Bosch GLM165-40 Operating/Safety Instructions Manual
  1. Manuals
  2. Brands
  3. Bosch Manuals
  4. Measuring Instruments
  5. GLM165-40
  6. Operating/safety instructions manual

Bosch GLM165-40 Operating/Safety Instructions Manual

Measuring, detection and layout tool
Hide thumbs Also See for GLM165-40:
Table of Contents

Advertisement

Quick Links

Read Before Using
For English Version
Find Quality Products Online at:
IMPORTANT:
Operating/Safety Instructions
Consignes d'utilisation/de sécurité
Instrucciones de funcionamiento
y seguridad
GLM165-40
Call Toll Free for Consumer Information and Service Locations
Pour obtenir des informations et les adresses de nos centers de service
après-vente, appelez ce numéro gratuit
Llame gratis para obtener información para el consumidor y
ubicaciones de servicio
See page 4
GlobalTestSupply
www.
IMPORTANT :
Lire avant usage
IMPORTANTE:
Leer antes de usar
.com
sales@GlobalTestSupply.com

Advertisement

Table of Contents
loading

Related Manuals for Bosch GLM165-40

Summary of Contents for Bosch GLM165-40

  • Page 1 Operating/Safety Instructions Consignes d’utilisation/de sécurité Instrucciones de funcionamiento y seguridad GLM165-40 Call Toll Free for Consumer Information and Service Locations Pour obtenir des informations et les adresses de nos centers de service après-vente, appelez ce numéro gratuit Llame gratis para obtener información para el consumidor y...
  • Page 2 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
  • Page 3 5 ⁄ 1 6 ˝ 1 ´ 5 ´ 1 1 ˝ 5 ⁄ 1 6 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
  • Page 4 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...

  • Page 5: Safety Symbols

    Safety Symbols The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

  • Page 6: Electrical Safety

    DO NOT use measuring tools, attachments and accessories outdoors when lightening conditions are present. Electrical safety Batteries can explode or leak, cause injury or fire. To reduce this risk, always follow all instructions and warnings on the battery label and package. Do not short any battery terminals.
  • Page 7 Measuring, detection and layout tool use and care Use the correct measuring, detection and layout tool for your application. The correct measuring, detection and layout tool will do the job better and safer at the rate for which it was designed.
  • Page 8 When cleaning a tool be careful not to disassemble any portion of the tool since internal wires may be misplaced or pinched or may be improperly mounted. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts. Safety Rules for Laser Tools The following label is on your laser tool for your safety.
  • Page 9 Removing labels increases the risk of exposure to laser radiation. DO NOT operate the measuring tool in combustible areas such as in the presence of flammable liquids, gases or dust. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

  • Page 10: Intended Use

    Intended Use The measuring tool is intended for measuring distances, lengths, heights and clearances. The measuring tool is suitable for measuring only indoors. Features The numbering of the product features shown refers to the illustration of the measuring tool on the graphic page. 1 Display Display Elements a Temperature warning...

  • Page 11: Technical Data

    Technical Data Digital Laser Measure GLM165-40 Measuring range (typical) 6 in - 165 ft (0.15 –50 m Measuring accuracy (typical) ±1/16 in (±1.5 mm Lowest indication unit ±1/32 in (1 mm) Automatic switch-off after approx. - Laser 20 s - Measuring Tool...

  • Page 12: Inserting/Replacing The Batteries

    Assembly Inserting/Replacing the Batteries AAA Alkaline batteries are recommended for the measuring tool. To open the battery lid 7, press the latch 8 in the direction of the arrow and remove the battery lid. Insert the batteries. When inserting, pay attention to the correct polarity according to the representation on the inside of the battery compartment.

  • Page 13: Switching On And Off

    Do not leave the switched on measuring tool unattended and switch the tool off after use. Other persons could be blinded by the laser beam. Switching On and Off To switch on the measuring tool and the laser, press the measuring button 2 or the Clear/ On/Off button 5.
  • Page 14 For real time measurements, repeatedly press button 4 until the indicator for real time measurement appears on the display 1. Press Measure button 2 to activate laser. The laser will be switched on and measuring will begin immediately. Move the measuring tool until the required distance value is indicated in the bottom of the display.
  • Page 15 the bottom line will move to the middle line. Press the measuring button 2 for a new measurement on the bottom line. The last three measurements will display on the bottom, middle, and top lines. Area Measurement For area measurements, repeatedly press button 4 until the indicator for area measurement appears on the display 1.

  • Page 16: Memory Functions

    at the top of the display. The laser beam remains switched on between the two measurements. After the second measurement has been completed, the height will be automatically calculated and displayed. The end result will be shown at the bottom of the display, while the current measured value will be shown above it.
  • Page 17 Adding/subtracting measured values in real time and length measurement modes (see figure B) To measure, press the measuring button 2. The measured value will be shown at the bottom of the display. Press button 6 to add measured values or press button 3 to subtract measured values.

  • Page 18: Working Advice

    Switching the Sound On and Off The sound is switched on by default. Press and hold the function button until you see the Changing the Unit of Measure display. Press function button 4 again to see the image displayed to the left. Use button 3 and 6 to adjust the sound preference.

  • Page 19: Troubleshooting

    Accuracy Check of the Distance Measurement The accuracy of the distance measurement can be checked as follows: – Select a permanent measuring section with a length of approx. 3 ft to 33 ft (1 m to 10 m); its length must be precisely known (e.g.

  • Page 20: Maintenance And Service

    If the measuring tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an authorized after-sales service center for Bosch power tools. Do not open the measuring tool yourself. In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the measuring tool.
  • Page 21 If you are not completely satisfied with the performance of your laser and measuring tools, for any reason, you can return it to your Bosch dealer within 30 days of the date of purchase for a full refund or replacement. To obtain this 30-...
  • Page 22 THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL BOSCH DEALER OR IMPORTER. GlobalTestSupply www. .com Find Quality Products Online at:...

Table of Contents