Related Manuals for Digicom 2G Lift Dialer
Summary of Contents for Digicom 2G Lift Dialer
- Page 1 8D5778 _ 2G Lift Dialer 8D5798 _ 2G Lift Dialer MetalBox User’s Guide 7Dxxxx rev. 3.0 01/2016...
-
Page 3: Table Of Contents
2.3. TESTS DURING THE INSTALLATION ....................2.8 2.4. BEFORE POWERING LIFT DIALER ON ....................2.9 2.5. VOICE BOX CONNECTION ......................... 2.10 2.6. 2G LIFT DIALER PINOUT ........................2.11 2.7. LIFT DIALER TOPOGRAPHY ......................2.11 2.8. VOICE BOX - CAR PINOUT (CODE 8D5804) ..................2.12 2.9. -
Page 4: Preface
All rights reserved; no part of this publication may be reproduced, stored in a retrieval system, or trasmitted in any form or by any means, electronic, otherwise, without the prior written permission of Digicom S.p.A. The contents of this booklet may be modified without notice. Every possible care has been taken in testing and putting together all the documentation contained in this booklet, however Digicom can not take any responsability brought by the use of this booklet. -
Page 5: Safety Warnings
2G Lift Dialer Preface SAFETY WARNINGS Read these instructions and norms carefully before powering the device. Violation of such norms may be illegal and cause hazard situations. For any of the described situations please refer to the specific instructions and norms. -
Page 7: Introduction
Introduction INTRODUCTION Thanks for purchasing a Digicom product! 2G Lift Dialer and Voice Box constitute a bidirectional Emergency phone for lifts system, compliant to EN81.28, EN81.1, EN81.2 regulations. The Emergency phone allows the users blocked in a lift cabin to send an alarm via GSM to a Service Center or to the authorized Technical people. -
Page 8: System Description And Package Content
Voice Box Speakerphone unit with integrated microphone and speaker. Voice Box speakerphone unit is connected to 2G Lift Dialer Emergency phone with 2 wires only. For a good audio quality we suggest the use of a twisted pair for the connection. - Page 9 2G Lift Dialer Introduction Voice Box speakerphone unit, only 19mm thick and powered directly by 2G Lift Dialer Emergency phone, is available in the following versions: Voice Box Top/Pit (code 8D5780) For the installation on the Top of the cabin and in Pit with microphone and speaker.
-
Page 11: Installation
Pit buttons it is possible to use the model Voice Box Button. Furthermore in all architectures it will be possible to connect a common phone to the 2G Lift Dialer for the intercom function between the frame controller and the lift cabin. The same phone can be also used for the local configuration and for the... - Page 12 2G Lift Dialer Installation...
- Page 13 2G Lift Dialer Installation...
- Page 14 2G Lift Dialer Installation...
- Page 15 2G Lift Dialer Installation...
- Page 16 2G Lift Dialer Installation...
- Page 17 2G Lift Dialer Installation...
-
Page 18: Tests During The Installation
• connection to the terminal board of the 2 wires coming from 2G Lift Dialer; • connection of the 2 wires for the lift alarm button: the button must a 2 contact buttons to separate the circuit for the activation of the alarm call from the bell circuit;... -
Page 19: Before Powering Lift Dialer On
2.4. Before PoWering lift dialer on Place 2G Lift Dialer where you prefer, in a zone with a good GSM signal, and go on as follows: 1. Open the SIM holder by slightly pressing and pushing it horizontally toward the internal side of the card. -
Page 20: Voice Box Connection
Voice BoX connection Place the Voice Box(es) where you prefer and go on as follows: 1. Connect pins 5-6 of 2G Lift Dialer to pins 1-2 of Voice Box. PINS CAN BE CROSSED. For a good audio quality use a twisted pair for the connection. Otherwise you can use two unused wires already present in the car cable or use the the wires already present and used for the bell after having modified the system as described in paragraph RELAY1: BELL MANAGEMENT. -
Page 21: Lift Dialer Pinout
POWER (12-24Vdc) [ + ] * The battery with connector (code 7D1991) can be connected to the specific connector present on 2G Lift Dialer; if the battery has no connector, it can be connected to pins18-19 of the terminal board, paying attentions to the polarity. -
Page 22: Voice Box - Car Pinout (Code 8D5804)
2G Lift Dialer Installation 2.8. Voice BoX - car Pinout (code 8d5804) DESCRIPTION LIFT DIALER LIFT DIALER EXTERNAL ALARM BUTTON IN TOP and/or PIT (N.O. or N.C.) EXTERNAL ALARM BUTTON IN CAR (N.O. or N.C.) HEARING LOOP ( - ) -
