Related Manuals for Pioneer GM-ME600X6
Summary of Contents for Pioneer GM-ME600X6
- Page 1 Owner’s Manual Mode d’emploi MARINE 6-CHANNEL AMPLIFIER AMPLIFICATEUR 6 CANAUX MARIN GM-ME600X6 English Français...
-
Page 2: Information To User
Pioneer service company for after- sales service or questions you may have about the product. You may contact Pioneer directly Note as follows: This equipment has been tested and found... - Page 3 Use adequate tions not authorized in writing by Pioneer are gauge, marine grade electrical wire that has excluded from limited warranty coverage.
-
Page 4: Setting The Unit
Be sure to record this number on the enclosed warranty card before installation. 3 GAIN volume Adjusting gain volume CH A (channel A), CH B (channel B), and CH C (channel C) helps align the headunit output to the Pioneer amplifier. Default setting is the... -
Page 5: Setting Gain Properly
To NOR (normal) position. For use with an ensure continuous sound output with the RCA equipped Pioneer stereo with max- headunit at a high volume, set the ampli- imum output of 4 V or more, adjust level fier gain volume to a level appropriate to match that of the stereo output. - Page 6 Signal waveform when outputting Connecting the units volume Connection diagram If the signal waveform is distorted due to high output, even if the amplifier gain is raised, the output power will change only slightly. Precise Frequency Selection Chart The numbers in the illustration correspond to the Step Number.
- Page 7 Please see the following section for speaker connection instructions. Refer to of speaker Connections when using the speaker input wire . Regarding the speaker to be connected to the f System remote control wire (sold amplifier, use a speaker having a rated input separately) capacity more than the rated output capacity of the amplifier.
- Page 8 Speaker setting and I/O Corresponding I/O for the number of input channels Input: Two-channel / Output: Six-channel Slide INPUT SELECT switch to 2CH position and connect wires with RCA pin plugs (sold sepa- rately) to CH-A. INPUT OUTPUT CH-A CH-A CH-B CH-B CH-C...
- Page 9 Input: Six-channel / Output: Six-channel Slide INPUT SELECT switch to 6CH position and connect wires with RCA pin plugs (sold sepa- rately) to CH-A, CH-B, and CH-C. INPUT OUTPUT CH-A CH-A CH-B CH-B CH-C CH-C Example of speaker setting and speaker connection Six channel output Four channel output STEREO...
-
Page 10: Connections When Using The Speaker Input Wire
Solderless terminal Speaker setting and power output connections MONO SPEAKER SETTING Since the wire may become loose over time, 100 W it must be periodically inspected and tight- ened as necessary. 150 W 75 W Do not solder or bind the ends of the twisted wires. -
Page 11: Connecting The Speaker Output Terminals
Connecting the speaker output 1 Positive terminal 2 Battery wire (sold separately) terminals The maximum length of the wire between the fuse and the positive terminal of the bat- tery is 30 cm (12 in.). 3 Fuse (80 A) (sold separately) and then twist the wire. -
Page 12: Additional Information
Install tapping screws in such a way that the screw tip does not touch any wire. This is Use the removed screws to attach the top important to prevent wires from being cut by panel cover (fastening torque 0.6 to 0.8 vibration of the boat, which can result in fire. - Page 13 Normal mode) 100 W × 6 (at 14.4 V, 4 , High power mode) 100 W × 6 (at 14.4 V, 2 , power mode) 200 W × 3 (at 14.4 V, 4 , High power mode) Load impedance ....4 to 8 allowable) Frequency response ....
- Page 14 TEL: 65-6378-7888 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 5 Arco Lane, Heatherton, Victoria, 3202 Australia TEL: (03) 9586-6300 PIONEER ELECTRONICS DE MÉXICO S.A. DE C.V. Blvd.Manuel Ávila Camacho 138, 10 piso Col.Lomas de Chapultepec, México, D.F. 11000 TEL: 52-55-9178-4270 FAX: 52-55-5202-3714 ©...