Husqvarna Automower 550 EPOS Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Lawn Mower
  5. AUTOMOWER 550 EPOS
  6. Operator's manual

Husqvarna Automower 550 EPOS Operator's Manual

Hide thumbs Also See for Automower 550 EPOS:
Table of Contents

Advertisement

Quick Links

Download this manual
Operator's manual
®
HUSQVARNA AUTOMOWER
550 EPOS
EN, English
Read the operator's manual carefully and make sure that you
understand the instructions before you use the product.

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna Automower 550 EPOS

Summary of Contents for Husqvarna Automower 550 EPOS

  • Page 1 Operator's manual ® HUSQVARNA AUTOMOWER 550 EPOS EN, English Read the operator's manual carefully and make sure that you understand the instructions before you use the product.

  • Page 2: Table Of Contents

    Contents 6.3 Information and warning messages....34 1 Introduction 6.4 LED indicator lamp on the charging station..34 1.1 Support..............3 6.5 LED indicator on the product.......35 1.2 System description..........3 6.6 Symptoms............36 1.3 Product description..........3 7 Transportation, storage and disposal 1.4 System overview...........

  • Page 3: Introduction

    The serial number and the product number are on the product rating plate and on the product carton. • Register your product on www.husqvarna.com. Enter the serial number of the product, the product number and the date of purchase to register your product.

  • Page 4: System Overview

    1.4 System overview Satellites Stay-out zone Satellite signals Work area Reference station Mobile device Correction data 10. Docking point Charging station 11. Transport path Virtual boundary Not included. Not included. 4 - Introduction 1576 - 004 - 16.11.2021...

  • Page 5: Product Overview

    1.5 Product overview Body 16. Low-voltage cable LED indicator lamp of the product 17. Power supply STOP/START button 18. Extra blades Ultrasonic sensors 19. Screws for securing the charging station Front wheels 1.6 Symbols on the product Rear wheels Cutting system These symbols can be found on the product.

  • Page 6: Symbols On The Battery

    WARNING: Read the user in- The low-voltage cable must not be structions before operating shortened, extended or spliced. the product. Do not use a trimmer nearby the low- voltage cable. Be careful when trimming edges where the cables are placed. WARNING: Disable the prod- uct before working on or lift- ing the product.

  • Page 7: General Manual Instructions

    1.9 General manual instructions The following system is used in the Operator’s Manual to make it easier to use: italics is a text that is in the • Text written in ® Automower Connect app, or is a reference to another section in the Operator’s manual.

  • Page 8: Safety

    2 Safety 2.1 Safety information 2.1.1 IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE The operator is responsible for accidents or hazards occurring to other people or property. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities (that could affect a safe handling of the product), or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person...

  • Page 9: Safety Definitions

    The appliance must be disconnected from the supply mains when removing the battery. WARNING: The product CAUTION: Used if there is a risk of damage to the product, other materials or can be dangerous if used the adjacent area if the instructions in the manual are not obeyed.
  • Page 10 Schedule on page 20 . Refer to blades hit foreign objects the blades can be • Husqvarna does not guarantee full compatibility damaged. Always switch off the product before between the product and other types of wireless clearing a blockage. Inspect the product for systems such as remote controls, radio damage before starting the product again.
  • Page 11 The Main switch should be set in the WARNING: The product must be position before all work on the chassis of the switched off before lifting it. The product is product, such as cleaning or replacing the disabled when the Main switch is in position blades.

  • Page 12: Installation

    Read and understand the instructions about where to Note: Refer to www.husqvarna.com for more put the reference station. Refer to the Operator's manual information about installation. for the reference station. 3.5 To examine where to put the 3.2 Primary components for installation...

  • Page 13: To Examine Where To Put The Power Supply

    3 m / 9.8 ft. • If the work area has 2 parts separated with a steep slope, Husqvarna recommends to put the charging station in the lower section. CAUTION: Do not install the charging station where there are metal objects in the ground.

