Table of Contents
Advertisement
28 | English
To exit the menu item, press the on/off/delete button (9) [
] or the soft key (3) [
]. The selected tool settings remain
saved after you switch off the measuring tool.
TrackMyTools
Select the TrackMyTools option in the tool settings menu.
Confirm the setting by pressing the button (13) [Func].
Initial activation is required. Data can only be transmitted us-
ing a suitable app or computer program.
TrackMyTools can be deactivated again at any time.
Display illumination
Select the dimmer option in the tool settings menu.
The display illumination is continuously switched on. If you
do not press any buttons, the display lighting is dimmed
after approximately 30 seconds to preserve the battery.
The time until dimming starts can be adjusted (tool settings).
The brightness of the display can be adjusted to the sur-
rounding conditions in multiple increments (tool settings).
Measuring functions
Note: Integrated help function
Help in the form of an animation is saved in the measuring
tool for each measuring function. To access this, select the
button (13) [Func], the button (4) [+] or button (11) [−]
and then the soft key (3) [
detailed procedure for the selected measuring function.
The animation can be stopped and started again at any time
using the soft key (3) [
]. You can scroll forwards and
backwards using the button (4) [+] and button (11) [−].
Measuring length
Select the length measurement mode
To switch on the laser beam, briefly press the measuring but-
ton (2) [ ].
To measure, briefly press the measuring button (2) [ ]. The
measured value will be shown at the bottom of the display.
Repeat the above-mentioned steps for each
09.06.2017
13:20:23
subsequent measurement. The last measured
4.640
m
0.0º
9.279
m
value is at the bottom of the display, the penul-
13.919
m
18.558
m
timate measured value is above it, and so on.
23.198 m
Continuous measurement
In continuous measurement mode, the measuring tool can
be moved relative to the target, during which the measured
value will be updated every half a second. You can, for ex-
ample, move a desired distance away from a wall while read-
ing off the current distance at all times.
Select the continuous measurement mode
To switch on the laser beam, briefly press the measuring but-
ton (2) [ ].
Move the measuring tool until the required distance value is
shown in the display below.
1 609 92A 4F4 | (22.10.2018)
]. The animation shows you the
.
.
Briefly pressing the measuring button (2) [ ]
09.06.2017
13:20:23
will interrupt the continuous measurement.
0.0º
1.291
m
min
The current measured value will be shown at
11.623
m
max
the bottom of the display. The maximum and
11.623
m
minimum measured value appear above it.
Pressing the measuring button (2) [ ] once
more will start the continuous measurement again.
Continuous measurement automatically switches off after
five minutes.
Area measurement
Select the area measurement mode
Then measure the width and length and height one after the
other as with a length measurement. The laser beam remains
switched on between the two measurements. The distance
to be measured flashes in the indicator for area measure-
ment
(see indicator element (j)).
The first measured value is shown at the top of
09.06.2017
13:20:23
the display.
0.0º
4.640
m
After the second measurement has been com-
9.279
m
pleted, the area will be automatically calcu-
2
43.050 m
lated and displayed. The end result is shown at
the bottom of the display, while the individual
measured values are shown above it.
Volume measurement
Select the volume measurement mode
Then measure the width, length and depth one after the
other as with a length measurement. The laser beam remains
switched on between the three measurements. The distance
to be measured flashes in the indicator for volume measure-
ment
(see display element (j)).
The first measured value is shown at the top of
09.06.2017
13:20:23
the display.
0.0º
4.640
m
After the third measurement has been com-
9.279
m
13.919
m
pleted, the volume will be automatically calcu-
3
599.276 m
lated and displayed. The end result is shown at
the bottom of the display, while the individual
measured values are shown above it.
Indirect distance measurement
Select the indirect distance measurement mode . There
are four measuring functions available for the indirect dis-
tance measurement, each of which is capable of determining
different distances.
The indirect distance measurement is used to determine dis-
tances that cannot be measured directly, due to an obstacle
that would impede the path beam or the absence of a target
surface that could serve as a reflector. This measuring pro-
cedure can only be employed vertically. Any horizontal devi-
ation will lead to measurement errors.
Note: Indirect distance measurement is always less accurate
than direct distance measurement. For application-related
reasons, measuring errors can be greater than with direct
distance measurement. To improve the accuracy of meas-
urement, we recommend the use of a tripod (accessory).
The laser beam remains switched on between the individual
measurements
.
.
Bosch Power Tools
Advertisement
Table of Contents
