Specifications - Orion SKYQUEST XT10 CLASSIC Instruction Manual

rors, the better. Small specks of dust or flecks of paint have
virtually no effect on the visual performance of the telescope.
The large primary mirror and the elliptical secondary mirror of
your telescope are front-surface aluminized and overcoated
with hard silicon dioxide, which prevents the aluminum from
oxidizing. These coatings normally last through many years of
use before requiring re-coating, which is easily done.
To clean the secondary mirror, it must be removed from the
telescope. Do this by holding the secondary mirror holder sta-
tionary with your fingers (don't touch the mirror itself) while
unthreading the Phillips head screw in the center hub of the
4-vaned spider. Completely unthread the screw from the hold-
er, and the holder will come loose in your fingers. Be careful
not to lose the spring on the Phillips head screw.
Handle the mirror and its holder carefully. You do not need to
remove the secondary mirror from its holder for cleaning. To
clean the secondary mirror, follow the procedure described
below for cleaning the primary mirror.
To clean the primary mirror, carefully remove the mirror cell
from the telescope. To do this, you must remove the screws
that connect the entire mirror cell to the steel tube. These
screws are located on the outer edge of the mirror cell.
Now, remove the mirror from the mirror cell by removing the
three mirror clips that secure the mirror in its cell. Use a Phillips
head screwdriver to unthread the mirror clip anchor screws.
Next, hold the mirror by its edge, and remove it from the mir-
ror cell. Be careful not to touch the aluminized surface of the
mirror with your fingers. Set the mirror on a clean, soft towel.
Fill a clean sink, free of abrasive cleanser, with room-temper-
ature water, a few drops of liquid dishwashing detergent, and
if possible, a capful of rubbing alcohol. Submerge the mirror
(aluminized face up) in the water and let it soak for several
minutes (or hours if it is a very dirty mirror). Wipe the mirror
underwater with clean cotton balls, using extremely light pres-
sure and stroking in straight lines across the surface. Use one
ball for each wipe across the mirror. Then rinse the mirror
under a stream of lukewarm water. Any particles on the sur-
face can be swabbed gently with a series of clean cotton balls,
each used just one time. Dry the mirror in a stream of air (a
"blower bulb" works great), or remove any stray drops of water
with the corner of a paper towel. Water will run off a clean sur-
face. Dry the bottom and the edges with a towel (not the mirror
surface!). Cover the mirror surface with tissue, and leave the
entire assembly in a warm area until it is completely dry before
reassembling the telescope.
16

7. specifications

skyQuest Xt 6"
Primary mirror
focal length:
Primary mirror diameter:
Focal Ratio:
Focuser:
Optical tube material:
Eyepiece:
Magnification with
supplied eyepiece:
Reflex Sight:
Reflex Sight Bracket:
Mirror coatings:
Minor axis of
secondary mirror:
Optical tube weight:
Base weight:
Tube length:
Tube outer diameter:
skyQuest Xt 8"
Primary mirror
focal length:
Primary mirror diameter:
Focal Ratio:
Focuser:
Optical tube material:
Eyepiece:
Magnification with
supplied eyepiece:
Reflex Sight:
Reflex Sight Bracket:
Mirror coatings:
Minor axis of
secondary mirror:
Optical tube weight:
Base weight:
Tube length:
Tube outer diameter:
1200mm, standard optical glass
150mm
f/8.0
Rack and pinion, accepts 1.25"
eyepieces
Rolled steel
25mm Sirius Plössl, fully coated
with multi-coatings, 1.25" barrel
diameter
48x
EZ Finder II
Plastic bracket with dovetail base
Aluminum with SiO 2 overcoat
34.5mm
13.5 lbs.
20.9 lbs.
45.5"
7.25"
1200mm, standard optical glass
203mm
f/5.9
Crayford, accepts 2" eyepieces
and 1.25" eyepieces with adapter
Rolled steel
25mm Sirius Plössl, fully coated
with multi-coatings, 1.25" barrel
diameter
48x
EZ Finder II
Plastic bracket with dovetail base
Aluminum with SiO overcoat
2
47.0mm
20.3 lbs.
20.7 lbs.
46.5"
9.25"