Page 1
This file is provided FREE OF CHARGE from the electromaniacs.com community You are free to distribute this file to other persons who needs it , but without of charge Also on http://electromaniacs.com you can find thousands of service manuals , schematics free of charge...
Page 2
ORDER No. 00-SM-022 Colour Television TX-29AS10C TX-29AS10C/B EURO- 4H Chassis SPECIFICATIONS TECHNISCHE DATEN Power Source: 220-240V a.c., 50Hz Netzspannung: 220-240V a.c., 50Hz Power Consumption: 141W Leistungsaufnahme: 141W Standby Power Standby Consumption: 1,4W Leistungsaufnahme: 1,4W Aerial Impedance: 75Ω unbalanced, Coaxial Type Antennenimpedanz: 75Ω...
CONTENTS INHALT SAFETY PRECAUTIONS ............ 2 SICHERHEITSVORKEHRUNGEN ........2 SERVICE HINTS ..............4 SERVICE HINWEISE ............4 SERVICE POSITION ............5 SERVICEPOSITION FÜR DAS CHASSIS ......5 SELF CHECK ..............6 SELBSTDIAGNOSE ............6 ADJUSTMENT PROCEDURE ..........7 ABGLEICH ................7 WAVEFORM PATTERN TABLE ..........
Page 4
LEAKAGE CURRENT HOT CHECK MESSUNG DES KRIECHSTROMS IM Plug the a.c. cord directly into the a.c. outlet. Do not EINGESCHALTETEN ZUSTAND use an isolation transformer for this check. Den Netzstecker direkt in eine Netsteckdose stecken. Connect a 2kΩ 10W resistor in series with an Für diese Messung keinen Trenntransformator exposed metallic part on the receiver and an earth, verwenden.
SERVICE HINTS SERVICE HINWEISE HOW TO REMOVE THE REAR COVER ENTFERNEN DER GERÄTERÜCKWAND Remove the 8 screws as shown in Fig. 2. Die 8 Schrauben entfernen, siehe Abb. SCREWS SCREWS SCHRAUBEN SCHRAUBEN Fig. 2 Abb. 2 LOCATION OF CONTROLS LAGE DER EINSTELLREGLER Y-Board P-Board M-Board...
HOW TO MOVE THE CHASSIS SERVICE POSITION INTO SERVICE POSITION FÜR DAS CHASSIS Die 2 Schrauben (A) entfernen, wie in dargestellt, und Remove 2 screws (A), as shown in Fig.4., and Abb.4. remove speaker assembly. die Lautsprechereinheit herausnehmen. Hold and lift the rear of the chassis and gently pull Das Chassis leicht anheben und nach hinten herausziehen, wie in dargestellt.
SELF CHECK SELBSTDIAGNOSE Self-check is used to automatically check the bus Die Selbstdiagnose dient zum automatischen Prüfen lines and hexadecimal code of the TV set. der Bus-Leitungen sowie des Hexadezimalcodes des FS-Geräts. Zum Umschalten auf Selbstdiagnose zunächst die Taste "STATUS" auf der To get into the Self-Check mode press the down (-/v) button on the customer controls at the front of Fernbedienung und gleichzeitig die-Taste am...
ALIGNMENT SETTINGS: (The figures below are nominal and used for representative purposes only.) Set the Bass to maximum position, set the Treble to minimum position, set the Volume to minimum then press the down button (-/v) on the customer controls at the front of the TV and at the same time press the INDEX button on the remote control, this will place the TV into the Service Mode.
ABGLEICHTABELLE (Die angegebenen Werte sind Mittelwerte und Können individuell nach oben oder unten nach dem korrekten Abgleich abweichen.) Um in den Service-Mode zu gelangen, gehen sie bitte wie folgt vor. Stellen sie im Toneinstellungs-Menü die Bässe auf Maximun, die Höhen auf Minimum und die Lautstärke auf Minimum. Halten sie die INDEX-Taste auf der Fernbedienung gedrückt und drücken zusätzlich die Taste -/v im Bedienteil des TV- Gerätes.
VIDEO BLOCK DIAGRAM BILDSIGNAL BLOCKSCHEMA F - BOARD E - BOARD IC1503 IC1502 UP-CONVERTER COMPONENT C OUT 10-16 63 BU INTERFACE Y OUT 3-7, 1, 63, 64 PROCESSOR 8 bit C IN 37-44 65 GY Q104 TUNER C OUT 10-17 8 bit Y IN 43-50 Y OUT 20-27...
Page 13
AUDIO BLOCK DIAGRAM TONSIGNAL BLOCKSCHEMA M - BOARD IC2101 AUDIO E - BOARD PROCESSOR E16A IC251 DACM_R 24 Q2102 AUDIO TUNER OUTPUT Q2103 L 11 DACM_L 25 HEADPHONE SC3_IN_L 37 SC3_IN_R 38 Q101 1 R OUT SC1_OUT_R 30 Q102 47 ANA_IN1+ SC1_IN_R 42 2 R IN AUDIO...
Page 14
CONTROL BLOCK DIAGRAM KONTROLL BLOCKSCHEMA E - BOARD Y - BOARD TUNER Q351 Q2301 MUTE Q2303 SENSE IC601 Q361 D_CTR_OUT1 AV VIDEO IC2101 SWITCH Q371 AUDIO D_CTR_OUT0 PROCESSOR Q601 SDA 1 SERVICE / TEST SCL 1 SDA 1 SCL 1 SDA 2 F - BOARD SCL 2...
Page 15
POWER SUPPLY BLOCK DIAGRAM STROMVERSORGUNGS BLOCKSCHEMA E - BOARD M - BOARD Q852 5V SBY E16A IC1061 REMOTE D867 Q855 CONTROL D868 Q853 Q854 RECEIVER IC251 AUDIO D862 T802 RL801 R854 OUTPUT T801 D801 Line Filter Y - BOARD 150V 150V D850 IC351...
PARTS LOCATION EXPLOSIONSZEICHNUNG NOTE: ANMERKUNG: The numbers on the exploded view below Die Nummern auf den Teilen der refer to the exploded view section of the Explosionszeichnung zeigen die Replacement Parts List. Bezugsnummern des Artikels der Explosionszeichnung der Ersatzteilliste an. www.rtv-horvat-dj.hr...