Kenwood VR-8060 Instruction Manual page 18

Preparing for surround sound
6 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate Center Speaker setting.
If you selected "LARGE" as the Front Speakers setting,
1 CNTR NORMAL : An average size Center Speaker is
2 CNTR LARGE
3 CNTR OFF
If you selected "NORMAL" as the Front Speakers setting,
1 CNTR NORMAL : An average size Center Speaker is
2 CNTR OFF
7 Press the ∧ ∧ ∧ ∧ ∧ key or # key again to accept the setting.
• The Surround Speaker setting indication "SURR" appears.
8 Use the MULTI CONTROL knob or Multi (%/fi) to select the
appropriate Surround Speaker setting.
If you selected "LARGE" as the Center Speaker setting,
1 SURR NORMAL : Average size Surround Speakers are
2 SURR LARGE
3 SURR OFF
If you selected other than "LARGE" as the Center Speaker
setting,
1 SURR NORMAL : Average size Surround speakers are
2 SURR OFF
• When the setting "SURR OFF" is selected, the procedure skips
to step !.
9 Press the ∧ ∧ ∧ ∧ ∧ key or # keys again to accept the setting.
• The Surround Speaker setting indication "SB" appears.
0 Use the MULTI CONTROL knob or Multi (%/fi) keys to
select appropriate Surround Back Speaker setting.
If you selected "LARGE" as the Surround Speaker setting,
1 SB NORMAL :
2 SB LARGE
:
3 SB OFF
:
SP MUTE OPTICAL 6CH INPUT
AUTO DETECT
A B CLIP
COAXIAL ANALOG
L C SW R
LFE
SL S SB SR
If you selected "NORMAL" as the Surround Speaker setting,
1 SB NORMAL : Average size Surround Back Speaker is
2 SB OFF
: Surround Back Speaker setting mode to
• After setting SB (Surround Back) from OFF to NORMAL, SB/SW
AMP setup display will appear to enable you to re-select either SW
or SB from the Surround Back Speaker or Subwoofer terminal.
! Press the ∧ ∧ ∧ ∧ ∧ key or # key again to accept the setting.
• The Subwoofer remix setting indication "SW RE-MIX" appears.
18
EN
connected to the receiver.
: A large Center Speaker is connected
to the receiver.
: Center Speaker setting mode to the
receiver is OFF.
connected to the receiver.
: Center Speaker setting mode to the
receiver is OFF.
connected to the receiver.
: L a r g e S u r r o u n d S p e a k e r s a r e
connected to the receiver.
: Surround Speaker setting mode to
the receiver is OFF.
connected to the receiver.
: Surround speaker setting mode to
the receiver is OFF.
Average size Surround Back Speaker is
connected to the receiver.
Large Surround Back Speaker is con-
nected to the receiver.
Surround Back Speaker setting mode
to the receiver is OFF.
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6
THX
ACTIVE EQ. MATRIX
Surround EX
96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
connected to the receiver.
the receiver is OFF.
@ Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate Subwoofer re-mix setting.
1 SW RE-MIX ON : Subwoofer re-mix setting mode to
2 SW RE-MIX OFF : Subwoofer re-mix setting mode to
• If Subwoofer is turned off, Subwoofer re-mix setting is not visible.
# Press the SETUP key again to return to the main setup
displays.
5
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
• The receiver enters the speaker volume level adjustment mode.
• Indicators appear only for the channels of the speakers selected
in step 4.
1 Press the ∧ ∧ ∧ ∧ ∧ / ∨ ∨ ∨ ∨ ∨ keys or @/#keys to select TEST TONE.
2 Press the SETUP key for the following displays:
1 T.TONE AUTO
2 T.TONE MANUAL
3 The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or Multi (%/fi) keys.
Press the SETUP key again to begin TEST TONE.
Use the MULTI CONTROL knob or Multi (%/fi) keys to adjust
the volume level of the test tone output from the speaker
channel to be adjusted.
For AUTO selection, the first test tone is heard from the front left
speaker for 2.5 seconds. The next test tone is heard from the
speakers in the following sequence for 2 seconds each.
LEFT
SUBW
The channel indication blinks while the test tone is being output.
SP
A B
L C SW R
LFE
SL S SB SR
• If you have selected "SB/SW AMP SB", "SBR" and "SBL" are
not appeared but "SB" is appeared on the Display.
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed.
• If the speaker setting selects are OFF, the speaker level
settings are reset.
RDS
For MANUAL selection, press the ∧ ∧ ∧ ∧ ∧ / ∨ ∨ ∨ ∨ ∨ keys or @/# keys
RTY
AUTO
each time to select the speaker channel.
MEMO
STEREO
TUNED
4 Press the SETUP key again.
• The test tone is turned off and return to the main setup displays.
6
Input the distance to the speakers.
• Indicators appear only for the channels of the speakers selected
in step 4.
1 Press the ∧ ∧ ∧ ∧ ∧ / ∨ ∨ ∨ ∨ ∨ keys or @/# keys to select the SP DISTANCE on
setup displays and press the SETUP key again.
2 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to Front Left Speaker (L)
Distance to Center Speaker (C)
Distance to Front Right Speaker (R)
the receiver is ON.
the receiver is OFF.
CNTR RIGHT
SL SBL
CINEMA EQ. DTS. DOLBY DIGITAL
MUTE OPTICAL 6CH INPUT
AUTO DETECT
ACTIVE EQ. MATRIX
CLIP
COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
SR
SBR
STEREO NEO:6 RDS
THX
RTY
Surround EX
LOUDNESS CSII
AUTO
MEMO
STEREO
TUNED
º