Korg Triton Studio Parameter Manual page 287

Not enough memory to load
Meaning: When you attempted to load a .SNG file or a stan-
dard MIDI file in Disk mode, there was insuffi-
cient free memory in the sequence memory.
Action: Delete other song data etc. to increase the amount
of free memory.
Not enough memory to open pattern
Meaning: There was insufficient sequencer memory to open
the pattern, so editing is not possible.
Action: Either delete unwanted data such as a song, track,
or pattern, or do not open the pattern.
Not enough multisample memory
Meaning: There is insufficient multisample memory. (The
number of multisamples would exceed the maxi-
mum of 1,000.)
Action: Delete multisamples to increase the amount of
free memory.
Not enough relative parameter memory
Meaning: There is insufficient memory for relative parame-
ters. (The number of samples in the multisamples
would exceed the maximum of 4,000.)
Action: Delete multisamples or indices of multisamples to
increase the amount of free memory.
Not enough sample memory
Meaning: There is insufficient sample memory (for sample
parameters or sample waveform data).
Action: Delete samples to increase the amount of free
memory.
Not enough sample/multisample locations available
Meaning: The data you attempted to load would exceed the
maximum number of multisamples or samples.
Action: In Sampling mode, execute "Delete Multisample"
or "Delete Sample" to free a sufficient number,
and reload the data.
Not enough song locations available
Meaning: When loading a .SNG file with "Append" speci-
fied, you attempted to load more songs than can
be loaded.
Action: In Sequencer mode, execute "Delete Song" to
increase the number of multi's that can be used,
and then load the song again.
Not enough song memory
Meaning: When executing the Sampling mode "Time Slice"
or "Save" commands, the total data for all songs
occupies all of the sequence data memory area, so
that saving is not possible.
Meaning: When sampling to RAM in Sequencer mode, it is
not possible to create track data at the same time.
Action: Increase the amount of free memory, for example
by deleting another song.
276
O
Obey Copyright Rules
Meaning: This will be displayed when you make settings for
S/P DIF Input or mLAN input, when you execute
the Disk mode Make Audio CD page "Write to
CD" command, or when you execute "Destina-
tion" in the Sampling mode Audio CD page "Des-
tination" command. Please read "About
copyright" ( BG p.iii) before you use this data.
Oscillator Mode conflicts (check PROG P1)
Meaning: In Sampling mode when you executed "Convert
MS To Program" with Use Destination Program
Parameters checked, the conversion destination
program "Oscillator Mode" setting did not match.
Action: In Program mode, set the "Oscillator Mode" of the
conversion destination program. If converting a
monaural multisample, select Single. If converting
a stereo multisample, select Double.
P
Pattern conflicts with events
Meaning: It was not possible to execute the Bounce opera-
tion because one of the tracks contained a pattern,
and the same measure of the other track contained
events or a pattern.
Action: Open the pattern.
Pattern exists across destination to-end-of-measure or
source from-measure
Meaning: When moving a measure, the edit operation could
not be executed because a pattern had been put in
the destination end measure or the source start
measure, and had not been opened.
Action: Open the pattern.
Pattern exists in destination or source track
Meaning: A pattern has been placed in the track that you
specified as a destination or source for editing. If
you wish to open the pattern and execute (the
events of the pattern will be copied), press the OK
button. If you wish to execute without opening
the pattern, press the Cancel button.
Pattern used in song
Meaning: When editing, the specified pattern has been
placed in a track. If you wish to execute, press the
OK button. If you decide not to execute, press the
Cancel button.
R
Rear sample is empty
Meaning: When you executed "Link" in the Sampling mode
Sample Edit page, the sample that you specified
as the rear sample is empty.
Action: Specify a sample that contains data as the rear
sample, and execute once again.
Request rejected
Meaning: In the Global mode mLAN Output/Input page, a
request to mLAN was not accepted.
Open pattern ?
Continue ?