  • Page 14: To Examine Where To Install The Objects On The Map

    3.7 To examine where to install the • Make sure that there are no trees with thick vegetation in the areas where the product objects on the map operates. • Make sure that the product can receive radio CAUTION: If the work area is adjacent signals from the reference station in all parts of the to water bodies, slopes, precipices or a work area.
  • Page 15 The product is only to be supplied screws. used with the power supply unit supplied by Connect the low-voltage cable to the charging Husqvarna. station. Put the power supply at a minimum height of 30 To examine where to put the cm / 12 in.
  • Page 16 ™ more information about Husqvarna Fleet Services refer to www.husqvarna.com. 3.8.4 Installation of the reference station 3.8.6.1 To connect to the product with Husqvarna Fleet Install the reference station according to the instructions ™ Services in the Operator's manual for the reference station.
  • Page 17 If GeoFence is to be used, select to enable the There are two types of work areas: function. • A work area that has a charging station in it or connected to it with a transport path where the Note: It is only necessary to do a pairing operation of product operates automatically.
  • Page 18 Note: The position of the waypoint when you install a work area or a stay-out zone is in the front left corner of the product. Note: Walk 2-3 m / 6.5-9.8 ft. behind the product when you operate the product with appDrive. To make a work area Minimum 3 waypoints are necessary to make a work Note:...
  • Page 19 • Operate the product counterclockwise around the boundary of the stay-out zone. • Add waypoints on the map. Add the waypoints minimum 3 cm / 1 in. from obstacles. • Do not set waypoints that make a virtual boundary go across itself in the same stay-out zone. •...

  • Page 20: Settings

    • Operate the product and add waypoints to make a Note: The operation capacity is approximate and is path to the charging station. calculated for flat and open work area. If the work area • Save the maintenance point to automatically has a lot of slopes or obstacles, you need to increase connect the last waypoint to the docking point.
  • Page 21 The headlights can also be set to flash if there is an error. 3.9.3.2 Weather timer Note: Husqvarna recommends to use the headlights Weather timer automatically adjust the cutting time to at night time. the growth of the grass. The product is not permitted to operate more than the schedule settings.
  • Page 22 3.9.8 Messages 3.9.6.1 New loop signal The loop signal is randomly selected to create a unique In this menu the previous fault and information link between the product and the charging station. In messages can be found. For some of the messages, rare cases, there may be a need to generate a new there are tips and advice to help to rectify the fault.

  • Page 23: Operation

    4 Operation 4.1 Main switch 4.3.2 appDrive Use the appDrive to operate the product manually. WARNING: Read the safety 4.3.2.1 To operate the product with appDrive instructions carefully before you start the product. Use the buttons to operate the product: •...

  • Page 24: To Stop The Product

    operation mode is selected and the START button is WARNING: Always switch off the pushed. product using the Main switch if it requires 4.4.2 Select duration maintenance, or if the product must be moved outside the work area. The product goes back to the charging station and stays for the selected park duration.

  • Page 25: Maintenance

    Do not use a high-pressure washer or running water to clean the 5.2 Clean the product charging station. Husqvarna recommends to use a special cleaning and maintenance kit, available as an accessory. Speak to Note: your Husqvarna representative for more information.

  • Page 26: Replacement Of The Blades

    Remove the 3 screws with a screwdriver. 5.6 Winter service Take your product to your Husqvarna central service for service prior to winter storage. Regular winter service will maintain the product in good condition and create the best conditions for a new season without any disruptions.
  • Page 27 • Testing of the product’s function and components. • Checking and, if required, replacing wear items such as blades and bearings. • Testing the product’s battery capacity as well as a recommendation to replace battery if necessary. • If new firmware is available, the product is updated.

  • Page 28: Troubleshooting

    Messages menu in Automower ® All messages can be found in the Connect. More suggestions for steps to take in the event of malfunction or symptoms can be found on www.husqvarna.com. Note: Messages menu is only available for short-range connectivity (Bluetooth ®...
  • Page 29 Message Cause Action No loop signal The power supply or the low-voltage ca- If the LED indicator on the charging sta- ble for the charging station is not connec- tion is out, it shows that there is no pow- ted. er.
  • Page 30 Message Cause Action Empty battery The product cannot find the charging sta- The product has no accurate position tion. and cannot find the charging station. There is an obstacle that prevents the product to find the charging station. Battery on The battery is at the end of its life cycle.
  • Page 31 Message Cause Action Wheel motor blocked right/ The wheel is blocked by grass or other Examine the wheel and remove grass or left objects. other objects. Alarm! Mower stopped Securi- The alarm was started because the prod- Adjust the security settings in the ®...
  • Page 32 Message Cause Action Map problem ® There is no specified work area. Make a work area in the Automower To make a work Connect app. Refer to area on page 18 . The charging station or the reference sta- Move the charging station or the refer- tion was moved.
  • Page 33 Message Cause Action Reference station communi- The product is not connected to the refer- Do a pairing operation between the prod- cation problem ence station. uct and the reference station. The reference station is not installed cor- Examine the installation of the reference rectly.

