Panasonic KX-FB423CN Manual page 266

6.2.3. SERVICE FUNCTION TABLE
Code Function
501 Pause time set
502 Flash time
503 Dial speed select
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
550 Memory clear: To reset the value to the default one, except the top margin
(853).
551 ROM check
552 DTMF single tone test
553 Monitor on FAX communication
select
554 Modem test
555 Scan check
556 Motor test
557 LED test
558 LCD test
559 Document jam detection select
561 KEY test
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection
time set
573 Remote turn-on ring number set
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
593 Time between CED and 300bps
594 Overseas DIS detection select
595 Receive error limit value set
596 Transmit level set
598 Receiving sensitivity
599 ECM Frame size
717 Transmit speed selection
Set Value Effective Default
Range
X 100 msec 001~600
X 10 ms 01~99
1:10 pps 2:20 1, 2
pps
1:2100 Hz 1, 2
2:1100 Hz
1:ON 2:OFF 1, 2
1:ON 2:OFF 1, 2
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1:ON 2:OFF 1, 2
1:OFF 1~3
2:PHASE B
3:ALL
1:ON 2:OFF 1, 2
1:61% 2:67% 1, 2
X number of 00~14
times
X second 001~999
X number of 01~99
rings
X number of 00~14
times
X second 001~999
1:OFF 1~3
2:ALL
3:AUTO
1:75 msec 1~3
2:500 msec
3:1 sec
1:detects at 1, 2
the 1st time
2:detects at
the 2st time
X Number of 001~999
times
X dBm - 15~00
43= -43 dBm 20~48
1:256 / 2:64 1,2
1:14400BPS 1~6
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
55
Remarks
30 ----------
70 ----------
1 ----------
1 ----------
1 ----------
1 The resolution reverts to the default when
transmission is complete.
1 When the telephone station is far from the unit or
reception cannot be performed correctly, adjust
accordingly.
1 When the telephone station is far from the unit or
transmission cannot be performed correctly, adjust
accordingly.
"START" input
See TEST FUNCTIONS (P.57).
2 See TEST FUNCTIONS (P.57).
1 Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or not.
See TEST FUNCTIONS (P.57).
See TEST FUNCTIONS (P.57).
0 See TEST FUNCTIONS (P.57).
See TEST FUNCTIONS (P.57).
See TEST FUNCTIONS (P.57).
1 See DOCUMENT JAMS - SENDING (P.27).
See TEST FUNCTIONS (P.57).
1 Sets the % break of pulse dialing according PBX.
05 Selects the number of times that ITS is redialed
(not including the first dial).
065 Sets the interval of ITS redialing.
10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
05 Selects the number of redial times during FAX
communication (not including the first dial).
065 Sets the FAX redial interval during FAX
communication.
2 Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A.
AUTO: CNG id output only when automatic dialing
is performed. OFF: CNG id not output at phase A.
Refer to SOMETIME THERE IS A TRANSMIT
PROBLEM (P.84).
1 ----------
1 ----------
100 Sets the number of acceptable error lines when
the FAX reconstructs the received data. Refer to
RECEIVE PROBLEM (P.85).
-10 Selects the FAX transmission level. Refer to
SOMETIME THERE IS A TRANSMIT PROBLEM
(P.84) and RECEIVE PROBLEM (P.85).
40 Used when there is an error problem.
1 ----------
1 Adjusts the speed to start training during FAX
transmission. Refer to SOMETIME THERE IS A
TRANSMIT PROBLEM (P.84).
KX-FB423CN