Download Print this page

Varytec VP-m5 Quick Start Manual

Mobile video bilight

Advertisement

Quick Links

VP-m5 Mobile Video BiLight
Safety instructions
Intended use
This device is intended to be used as a portable video light. Any other use or use
under other operating conditions is considered to be improper and may result in per-
sonal injury or property damage. No liability will be assumed for damages resulting
from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are
not within reach of babies and young children. Choking hazard! Ensure
that children do not detach any small parts from the product. They could
swallow the pieces and choke!
Incorrect handling of lithium batteries can result in injury
In the event of a short circuit, overheating or mechanical damage, lithium
batteries can cause severe injuries. When handled correctly and appropri-
ately lithium batteries pose no risk. Store lithium batteries in a cool, dry
place, ideally in the original packaging. Store lithium batteries away from
heat sources (e.g. radiators or sunlight). Lithium batteries are hermetically
sealed. Never attempt to open a lithium battery. If the battery housing is
damaged small amounts of the electrolyte may leak out. If this should
happen, seal the lithium battery in airtight packaging and wipe up the
traces of electrolyte using absorbent paper towels. You must wear protec-
tive rubber gloves when doing so. Clean your hands and the affected sur-
face thoroughly with cold water. Never attempt to recharge non-re-
chargeable lithium batteries. When charging lithium batteries you must
use a suitable charging device intended for the purpose. Only use powder
extinguishers or other suitable extinguishing agents to extinguish a
burning lithium battery.
Features
• Mini LED video light with variable colour temperature and built-in battery
• Steplessly dimmable
• Easy operation via rotary controls
• With 1/4" internal thread
Operating elements
q
w
Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • info@thomann.de
r
e
Quick start guide
This quick start guide contains important information on the safe operation of the
product. Read and follow the safety advice and instructions given. Retain the quick
start guide for future reference. If you pass the product on to others please include this
quick start guide.
Eye damage caused by high light intensity
Never look directly into the light source.
Extend the operating life of the device by regular breaks and by avoiding
frequent switching on and off. The device is not suitable for continuous
operation.
For technological reasons, the light output of LEDs decreases over their lifetime.
This effect increases with higher operating temperature. You can extend the service
life of the illuminants by providing adequate ventilation and operating the LEDs
with the lowest possible brightness.
Where to use the product
Never use the product
• in conditions of extreme temperature or humidity
• in extremely dusty or dirty areas
• at locations where the unit can become wet
General handling
• To prevent damage, never use force when handling the product.
• Never immerse the product in water. Just wipe it with a clean dry cloth. Do not
use liquid cleaners such as benzene, thinners or flammable cleaning agents.
• USB-C port for charging
• Battery charge level indicator
• Colour temperature steplessly adjustable from 2550 - 6140 K
t
y
ö Battery charge level indicator
# Connection for hot shoe
$ USB-C port
% Brightness control
& On / off switch
' Colour temperature control
EN
DocID: 522506_25.02.2022

Advertisement

loading

Summary of Contents for Varytec VP-m5

  • Page 1 This quick start guide contains important information on the safe operation of the product. Read and follow the safety advice and instructions given. Retain the quick start guide for future reference. If you pass the product on to others please include this VP-m5 Mobile Video BiLight quick start guide. Safety instructions...
  • Page 2 VP-m5 Mobile Video BiLight Using the product 1. First the internal battery must be charged. To do this, connect the device to a 5. Set the desired colour temperature between 2600 - 5700 K with the colour suitable voltage source (not supplied) via its USB-C port e.