  • Page 34: Information And Warning Messages

    For a fully functional installation, the indicator lamp in the charging station must show a solid or flashing green light. If another color shows, follow the troubleshooting guide below. There is more help on www.husqvarna.com. If you still need help, speak to your local Husqvarna representative. Light...

  • Page 35: Led Indicator On The Product

    The product sets to OFF. Firmware installation is in progress. Flashes white New firmware must be installed. There is more information on www.husqvarna.com. Speak to your local Husqvarna representative for more information. 1576 - 004 - 16.11.2021 Troubleshooting - 35...

  • Page 36: Symptoms

    6.6 Symptoms If your product does not work as expected, follow the symptoms guide below. Symptoms Cause Action The Main switch is set to 0 The Main switch was set to 0 when the Set the Main switch to 1 and connect the ®...
  • Page 37 Symptoms Cause Action The product is parked for The product is parked due to a schedule Open the app and edit the schedule set- Park until further no- Dashboard and start the hours in the charging station. setting, or because tings, or go to tice has been chosen in the app.

  • Page 38: Transportation, Storage And Disposal

    Keep the product in a dry, frost free space. a Torx 20. • Keep the product with all wheels on level ground during storage, or use a Husqvarna wall hanger. • If you keep the charging station indoors, disconnect and remove the power supply from the charging station.

  • Page 39: Technical Data

    8 Technical data 8.1 Technical data ® Dimensions Automower 550 EPOS Length, cm / in. 72 / 28.3 Width, cm / in. 56 / 22.0 Height, cm / in. 32 / 12.6 Weight, kg / lbs 14.4 / 31.7 ® Electrical system Automower 550 EPOS...
  • Page 40 ® Mowing Automower 550 EPOS Cutting system 3 pivoted cutting blades Maximum cutting motor speed, rpm 2700 Power consumption during cutting, W +/- 20 % Cutting height, cm / in. 2-6 / 0.8-2.4 Cutting width, cm / in. 24 / 9.4 Narrowest possible passage, m / ft.

  • Page 41: Registered Trademarks

    5 . 8.2 Registered trademarks Bluetooth ® Bluetooth SIG, inc. and any use of such word mark and logos are registered trademarks owned by marks by Husqvarna is under license. 1576 - 004 - 16.11.2021 Technical data - 41...

  • Page 42: Warranty

    The blades and wheels are seen as disposable and are not covered by the warranty. If an error occurs with your Husqvarna product, please contact Husqvarna customer service for further instructions. Please have the receipt and the product’s serial number at hand when contacting Husqvarna customer service.
  • Page 43 10 EU Declaration of Conformity We, Husqvarna AB, SE 561 82 Huskvarna, SWEDEN, Tel. +46 36 146500 declare on our sole responsibility that the product: Description Robotic lawn mower Brand Husqvarna Type/Model HUSQVARNA AUTOMOWER ® 550 EPOS Identification Serial numbers dating from 2021 week 40...
  • Page 44 11 UK Declaration of Conformity We, Husqvarna AB, SE 561 82 Huskvarna, SWEDEN, Tel. +46 36 146500 declare on our sole responsibility that the product: Description Robotic lawn mower Brand Husqvarna Type/Model HUSQVARNA AUTOMOWER ® 550 EPOS Identification Serial numbers dating from 2021 week 40...
  • Page 45 1576 - 004 - 16.11.2021 UK Declaration of Conformity - 45...
  • Page 46 46 - UK Declaration of Conformity 1576 - 004 - 16.11.2021...
  • Page 47 1576 - 004 - 16.11.2021 UK Declaration of Conformity - 47...
  • Page 48 AUTOMOWER ® is a trademark owned by Husqvarna AB. © Copyright 2021 HUSQVARNA. All rights reserved. www.husqvarna.com Original instructions 1142739-26 2021-12-03...

Table of Contents