• READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION. SAVE THESE INSTRUCTIONS. • Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to these instructions, and use only the hardware supplied.
Page 3
Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer 42408-01 • 08/10/09 • Hunter Fan Company Ceiling Plate Step 2-2 Steps 2-3 – 2-5...
Page 6
3-4. Align the holes in the washer with the holes in the adapter. Assemble securely with three #8-32 x 3/4” screws. 3-5. Raise the fan and align the slots in the canopy with the tabs on the ceiling plate. Go to 4 • Wiring the Fan.
Page 7
4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 42408-01 • 08/10/09 • Hunter Fan Company...
Step 5-1 Groove Step 5-2 Step 5-3 42408-01 • 08/10/09 • Hunter Fan Company 5 • Installing the Canopy 5-1. Rotate the hanger ball so the tab in the canopy is secure in the groove in the hanger ball. WARNING: Failure to complete this step could cause fan to fall.
Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Attach each blade to a blade iron using three blade assembly screws.
7 • Completing Your Installation With or Without a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button. This feature gives you the option of installing the fan with OR without the included light fixture.
Page 11
190 Watts. Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation. 42408-01 • 08/10/09 • Hunter Fan Company Steps 7-6 – 7-7 Lower Switch Housing...
Page 12
(You may find the plastic breakaway connector on the end of the extra chain.) 7-10. Thread the fan pull chain through the hole in the metal disk. Then, thread the fan pull chain through the hole in the center of the glass bowl.
Page 13
7-22. Once you have uninstalled the light fixture, continue with step 7-6. Male Dummy Terminal Female Dummy Terminal 42408-01 • 08/10/09 • Hunter Fan Company Lower Switch Threaded Rod Steps 7-17 – 7-19 Plug Button Housing Step 7-21...
8 • Operating and Cleaning Your Ceiling Fan 8-1. Turn on electrical power to the fan. 8-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings.
1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan. 2. Tighten all blade iron screws. 3. Turn power off, support fan very carefully, and check that the hanger ball is properly seated. Problem: Lights dim when turned on or do not turn on 1.