Table of Contents
Advertisement
G
Installation manual
VNRD150ECP
Read this manual carefully before using the product and keep it in a safe place
for reference.
This product was constructed up to standard and in compliance with regulations
relating to electrical equipment and must be installed by technically qualified
personnel.
The manufacturer assumes no responsibility for damage to persons or property
resulting from failure to observe the regulations contained in this booklet.
PRECAUTIONS FOR INSTALLATION, USE AND MAINTENANCE
• T he device should not be used for applications other than those specified in this manual.
• A fter removing the product from its packaging, verify its condition. In case of doubt, contact a qualified technician. Do not leave
packaging within the reach of small children or people with disabilities.
• D o not touch the appliance with wet or damp hands/feet.
• T his appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
• D o not use the product in the presence of inflammable vapours, such as alcohol, insecticides, gasoline, etc.
• I f any abnormalities in operation are detected, disconnect the device from the mains supply and contact a qualified technician
immediately. Use original spare parts only for repairs.
• T he electrical system to which the device is connected must comply with regulations.
• B efore connecting the product to the power supply or the power outlet, ensure that:
- the data plate (voltage and frequency) correspond to those of the electrical mains
- the electrical power supply/socket is adequate for maximum device power. If not, contact a qualified technician.
• T he device should not be used as an activator for water heaters, stoves, etc., nor should it discharge into hot air/fume vent ducts
deriving from any type of combustion unit. It must expel air outside via its own special duct.
• O perating temperature: -20°C up to +50°C.
• T he device is designed to extract clean air only, i.e. without grease, soot, chemical or corrosive agents, or flammable or
explosive mixtures.
• D o not leave the device exposed to atmospheric agents (rain, sun, snow, etc.).
• D o not immerse the device or its parts in water or other liquids.
• T urn off the main switch whenever a malfunction is detected or when cleaning.
• F or installation an omnipolar switch should be incorporated in the fixed wiring, in accordance with the wiring regulations, to
provide a full disconnection under overvoltage category III conditions (contact opening distance equal to or greater than 3mm).
• I f the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.
• D o not obstruct the fan or exhaust grille to ensure optimum air passage.
• E nsure adequate air return/discharge into/from the room in compliance with existing regulations in order to ensure proper
device operation.
• I f the environment in which the product is installed also houses a fuel-operating device (water heater, methane stove etc., that
is not a "sealed chamber" type), it is essential to ensure adequate air intake, to ensure good combustion and proper equipment
operation.
INTRODUCTION
VNRD150ECP is a single alternate flow decentralized (single point) residential heat recovery unit, also called «push&pull» unit,
designed to ensure adequate ventilation in enclosed environments without energy losses.
It is recommended that two units are installed in a pair: when one unit is pulling, the other is pushing.
The pair of units can be installed in the same room or in different rooms (i.e. living-room and bedroom). The unit is suitable for
installation on an outside wall.
The unit should operate continuously, and only stopped for maintenance or service.
When heat exchange is not useful (for example in mid-seasons when indoor and outdoor temperatures are similar), or when
heat exchange is not recommended (for example with the option "summer free cooling"), it is recommended to set the unit in
TECHNICAL SPECIFICATIONS
• D esign front cover (A) removable for cleaning without the use of tools.
• I nner ventilation unit (B) and wall support base (D) made of high quality, impact and UV-resistant ABS, colour RAL 9010.
• I ntegrated multi-colour led (C) to obtain a visual feedback of the unit status.
6
"extract-only" or "intake-only" mode and NOT to switch it off.
Fig.1
Advertisement
Table of Contents