Page 23: Voice Box - Top / Pit Pinout (Code 8D5780)
2G Lift Dialer Installation 2.10. Voice BoX - toP / Pit Pinout (code 8d5780) DESCRIPTION LIFT DIALER LIFT DIALER NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED For a good audio quality we suggest the use of a twisted pair for the connection. -
Page 24: Voice Box Button Pinout (Code 8D5810)
For installation on Top/Pit, with alarm button only, without integrated microphone and speaker. This model will have to be connected to Voice Box Car and it won't be connected to 2G Lift Dialer Emergency phone. Otherwise it is possible to use a N.O. or N.C. button. -
Page 25: Lift Dialer: Led Indicators
SERIAL PORT RS232 2.16. BacKuP Battery (code 7d1991) RESET USB PORT 2G Lift Dialer can be equipped with a backup battery (Digicom code 7D1991) to ensure proper operation in the event of RS232 ENABLED main power blackout. CONFIG Backup Battery features: Li-ion Polymer 3,7V – 3800mAh rechargeable. -
Page 26: Reset Button
2G Lift Dialer Installation 2.17. reSet Button ACTION DESCRIPTION Press and release Reboot and Alarms Reset ANTENNA The yellow GSM led will switches off for a new registration to the GSM network. Press for 10 seconds Factory default and Reboot... -
Page 27: Configuration
DIALER READY CORRECT PASSWORD CORRECT CONFIGURATION WRONG CONFIGURATION Together with the audio signals, you can verify the correct configuration from the red LED CONFIG of the 2G Lift Dialer: CORRECT CONFIGURATION WRONG CONFIGURATION 3.1. CONFIGUratION VIa lOCal phONe 1. -
Page 28: Configuration Via Sms
Password. With the configuration via SMS it is possible to send to 2G Lift Dialer several commands with a sole SMS, by inserting at the beginning of the message the Access password once only. - Page 29 01 to 31 mm: month from 01 to 12 2G Lift Dialer synchronizes the date and time with the hour of the GSM yy: year from 14 (2014) network at any power on, if supported by the operator, and after any hh: hour from 00 to 23 received SMS.
- Page 30 0 n o m e s s s a g e , d i r e c t If you don't digit anything, after the message repetitions, 2G Lift Dialer trys speakerphone to contact Car1.
- Page 31 2G Lift Dialer Configuration DESCRIPTION COMMAND Enable technical & battery alarms 5 0 [abcd] # Example 5 0 1 0 1 0 # a = external input, for example flooding sensor (pin9-10) The single values a b c d can be set to:...
- Page 32 2G Lift Dialer Configuration DESCRIPTION COMMAND Time of pressure for SOS button (VoiceBox) 9 3 [t] [c] # Example 9 3 1 # from 1 to 9 (default 5) Example 9 3 2 3 # 1 or not present = car 1...
-
Page 33: Configuration Examples
3.7. reCOrDING the alarm meSSaGe (COmmaND 40#) During the alarm call, the alarm message is played back several times by 2G Lift Dialer to the Alarm Center and/or Support service before enabling the speakerphone conversation with the Car. The recording is performed through the configuration local phone or by calling 2G Lift Dialer. -
Page 34: Managing The Alarm Call
• press 3 to enable the speakerphone in the car; code 3 can be modified with command 96*04*[d]# Once the activation code of the speakerphone has been received, 2G Lift Dialer considers the alarm as received and it enables the speakerphone in the car powering on the green signal "Received Alarm". The people in the car can now talk to the Support service. -
Page 35: Changing The Language (Command 45*Xx#)
* 1 for car 1 - * 2 for car 2 - * 3 for car 3 The command can be sent at any time. If no keys is pressed, after 2 playbacks of the welcome message 2G Lift Dialer tries to open the speakerphone with car 1. -
Page 36: Activating The Intercom Function (Command *1 Or *2 Or *3)
* 1 for car 1 - * 2 for car 2 - * 3 for car 3 The command can be sent at any time. If no keys is pressed, after 2 playbacks of the welcome message 2G Lift Dialer tries to open the speakerphone with car 1. -
Page 37: Relay1: Bell Management (Command 84T#)
12-13). The bell must be powered with external power supply. The old 2 wires of the bell that from the machine room goes down to the cabin are to be connected to pins 5-6 of 2G Lift Dialer. The other end of the old 2 wires of the bell arriving in the cabin are to be disconnected from the alarm button and connected to the pins 1-2 of VoiceBox. - Page 40 Italy 21010 Cardano al Campo VA via Alessandro Volta 39 http://www.digicom.it...