Assembling The Blades - Hunter Ceiling Fans Installation And Operation Manual

For Flush Mounting: The arrows on the low profile washer and
on the ceiling plate should be pointing in the same direction
and should be pointing towards the tab hole on the canopy.
2. Hook the tab hole over the tab on the ceiling plate as shown in
Figure 19.
3. Raise the canopy, be sure the holes in the canopy and the ceil-
ing plate are aligned, and loosely assemble the canopy screws
one at a time. When all three screws are assembled, securely
tighten all three canopy screws. Refer to Figure 19.
F F F F F i i i i i g g g g g ur ur ur ur ure 19 - I e 19 - In n n n n s s s s s t t t t t a a a a a llin e 19 - I e 19 - I
e 19 - I
installing the canopy trim ring
1. To easily install the canopy trim ring, locate the two tabs on
the canopy trim ring. See Figure 20.
F F F F F i i i i i g g g g g ur ur ur ur ure 20 - C e 20 - Ca a a a a n n n n n o o o o o p p p p p y t e 20 - C e 20 - C e 20 - C
2. Take both hands and push the canopy trim ring up to the top
of the canopy. See Figure 20.
3. The canopy trim ring will snap and lock into place on the
canopy.
removing the canopy trim ring
1. Locate the tab indicators, small bumps on top of tabs. Refer to
Figure 21.
2. To remove the canopy trim ring, press firmly on opposite sides
of the ring towards the canopy as shown in Figure 21. The tabs
will flex out releasing the trim ring from the canopy.
F F F F F i i i i i g g g g g ur ur ur ur ure 21 - R e 21 - R e 21 - R e 21 - Re e e e e m m m m m o o o o o v v v v v in in in in ing t
e 21 - R
© 2003 Hunter Fan Company
llin llin g t g th h h h h e c g t e c e ca a a a a n n n n n o o o o o p p p p p y y y y y e c
lling t llin g t e c
y t y tr r r r r im r y t y t im r im rin in in in ing g g g g im r im r
g th h h h h e c g t g t e c e ca a a a a n n n n n o o o o o p p p p p y t e c y t y t y t y tr r r r r im r im rin in in in ing g g g g im r im r
g t e c im r

assembling the blades

Hunter fans use several styles of fan blade irons (brackets that hold
the blade to the fan).
1. Your fan may include blade grommets. If your fan has grom-
mets, insert them by hand into the holes on the blades as shown
in Figure 22.
F F F F F i i i i i g g g g g ur ur ur ur ure 22 - I e 22 - In n n n n s s s s s e e e e e r r r r r t t t t t in in in in ing t e 22 - I e 22 - I g t g t g t g th h h h h e g e g e g e gr r r r r o o o o o mm
e 22 - I e g
2. Attach each blade to blade iron using three blade assembly
screws as shown in Figure 23. Some fans feature a decorative
medallion as well as a blade iron. Insert the assembly screws
into the blade iron, through the blade and into the medallion,
with the blade sandwiched between the blade iron and me-
dallion as shown in Figure 24.
F F F F F i i i i i g g g g g ur ur ur ur ure 23 - A e 23 - At t t t t t t t t t a a a a a c c c c c h h h h h in in in in ing t e 23 - A e 23 - A g th h h h h e b g t g t
e 23 - A g t
mme e e e e t t t t t s in mm mm s in s in s int t t t t o t o th h h h h e f e f e f e f e fa a a a a n b o t o t n b n bl l l l l a a a a a d d d d d e e e e e s s s s s n b
mm s in o t n b
e bl l l l l a a a a a d d d d d e t e b e b e t e t e t o th h h h h e b o t o t e b e bl l l l l a a a a a d d d d d e ir e b e ir e iro o o o o n n n n n e ir
e b e to t o t e b e ir
41847-01 04/21/2003
7 7 7 7 7