Related Manuals for Global Machinery Company POL1450
Summary of Contents for Global Machinery Company POL1450
- Page 1 I N S T R U C T I O N M A N UA L 1450W 7” Grinder/Sander/Polisher • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris POL1450 030901 Ed8 DR...
-
Page 2: Table Of Contents
Additional safety rules for sanders Additional safety rules for angle grinders Additional safety rules for polishers Accessories Unpacking Know your product Setting up Operation in grinder mode Operation in sander mode Operation in polisher mode Replacing the rubber disc Maintenance Cleaning General inspection... -
Page 3: Introduction
Dear Customer If you require any help with your product, whether it is a Warranty claim, spare part or user information, please phone our Help Line for an immediate response. Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand. -
Page 4: Safety Instructions
Safety instructions The tool must be used only for the prescribed purpose. Any uses other than those mentioned in this manual will be considered a case of misuse. The user and not the manufacturer shall be liable for any damage or injury resulting from such cases of misuse. -
Page 5: Additional Safety Rules For Sanders
9. Connect dust extraction equipment. provided for the connection of dust extraction and collection facilities, ensure that these are connected and properly used. 10. Do not abuse the power cord. disconnect the tool from the power point. Keep the cord away from heat, oil and sharp edges. 11. -
Page 6: Additional Safety Rules For Angle Grinders
Always switch off before you put the sander down. • Do not force the sander; let the tool do the work at a reasonable speed. Overloading will occur if too much pressure is applied and the motor slows resulting in inefficient sanding and possible damage to the sander motor. -
Page 7: Additional Safety Rules For Polishers
Wear goggles Wear hearing protection Wear a breathing mask Accessories The GMC POL1450 Grinder/Sander/Polisher is supplied with the following accessories as standard: • Side handle • Metal grinding disc •... -
Page 8: Know Your Product
7. On/Off switch 8. Lock-off button 9. Multi-position front handle 10. Rubber disc 11. Polishing sponge 12. Polishing bonnet 13. Sanding disc Sander 14. Grinding disc 15. Disc guard 16. Inner flange 17. Outer flange Disc assembly Polisher Grinder Depressed disc (thicker than 5mm) -
Page 9: Setting Up
(6) (left side, right side or at the top) to suit the task on hand. Variable Speed The POL1450 is fitted with a variable speed dial (3) that allows you to adjust the speed to suit the application and material. - Page 10 9. To tighten, press and hold the spindle lock button (2) and using the pin wrench tighten the outer flange. 10. Turn the new disc by hand, ensuring that it is tight in the flanges and that it rotates fully and does not wobble unduly.
-
Page 11: Operation In Sander Mode
Fitting the Sandpaper Switch off the tool and disconnect it from the power supply. 1. The GMC grinder/sander/polisher is fitted with a hook & loop base allowing easy changing of accessories. Ensure there are no debris left in the hooks & loops of the disc before fitting accessories. -
Page 12: Operation In Polisher Mode
Do not use any type of abrasive cleanser as it may damage or scratch the surface. Fitting the bonnets 1. Your GMC grinder/sander/polisher comes with a polishing bonnet. The polishing bonnet is used for buffing and finishing the surface. 2. To fit the polishing sponge, press and hold the spindle... -
Page 13: Replacing The Rubber Disc
5. Run the grinder/sander/polisher at no load for at least one minute to ensure the new disc is in good condition. Make sure you are wearing all the safety gear and that you face the polisher away from you. - Page 16 Carefully read the entire Instruction Manual Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: •...