copied to the root folder of the USB.
- Page 31 INSTALLATION MENU Logo Image Download - If there are more than two USB Memory Device, It is possible to select the USB. - The download sequence is Logo Image Download -> Select Image -> UPDATE. NOTE Splash Image update function supports only JEPG,BMP format file of less than 8 MB filesize. We recommend you that splash image resolution match the TV`s panel resolution.
- Page 32 INSTALLATION MENU Insert Background Image(s) - Images should be copied to LG_DTV of the USB. - The download sequence is Insert Background Image(s) -> Select Images -> UPDATE. NOTE Maximum number of images that you can update at once are 12. If you updates the images, original images will be removed.
- Page 33 INSTALLATION MENU Update TV Software - This feature updates TV through the EPK file in USB. The target file is located in LG_DTV folder. - If there are more than two USB memory Device, It is possible to select the USB. - The download sequence is USB →...
- Page 34 INSTALLATION MENU Import Clone File - Once the internal TV data and its channel map information is written to the USB memory card, the user can start “Import Clone File” process with the data file generated and stored in USB memory card. As previously warned in “Export Clone File” process, the user should not turn TV off nor unplug the USB memory card.
-
Page 35: Diagnostics Menu
INSTALLATION MENU Diagnostics Menu This diagnostic function provides current status information of the TV in XML file format using a USB device. If the user sets a signal standard level, SignalTrace checks the signal strength status of the digital channel that the user tuned to. It checks and records good and bad channel signals, and then provides the signal information to a USB storage device in XML file format.