DeWalt DW872 Original Instructions Manual page 13

• Always set the spark deflector correctly.
• Do not attempt to cut excessively small pieces. Never perform
cuts on small workpieces bundled together.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Do not apply excessive pressure to the tool.

WARNING: Avoid overloading. Should the tool
become hot, let it run a few minutes under no
load condition.
Soft Start Feature
Time Delay Relay (TDR)
The soft start feature allows a slow speed run-up over 300 ms to
avoid an initial jerk when starting. This feature is also particularly
useful when the installed fuse value is too low or not of
inert character.
Performing a Cut (Fig. A)
1. Place the material to be cut against the fence
towards the operator as possible. Secure using the material
clamp .
6
2. Switch on the machine and pull down the main handle
to cut the workpiece. Allow the motor to reach full speed
before cutting.
3. Allow the blade to cut freely. Do not force.
4. After completing the cut, switch off the machine and return
the arm to its upper rest position.
Switching On and Off (Fig. A)
The on/off switch 1 is mounted in the main handle
To run the tool, press the on/off switch
Keep the on/off switch depressed while performing
the operation.
To stop the tool, release the switch.

WARNING: Do not switch the tool on or off when
under load.

WARNING: Do not cut magnesium.
Transporting (Fig. F)
The tool is equipped with a lock-down pin
tool in closed-down position for carrying.
1. Lower the guard onto the cutting table
4
tool in this position by pushing in the lock-down pin
2. Transport the tool using the carrying handle
3. To release the tool, pull out the lock-down pin
7 and as far
2
2 .
1 .
21 which locks the
and secure the
9
21 .
3 .
21 .
Proper Hand Position (Fig. A, G)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
and the other hand holding the workpiece away from the blade.

WARNING:
• Never place your hands near the cutting area.
• Hold the workpiece tightly to the table and the fence
when cutting. Keep your hands in position until
the switch has been released and the blade has
completely stopped.
• Do not cross your hands.
• Keep both feet firmly on the floor and maintain
proper balance.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
English
2
WALT recommended
e
11