Rear Exit; Rear Exit Shield (For Rear Vent Only) - Napoleon Ascent 46 Installation And Operation Manual

3.11

rear exit

EN
venting requirements
EN
FAILURE TO CREATE A SEAL TO THE FIREBOX WITH THE EXHAUST COLLAR ASSEMBLY WILL CAUSE
2.10 rear exit THE APPLIANCE TO FUNCTION IMPROPERLY AND CAN CAUSE INJURY OR PROPERTY DAMAGE.
WARNING
!
Remove the safety screen and glass front, refer to " SAFETY
A.
• Failure to create a seal to the firebix with the exhaust collar assembly will cause the appliance to function
SCREEN / DOOR REMOVAL AND INSTALLATION" section.
improperly and can cause injury or property damage.
Remove the contents from the firebox and set aside, you will
B.
need the exhaust flue collar from the top of the log carton.
Remove the safety barrier and glass door (see "safety barrier / door removal and installation" section).
A.
To ease assembly, remove the four hex head screws securing
C.
Remove the contents from the firebox and set aside. You will
B.
the deflector from inside the top front of the firebox, refer to
need the exhaust flue collar from the top of the log carton.
Figure 1.
To ease assembly, remove the four hex head screws securing
C.
Place the gasket (provided) over the 4" (102mm) flue collar assembly and
D.
the deflector from inside the top front of the firebox (Fig. 1).
bend along perforation.
Place the gasket (supplied) over the 4" (102mm) flue collar
D.
From inside the firebox, insert the 4" (102mm) flue collar through the back
E.
assembly and bend along perforation.
of the firebox. Install the rear exit shield onto the 4" (102mm) flue collar, see
From inside the firebox, insert the 4" (102mm) flue collar through
E. "REAR EXIT SHIELD" section for installation instructions.
the back of the firebox. Install the rear exit shield onto the 4" (102mm) flue collar
Secure the flue collar assembly, gasket and rear exit shield using the four
F.
(see "rear exit shield (for rear vent only)" section).
hex head 3/8" thread cutting screws, refer to Figure 2. NOTE: Do not
Secure the flue collar assembly, gasket, and baffle bracket using the four hex head
F. overtighten. The gasket needs only to be snug against the firebox.
3/8" thread cutting screws (Fig. 2).
Reattach the deflector using the four screws and install the log set, glass door
G.
note:
and safety screen.
Do not overtighten. The gasket only needs to be snug against the firebox.
Reattach the deflector using the four screws, and re-install glass door and safety
G.
barrier.
3.12

rear exit shield (for rear vent only)

Remove the safety barrier assembly and door from the appliance, refer to the "SAFETY SCREEN &
2.11 A. rear exit shield (for rear vent only)
DOOR REMOVAL / INSTALLATION" section of the manual for detailed instructions.
Remove the safety barrier assembly and door from the appliance (see "safety barrier / door removal and
A.
installation" section).
Loosen the two screws, that secure the exhaust plate, and slide the baffle in place by sliding its
B.
slotted openings behind the screwheads, tighten the two previously loosened screws. Refer to the
Loosen the two screws that secure the exhaust plate, and slide the rear exit shield in place by
B.
illustration below.
sliding its slotted openings behind the screwheads.Tighten the two previously loosened screws (Fig. 1).
Reinstall the door and safety barrier assembly on the appliance, refer to the "SAFETY SCREEN &
C.
Reinstall the door and safety barrier assembly on the appliance (see "safety barrier / door removal and
C.
DOOR REMOVAL / INSTALLATION" section of the manual for detailed instructions.
installation" section).
NOTE: THIS SHIELD IS USED TO BLOCK THE VIEW THROUGH THE VENTING TO THE OUTDOORS.
W415-1293 / F / 11.23.17
22
W415-2370 / D / 12.09.20
note:
This shield is used to block the view through the venting to the outdoors.
WARNING
!
Fig. 1
DEFLECTOR
DÉFLECTEUR
DEFLECTOR
DÉFLECTEUR
Fig. 2
Fig. 1
Fig. 1
Fig. 2