Advertisement
S
R
AFETY AND
EGULATORY
E
NGLISH
f
WARNING!
Read all warnings, cautions, notes and installation
instructions before installing or servicing this equipment.
C
CAUTION!
This product contains a Class 1 Laser that complies with
FDA 21 CFR 1040.10, 1040.11 and 60825-1.
f
CAUTION!
■
Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing
material when transporting or storing. When working on
modules, always place them on an approved antistatic
mat that is electrically grounded.
■
This product and the host system are designed and
intended for installation as part of a Common Bonding
Network (CBN).
■
This product's outer case may not be "electrically
isolated" from other circuits. As a result, this product can
only be used is systems that are installed in a DC-C
(common) configuration.
■
If the host system has a protective earth (PE) terminal,
the PE terminal of the host system must be connected to
protective earth (PE) to ensure that the exposed metal
(i.e., front panels, optical modules) on the product is
properly grounded.
g
NOTE
■
This product is NRTL listed to the applicable UL
Standards.
■
The product is designed to meet the applicable
requirements of Telcorida GR-3108-CORE and GR-
1089-CORE. This product has also been evaluated to
applicable international standards and meets the
requirements of CE marking.
■
This product is intended for deployment in locations
such as business, residential, outside plant cabinets,
and inside remote DSLAMs and DPUs. This product is
to be installed and serviced by trained and qualified
Service Personnel only.
■
This product is designed to be deployed in GR-3108-
CORE environmental Class 1, 2 or 3.
■
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: 1.
This device may not cause harmful interference, and (2)
this device must accept any interference received,
2
including interference that may cause undesired
operation.
■
Changes or modifications not expressly approved by
ADTRAN could void the user's authority to operate this
equipment.
■
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
♦
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
♦
receiver.
♦
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
♦
Consult the dealer or an experienced radio/TV
technician for help.
■
CAN ICES-3(B)/NMB-3(B)
■
This product is designed to meet the following
environmental classes:
♦
ETSI EN 300 019-1-1 "Classification of environmental
conditions; Storage," Class 1.2
♦
ETSI EN 300 019-1-2 "Classification of environmental
conditions; Transportation," Class 2.3
♦
ETSI EN 300 019-1-3 "Classification of environmental
conditions; Stationary use at weather-protected
locations," Class 3.4
■
The equipment is designed to function without
degradation during exposure to all test severities per
Class 3.4.
■
This product meets EU RoHS Directive. Refer to
www.adtran.com
for further information on RoHS/
WEEE.
61200488F3-13A
Advertisement
