Page 3
Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
For proper alignment use slotted holes directly across from each other. If you are installing the fan on an ANGLED ceiling, be sure to orient the hanger bracket as shown in Illustration 2-3 (left or right view).
3-1 – 3-3. For low profile mounting (ceilings less than 8 feet high), go to steps 3-6 – 3-9 on the next page. 3-1. To assemble fan to hang down from a flat or angled ceiling, place the canopy and canopy trim ring around the adapter so that they rest on the fan assembly.
Page 7
3-9. Align the screw holes in the washer with the holes in the adapter. Assemble securely with three #8-32 x 3/4” screws. 3-10. Raise the fan and place the hook on the hanger bracket through the round hole in the rim of the canopy.
4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 45049-01 • 07/13/09 • Hunter Fan Company 4 •Wiring the Fan (grounding) from the...
Should you need to remove the canopy trim ring, follow these steps: 1. Twist canopy trim ring counter clockwise until it releases from canopy. Step 5-5 45049-01 • 07/13/09 • Hunter Fan Company Steps 5-1 – 5-2 Canopy Step 5-4 Canopy Screw...
Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Attach each blade to a blade iron using three blade assembly screws.
CAUTION: Make sure the upper switch housing is securely attached to the switch housing mounting plate. Failure to properly attach and tighten all three assembly screws could result in the switch housing fixture falling. 45049-01 • 07/13/09 • Hunter Fan Company Steps 7-1 – 7-4 Housing Assembly...
Page 12
7-10. Remove the wire connectors from the two wires in the switch housing labeled “Connect Light Here” or “For Light Use. ” Steps 7-8 – 7-9 45049-01 • 07/13/09 • Hunter Fan Company Lower Switch Housing Threaded Rod...
Page 13
Secure all wire connections using wire connectors. 7-12. To attach the lower switch housing assembly to the fan, partially install two housing assembly screws into the upper switch housing.
190 Watts. Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation. 45049-01 • 07/13/09 • Hunter Fan Company 8 •Glass Installation Light Bulbs (B10 Candelabra Base 40 Watt...
Page 15
9 • Operating and Cleaning Your Ceiling Fan 9-1. Turn on electrical power to the fan. 9-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low, and Off. • Pull the chain slowly to change settings.
Page 16
Consider using Soundolier’s® optional accessories, which include Wireless Subwoofers and Duo™ Lamps. Optional accessories can be purchased through Authorized Hunter Dealers. For quiet and optimum performance of your Hunter fan, use only 3.5 mm Stereo Cable Installation Hunter speed controls. Speaker Wire Installation 45049-01 •...
CAUTION: The remote control device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment. Operation is subject to the following two conditions: 1.
VOLUME of the speaker. Press to decrease the VOLUME of the speaker. Pressing the will switch the surround sound function between: LED Indicators 45049-01 • 07/13/09 • Hunter Fan Company Right Channel Left Channel Mixed Channel LED Indicators...
12-2. To change the channel on the fan press the remote. 12-3 The green/red LED indicators on the bottom of the fan display the channel the fan is tuned to. Green LEDs indicate a good signal and red LEDs indicate no signal.
2. Check to see if the blade is cracked. If so, replace all the blades. Problem: Excessive wobbling. 1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan. 2. Tighten all blade iron screws.