Alcatel-Lucent M7 Configuration Manual
  1. Manuals
  2. Brands
  3. Alcatel-Lucent Manuals
  4. IP Phone
  5. M7
  6. Configuration manual

Alcatel-Lucent M7 Configuration Manual

Hide thumbs Also See for M7:
Table of Contents

Advertisement

Quick Links

Home
PBXware
SERVERware
TELCOware
SIPmon
SIPProt
Desktop & Mobile
BRM
UADs
Appliances
EOL
From Bicom Systems Wiki
Contents
1 Introduction
Introduction

Advertisement

Table of Contents
loading

Related Manuals for Alcatel-Lucent M7

Summary of Contents for Alcatel-Lucent M7

  • Page 1: Table Of Contents

    Home PBXware SERVERware TELCOware SIPmon SIPProt Desktop & Mobile UADs Appliances From Bicom Systems Wiki Contents 1 Introduction 2 Requirements 2.1 Identifying Phone Model 2.2 Phone Firmware 2.3 DHCP Server 2.4 PBXware Version 3 Installation 3.1 Power Adapter 3.2 Power over Ethernet (PoE) 3.3 Find the Phone's IP Address 3.4 Reset to Factory Settings 4 Registering Phone...

  • Page 2: Requirements

    This configuration guide is written as a general guide on how to configure the Alcatel-Lucent M7 phone model to work with PBXware 5.3.9 and 6.4. Requirements Identifying Phone Model To start and successfully complete the registration of your Alcatel-Lucent phone, you need to know which phone model to set up.

  • Page 3: Dhcp Server

    DHCP Server Fully configured and operational DHCP server. PBXware Version PBXware version 5.3.9 In order to find out the PBXware version: Log in to PBXware Navigate to Settings: About. On the top of About page, you may see a code similar to this one PBXware Edition: Multi- Tenant Release: 5.3.9.0 (41a4f0e6) Running: 13.23.1-gc-2e09fa3d, Proxy v5.3.9...

  • Page 4: Find The Phone's Ip Address

    Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant. Find the Phone's IP Address Find out your Alcatel phone's IP Address. Press the OK button. The IP address will be displayed on the top of display. Reset to Factory Settings This step is not required for brand new out-of-the-box phones, however, if the phone has been already used, then it is a must.
  • Page 5 UAD settings Navigate to Settings: UAD. Make sure Alcatel M7 UAD is enabled. To check the UAD status, click the Edit icon corresponding to your Alcatel phone. Make sure Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes.
  • Page 6 E-mail Enter the e-mail address associated with this Extension. This e-mail address will receive all system notification messages. Example: john.smith@bicomsystems.com Department Department to which Extension belongs. Example: Sales. Click the Save button. Registering a Phone This section describes how to register the Alcatel phone using Hostname or IP Address. Hostname or IP Address Log in to the phone's web administration interface Open a new browser window and enter your phone IP address in order to access the phone's...

  • Page 7: Auto Provisioning

    PBXware Extension number. Example 1003. Password The Secret of the Extension as received in the e-mail associated with this extension. Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created Extension. SIP Server Enter the Hostname or IP Address of PBXware. - Example of a Hostname: voip.bicomsystems.com - Example of an IP Address: 192.168.1.10 Click the Confirm button at the bottom of the page.
  • Page 8 Navigate to Settings: UAD. Make sure Alcatel M7 UAD is enabled. To check the UAD status, click the Edit icon corresponding to your Alcatel phone. Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.
  • Page 9 Enter the Alcatel phone's MAC address. Example: 001565FF1536. The MAC address can be found at the back of the phone. Click Save. Registering a Phone This section describes how to register the Alcatel phone using DHCP, TFTP, or HTTP & HTTPS.
  • Page 10 Example of a Hostname using HTTPS: https://abc.bicomsystems.com/prov Example of an IP Address using HTTP: http://192.168.1.10/prov Example of an IP Address using HTTPS: https://192.168.1.10/prov Enter Auto Provisioning username and password into the Username and Password fields. If you choose to use TFTP, enter tftp:// followed by Hostname or IP Address Example of a Hostname: tftp://voip.bicomsystems.com Example of an IP Address: tftp://192.168.1.10 Click the Confirm button at the bottom of the page.

  • Page 11: Additional Configuration Template

    Dial *123 to verify registration. Additional Configuration Template If you want to include some additional UAD configuration for Alcatel-Lucent M7, just add fields to User Agent General Auto Provisioning Template in Settings -> UAD -> Alcatel M7 menu, or add them directly to the Extension in the UAD Auto Provisioning Template section.

Table of Contents