Technical Data; Approved Bar And Chain Combinations - Makita DCS431 Owner's And Safety Manual

Technical data

Stroke volume
Bore
Stroke
Max. power at speed
Max. torque at speed
Idling speed
Coupling speed
Sound Pressure Level at the operator's ear
at full load according to ANSI B 175.1 db(A)
Sound Pressure Level at the bystander's position
(50ft/15 m distance) according to ANSI B 175.1 db(A)
Carburetor (for CANADA)
Carburetor (for USA)
Ignition system
Spark plug
Electrode gap
or spark plug
Fuel consumption at max. load
Specific consumption at max. load
Fuel tank capacity
Chain oil tank capacity
Mixture ratio (fuel/two-stroke oil)
Chain brake
Weight
(fuel tank empty, without chain and guide bar)
1)
DCS5200 = Walbro WT 465 / DCS5200i = TILLOTSON HU 116
"Low-kickback saw chain is a chain which has met the kickback performance requirements of ANSI B 175.1-1991
(American National Standard for Power Tools-Gasoline-Powered Chain Saws-Safety Requirements) when tested on the
representative sample of chain saws below 3.8 c.i.d. specifed in ANSI B 175.1-1991". The approved bar and chain
combinations are low kickback chains according to ANSI B 175.1-1991 and also meet the kickback requirements of
CSA Z62.3-96 for chains saws below 80 cm
Do not use other replacement bars and chains unless they have been designated as meeting the ANSI B 175.1-1991
(for USA) and CSA Z62.3-96 (for Canada) kickback performance requirements on that specific powerhead, or has
been designated as "low kickback" saw chain in accordance with the ANSI B 175.1-1991 (for USA) and CSA
Z62.3-96 (for Canada) standard.
Guide bar and saw chain combinations meeting kick-
back requirements of ANSI B 175.1-1991 for the use
in the
Models DCS430, DCS431
GUIDE BAR
length pitch
15" (38 cm) .325"
16" (40 cm) .325"
18" (45 cm) .325"
Drive link gauge: .058", Chain sprocket: 8 teeth
Models DCS520, DCS520i, DCS540, DCS5200, DCS5200i
GUIDE BAR
length pitch
15" (38 cm) .325"
16" (40 cm) .325"
18" (45 cm) .325"
Drive link gauge: .058", Chain sprocket: 8 teeth
18" (45 cm) 3/8"
21" (53 cm) 3/8"
Drive link gauge: .050", Chain sprocket: 7 teeth
18
DCS430 / 431
cu. in 2.7 (43 cm
inch 1.57 (40 mm)
inch 1.34 (34 mm)
kW / rpm 2.0 / 9,000
Nm / rpm 2.4 / 6,000
rpm
rpm
Type Walbro WT 465
Type Walbro WT 465
Type electronic
Type BOSCH WSR 6F
inch
Type NGK BPMR 7A
kg/h
g/kWh
oz
oz

Approved bar and chain combinations

3
.
USA
SAW CHAIN
part no. part no.
445 038 631 523 085 664
445 040 631 523 085 666
445 045 631 523 085 672
SAW CHAIN
part no. part no.
445 038 631 523 085 664
445 040 631 523 085 666
445 045 631 523 085 672
443 045 661 523 102 664
443 053 661 523 102 672
DCS520 / 520i
3 ) 3.2 (52 cm
1.73 (44 mm)
1.34 (34 mm)
2.4 / 9,000
2.9 / 6,000
2,500 2,500
3,600 3,600
102 102
75 75
TILLOTSON HU 116
TILLOTSON HU 116
electronic
BOSCH WSR 6F
.020 .020
NGK BPMR 7A
0.90 1.08
450 450
18.6 18.6
9.3 9.3
see chapter "Fuel"
Engages manually or in case of kickback.
10 lbs 10 lbs
WARNING
Guide bar and saw chain combinations meeting kick-
back requirements of CSA Z62.3-96 for the use in
Models DCS430, 431, 520, 520i, 540 and DCS5200, 5200i
GUIDE BAR
length
15" (38 cm)
16" (40 cm)
18" (45 cm)
Drive link gauge: .058", Chain sprocket: 8 teeth
15" (38 cm)
18" (45 cm)
21" (53 cm)
Drive link gauge: .058", Chain sprocket: 7 teeth
DCS540
3 ) 3.3 (54 cm 3 )
1.77 (45 mm)
1.34 (34 mm)
2.2 / 9,000
3.0 / 6,000
2,500
3,600
102
75
Walbro WT 465
Walbro WT 465
electronic
BOSCH WSR 6F
.020
NGK BPMR 7A
1.30
590
18.6
9.3
10 lbs 2 oz
CANADA
pitch part no.
.325" 445 038 631
.325" 445 040 631
.325" 445 045 631
3/8" 443 038 651
3/8" 443 045 651
3/8" 443 053 651
DCS5200 / 5200i
3.2 (52 cm 3 )
1.73 (44 mm)
1.34 (34 mm)
2.7 / 9,000
3.1 / 6,000
2,500
3,600
102
75
1)
1)
electronic
BOSCH WSR 6F
.020
NGK BPMR 7A
1.21
450
18.6
9.3
10 lbs 2 oz
SAW CHAIN
part no.
523 085 664
523 085 666
523 085 672
522 094 656
522 094 664
522 094 672