Denon AVR-1611 Owner's Manual page 53

ENGLISH
Manual Setup
Setting items
Bass Setting Subwoofer Mode : Select low range signals to be reproduced by
Set subwoofer and LFE subwoofer.
signal range playback. • LFE : The low range signal of the channel set to "Small" speaker size is
added to the LFE signal output from the subwoofer.
• LFE+Main : The low range signal of all channels is added to the LFE
signal output from the subwoofer.
• "Subwoofer Mode" can be set when "Speaker Config." – "Subwoofer"
(vpage 49) is set to "Yes".
• Play music or a movie source and select the mode offering the strongest
bass.
• Select "LFE+Main" if you want the bass signals to always be produced
from the subwoofer.
NOTE
If "Front" and "Center" for "Speaker Config." are set to "Large", and
"Subwoofer Mode" is set to "LFE", no sound may be output from the
subwoofers, depending on the input signal or selected surround mode.
LPF for LFE : Set LFE signal playback range.
• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz
Distance Unit : Set the unit of distance.
Set distance from listening • Feet / Meters
position to speakers.
Step : Set the minimum variable width of the distance.
Measure beforehand the
• 1ft / 0.1ft
distance from the listening
• 0.1m / 0.01m
position to each speaker.
FL / FR / C / SW / SL / SR / SBL
z When the "Speaker Config." – "S.Back" setting (vpage 49) is set to
"1sp", "S.Back" is displayed.
• 0.0ft – 60.0ft / 0.00m – 18.00m : Set the distance.
• The speakers that can be selected differ depending on the "Amp Assign"
(vpage 49) and "Speaker Config." (vpage 49) settings.
• Default settings :
FL / FR / C / SW / FHL / FHR : 12.0 ft (3.6 m)
SL / SR / SBL / SBR : 10.0 ft (3.0 m)
• Set the difference in the distance between the speakers to less than 20
ft (6.0 m).
NOTE
Speakers set to "None" in "Speaker Config." (vpage 49) are not displayed.
Default : The "Distance" settings are returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
When you select "Default" and press ENTER, the "Default Setting?"
prompt is displayed. Select either "Yes" or "No", and press ENTER.
50
Remote control operation
buttons
Setting details
z / SBR z / FHL / FHR : Select the speaker.
Move the cursor
(Up/Down/Left/Right)
Setting items
Channel Level Test Tone Start : Output test tone.
Set the volume of the test • FL / C / FR / SR / SBR
tone to be the same when it speaker.
is output from each speaker. z When the "Speaker Config." – "S.Back" setting (vpage 49) is set to
"1sp", "S.Back" is displayed.
• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.
• When o is pressed while the subwoofer volume is set to "–12 dB", the
"Subwoofer" setting switches to "OFF".
• When "Channel Level" is adjusted, the adjusted values are set for all the
surround modes. To adjust the channel level separately for the different
surround modes, use the operation see page 33.
NOTE
• Speakers set to "None" in the "Speaker Config." (vpage 49) settings
are not displayed.
• When a headphones jack is inserted in the PHONES jack of this unit, the
"Channel Level" is not displayed.
Default : The "Channel Level" settings are returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
Crossover Frequency Crossover : Set the crossover frequency.
Set the maximum frequency • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
of the bass signal output
250Hz
from each channel to
Advanced : Specify crossover frequency for each speaker.
the subwoofer. Set the
• Front / Center / Surround / S.Back / Front Height : Select the speaker.
Crossover Frequency to
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
suit the bass reproduction
250Hz : Set the crossover frequency.
capability of the speaker
being used.
• "Crossover Frequency" can be set when the "Bass Setting" –
"Subwoofer Mode" (vpage 50) setting is "LFE+Main", or when you
have a speaker that is set to "Small".
• Always set the crossover frequency to "80Hz". When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
• For speakers set to "Small", sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
• The speakers that can be set when "Advanced" is selected differ
depending on the "Subwoofer Mode" setting (vpage 50).
• When "LFE" is selected, speakers set to "Small" at "Speaker Config."
can be set. If the speakers are set to "Large", "Full Band" is displayed
and the setting cannot be made.
• If set to "LFE+Main", this setting can be made regardless of the
speaker size.
Confirm the setting
Setting details
z / SBL z / SL / FHL / FHR / SW : Select the
Return to previous menu