Advertisement
Table of Contents
- 1 Table of Contents
- 2 Getting Ready
- 3 Installing the Ceiling Plate
- 4 Setting the Remote Transmitter and Receiver
- 5 Wiring the Fan
- 6 Installing the Canopy and Canopy Trim
- 7 Assembling the Blades
- 8 Completing Your Installation with a Bowl Light Fixture
- 9 Operating the Remote Control and Mounting the Holder
- 10 Troubleshooting
- Download this manual
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Form# 42649-01
20090813
©2009 Hunter Fan Co.
Type 3 Models
Type 3 Models
Type 3 Models
Owner's Guide and Installation Manual
Advertisement
Table of Contents
Related Manuals for Hunter 42649-01
Summary of Contents for Hunter 42649-01
- Page 1 For reference, also attach your receipt or a copy of your receipt to the manual. __________________________________________ Model Name __________________________________________ Model No. __________________________________________ Date Purchased __________________________________________ Where Purchased Form# 42649-01 20090813 ©2009 Hunter Fan Co. Type 3 Models Type 3 Models Type 3 Models Owner’s Guide and Installation Manual...
-
Page 2: Table Of Contents
9 • Operating and Cleaning Your Ceiling Fan ....... 13 10 •... - Page 3 Understanding Mounting and Installer’ s Choice® Hunter’s patented 2-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of two ways, depending on ceiling height and your preference: Standard or Angled mounting. The steps in this manual include instructions for both Installer’s Choice mounting methods.
-
Page 4: Getting Ready
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •... -
Page 5: Installing The Ceiling Plate
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. 42649-01 • 08/13/09 • Hunter Fan Company For Angled Ceilings: Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak. -
Page 6: Setting The Remote Transmitter And Receiver
CAUTION: The remote control device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment. Operation is subject to the following two conditions: 1. -
Page 7: Wiring The Fan
“LIGHT LIVE OUT”). • Connect the red wire (ungrounded) from the fan to the red wire (ungrounded) from the receiver. 42649-01 • 08/13/09 • Hunter Fan Company 4 • Wiring the Fan Step 4-7 A • Ground/Green Step 4-6 B •... - Page 8 4-9. Turn the splices upward and push them carefully back through 4-10. Spread the wires apart, with the grounded wires on one side of 42649-01 • 08/13/09 • Hunter Fan Company the power wires as follows: • Connect the black wire (ungrounded) from the receiver (marked on white tag “AC LIVE IN”) to the black wire...
-
Page 9: Installing The Canopy And Canopy Trim
Note: Your fan may have multiple tabs and grooves that must be aligned. 5-2. Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate. WARNING: The slots in the canopy must remain engaged while swinging the canopy for alignment. -
Page 10: Assembling The Blades
6 • Assembling the Blades 6-1. Insert blade through housing before installing grommets in each blade. 6-2. Attach each blade to the fan using two blade assembly screws. 42649-01 • 08/13/09 • Hunter Fan Company Grommet Blade Assembly Screw... -
Page 11: Completing Your Installation With A Bowl Light Fixture
190 Watts. Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation. 42649-01 • 08/13/09 • Hunter Fan Company Steps 7-1 - 7-3 Steps 7-4 - 7-5... -
Page 12: Operating The Remote Control And Mounting The Holder
8-1. The remote transmitter has individual buttons for turning the fan off and on and controlling the light and fan speed. 8-2. For best operation, start the fan by pressing high, then select your desired speed. 8-3. The light button turns the light on to full brightness. Push the light button again to turn off the light. - Page 13 9-5. In cold weather, use upward air flow pattern 42649-01 • 08/13/09 • Hunter Fan Company Restore power at the main electrical panel and turn on the wall switch. The light kit should turn ON. Note: To turn on the light without the remote, turn off the wall switch for 5 seconds, then back on.
- Page 14 7% on energy costs. So, you can cut back on expensive air conditioning...and save up to 40%* on cooling. In winter, your Hunter fan recirculates warm air and saves up to 10%* on heating bills.
-
Page 15: Troubleshooting
Problem: If the light on this fan shuts off suddenly. 1. Turn the power to the fan off at the wall switch. Wait 30 seconds, then resume power to the fan. 42649-01 • 08/13/09 • Hunter Fan Company 10 •...