Smoke Detector/Fire Shutdown (Fsd); Connecting Discrete Inputs - Carrier 48TC**16 Installation Instructions Manual

J4-1 or J4-4 + 24 VDC Supply Voltage
J4-2 or J4-5 (-) 4 to 20 mA Current Loop Output
to RTU-OPEN
Humidistat: The accessory humidistat provides the RTU
Open insight to the relative humidity in the space. The
humidistat reads the RH level in the space and compares it
to its setpoint to operate a dry contact. The humidistat is a
dedicated input on the configurable input 9 and tells the
RTU Open when the RH level is HIGH or LOW. The
normal condition for humidity is LOW. A normally open
humidistat is the factory default control for the
R
Humidi- - MiZer option.
To wire in the field:
S J5- - 8 = 24 VAC source for dry contact
S J5- - 7 = Signal input
Smoke Detector/Fire Shutdown (FSD) —
On 48TC**16 units equipped with factory- - installed
Smoke Detector(s), the smoke
implements the unit shutdown through its NC contact set
connected to the unit's CTB input. The FSD function is
initiated via the smoke detector's Alarm NO contact set.
The RTU Open controller communicates the smoke
detector's tripped status to the BAS building control. See
Fig. 67, the RTU Open System Control Wiring Diagram.
The Fire Shutdown
MENU Config Inputs input 5, identifies the normally
→ → →
open status of this input when there is no fire alarm.
Connecting Discrete Inputs —
Filter Status: The filter status accessory is a field- - installed
accessory. This accessory detects plugged filters. When
installing this accessory, the unit must be configured for
filter status by setting MENU
8, or 9 to Filter Status and normally open (N/O) or normally
closed (N/C). Input 8 or 9 is recommended for easy of
installation. Refer to Fig. 65 and Fig. 67 or Fig. 68 for wire
terminations at J5.
Fig. 75 - - Duct Relative Humidity Sensor Typical Wiring
detector controller
Switch configuration,
Config Inputs input 3, 5,
→ → →
SPAN
ZERO
4-20 VAC GND 0-5V
mA or or
VDC 0-10V
Fan Status: The fan status accessory is a field- - installed
accessory. This accessory detects when the indoor fan is
blowing air. When installing this accessory, the unit must
be configured
MENU Config Inputs
→ →
Status and normally open (N/O) or normally closed (N/C).
Input 8 or 9 is recommended for easy of installation. Refer
to Fig. 65 and Fig. 67 or Fig. 68 for wire terminations at
J5.
Remote Occupancy: The remote occupancy accessory is
a field- - installed accessory. This accessory overrides the
unoccupied mode and puts the unit in occupied mode.
When installing this accessory, the unit must be
configured for
MENU Config Inputs
→ →
Occupancy and normally open (N/O) or normally closed
(N/C).
Also set MENU
→
on/off. Input 8 or 9 is recommended for easy of
installation. Refer to Fig. 65 and Table 8 for wire
terminations at J5.
Power Exhaust (output): The relay used by the RTU
Open board to control power exhaust is a dry contact
which means it does not have 24vac. This 24vac must be
connected to the relay to allow it to operate the power
exhaust relay in the PE accessory. A 24vac source must be
provided to J11- - 2 on the RTU Open control board. This
can be provided by the unit's transformer from various
sources. The "R" terminal on the unit's low voltage
terminal board (LVTB) is a logical source. Refer to Fig.
65 and Fig. 67 or Fig. 68 for wire terminations at J11.
38
Relative Humidity Sensor
(Polarized Male Connector)
for fan status by
input 3, 5, 8, or 9 to Fan
→
remote occupancy by
input 3, 5, 8, or 9 to Remote
→
Schedules occupancy source to DI
→
C10839
setting
setting